Command line options to assign perimeters and infill to different extruders

README.markdown

@@ -240,6 +240,13 @@ The author is Alessandro Ranellucci.
         --support-material-extrusion-width
                             Set a different extrusion width for support material
         --bridge-flow-ratio Multiplier for extrusion when bridging (> 0, default: 1)
+  
+       Multiple extruder options:
+        --perimeters-extruder
+                            Extruder to use for perimeters (1+, default: 1)
+        --infill-extruder   Extruder to use for infill (1+, default: 1)
+        --support-material-extruder
+                            Extruder to use for support material (1+, default: 1)
             
 
 

lib/Slic3r.pm

@@ -81,6 +81,11 @@ our $extrusion_multiplier   = [1];
 our $temperature            = [200];
 our $first_layer_temperature= [];
 
+# extruder mapping (1-based indexes)
+our $perimeters_extruder        = 1;
+our $infill_extruder            = 1;
+our $support_material_extruder  = 1;
+
 # speed options
 our $travel_speed           = 130;      # mm/s
 our $perimeter_speed        = 30;       # mm/s
@@ -134,7 +139,6 @@ our $support_material_threshold = 45;
 our $support_material_pattern = 'rectilinear';
 our $support_material_spacing = 2.5;
 our $support_material_angle = 0;
-our $support_material_extruder = 0;
 our $start_gcode = "G28 ; home all axes";
 our $end_gcode = <<"END";
 M104 S0 ; turn off temperature

lib/Slic3r/Config.pm

@@ -121,6 +121,23 @@ our $Options = {
         deserialize => sub { [ split /,/, $_[0] ] },
     },
     
+    # extruder mapping
+    'perimeters_extruder' => {
+        label   => 'Perimeters extruder',
+        cli     => 'perimeters-extruder=i',
+        type    => 'i',
+    },
+    'infill_extruder' => {
+        label   => 'Infill extruder',
+        cli     => 'infill-extruder=i',
+        type    => 'i',
+    },
+    'support_material_extruder' => {
+        label   => 'Extruder',
+        cli     => 'support-material-extruder=i',
+        type    => 'i',
+    },
+    
     # filament options
     'first_layer_bed_temperature' => {
         label   => 'First layer bed temperature (°C)',
@@ -329,11 +346,6 @@ our $Options = {
         cli     => 'support-material-angle=i',
         type    => 'i',
     },
-    'support_material_extruder' => {
-        label   => 'Extruder',
-        cli     => 'support-material-extruder=i',
-        type    => 'i',
-    },
     'start_gcode' => {
         label   => 'Start G-code',
         cli     => 'start-gcode=s',
@@ -688,7 +700,7 @@ sub validate {
     
     # initialize extruder(s)
     $Slic3r::extruders = [];
-    for my $t (0, $Slic3r::support_material_extruder-1) {
+    for my $t (0, map $_-1, $Slic3r::perimeters_extruder, $Slic3r::infill_extruder, $Slic3r::support_material_extruder) {
         $Slic3r::extruders->[$t] ||= Slic3r::Extruder->new(
             map { $_ => Slic3r::Config->get($_)->[$t] // Slic3r::Config->get($_)->[0] } #/
                 qw(nozzle_diameter filament_diameter extrusion_multiplier temperature first_layer_temperature)
@@ -703,9 +715,11 @@ sub validate {
             width        => $Slic3r::first_layer_extrusion_width,
         );
     }
-    $Slic3r::perimeters_flow        = $Slic3r::extruders->[0]->make_flow(width => $Slic3r::perimeters_extrusion_width || $Slic3r::extrusion_width);
-    $Slic3r::infill_flow            = $Slic3r::extruders->[0]->make_flow(width => $Slic3r::infill_extrusion_width || $Slic3r::extrusion_width);
-    $Slic3r::support_material_flow  = $Slic3r::extruders->[ $Slic3r::support_material_extruder ]
+    $Slic3r::perimeters_flow = $Slic3r::extruders->[ $Slic3r::perimeters_extruder-1 ]
+        ->make_flow(width => $Slic3r::perimeters_extrusion_width || $Slic3r::extrusion_width);
+    $Slic3r::infill_flow = $Slic3r::extruders->[ $Slic3r::infill_extruder-1 ]
+        ->make_flow(width => $Slic3r::infill_extrusion_width || $Slic3r::extrusion_width);
+    $Slic3r::support_material_flow = $Slic3r::extruders->[ $Slic3r::support_material_extruder-1 ]
         ->make_flow(width => $Slic3r::support_material_extrusion_width || $Slic3r::extrusion_width);
     
     Slic3r::debugf "Default flow width = %s, spacing = %s, min_spacing = %s\n",

lib/Slic3r/Print.pm

@@ -596,9 +596,11 @@ sub write_gcode {
             $gcodegen->shift_y($shift[Y] + unscale $copy->[Y]);
             
             # extrude perimeters
+            $gcode .= $gcodegen->set_tool($Slic3r::perimeters_extruder-1);
             $gcode .= $gcodegen->extrude($_, 'perimeter') for @{ $layer->perimeters };
             
             # extrude fills
+            $gcode .= $gcodegen->set_tool($Slic3r::infill_extruder-1);
             $gcode .= $gcodegen->set_acceleration($Slic3r::infill_acceleration);
             for my $fill (@{ $layer->fills }) {
                 $gcode .= $gcodegen->extrude_path($_, 'fill') 
@@ -610,7 +612,6 @@ sub write_gcode {
                 $gcode .= $gcodegen->set_tool($Slic3r::support_material_extruder-1);
                 $gcode .= $gcodegen->extrude_path($_, 'support material') 
                     for $layer->support_fills->shortest_path($gcodegen->last_pos);
-                $gcode .= $gcodegen->set_tool(0);
             }
         }
         return if !$gcode;

slic3r.pl

@@ -285,6 +285,13 @@ $j
     --support-material-extrusion-width
                         Set a different extrusion width for support material
     --bridge-flow-ratio Multiplier for extrusion when bridging (> 0, default: $Slic3r::bridge_flow_ratio)
+  
+   Multiple extruder options:
+    --perimeters-extruder
+                        Extruder to use for perimeters (1+, default: 1)
+    --infill-extruder   Extruder to use for infill (1+, default: 1)
+    --support-material-extruder
+                        Extruder to use for support material (1+, default: 1)
     
 EOF
     exit ($exit_code || 0);