398 lines
11 KiB
C
398 lines
11 KiB
C
/*-
|
|
* Copyright (c) 2014-2015 M. Warner Losh <imp@freebsd.org>
|
|
* Copyright (c) 2015 Luiz Otavio O Souza <loos@freebsd.org>
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*
|
|
* The magic-bit-bang sequence used in this code may be based on a linux
|
|
* platform driver in the Allwinner SDK from Allwinner Technology Co., Ltd.
|
|
* www.allwinnertech.com, by Daniel Wang <danielwang@allwinnertech.com>
|
|
* though none of the original code was copied.
|
|
*/
|
|
|
|
#include "opt_bus.h"
|
|
|
|
#include <sys/cdefs.h>
|
|
__FBSDID("$FreeBSD$");
|
|
|
|
#include <sys/param.h>
|
|
#include <sys/systm.h>
|
|
#include <sys/bus.h>
|
|
#include <sys/rman.h>
|
|
#include <sys/kernel.h>
|
|
#include <sys/module.h>
|
|
|
|
#include <machine/bus.h>
|
|
#include <dev/ofw/ofw_bus.h>
|
|
#include <dev/ofw/ofw_bus_subr.h>
|
|
|
|
#include <dev/ahci/ahci.h>
|
|
#include <dev/extres/clk/clk.h>
|
|
|
|
/*
|
|
* Allwinner a1x/a2x/a8x SATA attachment. This is just the AHCI register
|
|
* set with a few extra implementation-specific registers that need to
|
|
* be accounted for. There's only one PHY in the system, and it needs
|
|
* to be trained to bring the link up. In addition, there's some DMA
|
|
* specific things that need to be done as well. These things are also
|
|
* just about completely undocumented, except in ugly code in the Linux
|
|
* SDK Allwinner releases.
|
|
*/
|
|
|
|
/* BITx -- Unknown bit that needs to be set/cleared at position x */
|
|
/* UFx -- Uknown multi-bit field frobbed during init */
|
|
#define AHCI_BISTAFR 0x00A0
|
|
#define AHCI_BISTCR 0x00A4
|
|
#define AHCI_BISTFCTR 0x00A8
|
|
#define AHCI_BISTSR 0x00AC
|
|
#define AHCI_BISTDECR 0x00B0
|
|
#define AHCI_DIAGNR 0x00B4
|
|
#define AHCI_DIAGNR1 0x00B8
|
|
#define AHCI_OOBR 0x00BC
|
|
#define AHCI_PHYCS0R 0x00C0
|
|
/* Bits 0..17 are a mystery */
|
|
#define PHYCS0R_BIT18 (1 << 18)
|
|
#define PHYCS0R_POWER_ENABLE (1 << 19)
|
|
#define PHYCS0R_UF1_MASK (7 << 20) /* Unknown Field 1 */
|
|
#define PHYCS0R_UF1_INIT (3 << 20)
|
|
#define PHYCS0R_BIT23 (1 << 23)
|
|
#define PHYCS0R_UF2_MASK (7 << 24) /* Uknown Field 2 */
|
|
#define PHYCS0R_UF2_INIT (5 << 24)
|
|
/* Bit 27 mystery */
|
|
#define PHYCS0R_POWER_STATUS_MASK (7 << 28)
|
|
#define PHYCS0R_PS_GOOD (2 << 28)
|
|
/* Bit 31 mystery */
|
|
#define AHCI_PHYCS1R 0x00C4
|
|
/* Bits 0..5 are a mystery */
|
|
#define PHYCS1R_UF1_MASK (3 << 6)
|
|
#define PHYCS1R_UF1_INIT (2 << 6)
|
|
#define PHYCS1R_UF2_MASK (0x1f << 8)
|
|
#define PHYCS1R_UF2_INIT (6 << 8)
|
|
/* Bits 13..14 are a mystery */
|
|
#define PHYCS1R_BIT15 (1 << 15)
|
|
#define PHYCS1R_UF3_MASK (3 << 16)
|
|
#define PHYCS1R_UF3_INIT (2 << 16)
|
|
/* Bit 18 mystery */
|
|
#define PHYCS1R_HIGHZ (1 << 19)
|
|
/* Bits 20..27 mystery */
|
|
#define PHYCS1R_BIT28 (1 << 28)
|
|
/* Bits 29..31 mystery */
|
|
#define AHCI_PHYCS2R 0x00C8
|
|
/* bits 0..4 mystery */
|
|
#define PHYCS2R_UF1_MASK (0x1f << 5)
|
|
#define PHYCS2R_UF1_INIT (0x19 << 5)
|
|
/* Bits 10..23 mystery */
|
|
#define PHYCS2R_CALIBRATE (1 << 24)
|
|
/* Bits 25..31 mystery */
|
|
#define AHCI_TIMER1MS 0x00E0
|
|
#define AHCI_GPARAM1R 0x00E8
|
|
#define AHCI_GPARAM2R 0x00EC
|
|
#define AHCI_PPARAMR 0x00F0
|
|
#define AHCI_TESTR 0x00F4
|
|
#define AHCI_VERSIONR 0x00F8
|
|
#define AHCI_IDR 0x00FC
|
|
#define AHCI_RWCR 0x00FC
|
|
|
|
#define AHCI_P0DMACR 0x0070
|
|
#define AHCI_P0PHYCR 0x0078
|
|
#define AHCI_P0PHYSR 0x007C
|
|
|
|
#define PLL_FREQ 100000000
|
|
|
|
static void inline
|
|
ahci_set(struct resource *m, bus_size_t off, uint32_t set)
|
|
{
|
|
uint32_t val = ATA_INL(m, off);
|
|
|
|
val |= set;
|
|
ATA_OUTL(m, off, val);
|
|
}
|
|
|
|
static void inline
|
|
ahci_clr(struct resource *m, bus_size_t off, uint32_t clr)
|
|
{
|
|
uint32_t val = ATA_INL(m, off);
|
|
|
|
val &= ~clr;
|
|
ATA_OUTL(m, off, val);
|
|
}
|
|
|
|
static void inline
|
|
ahci_mask_set(struct resource *m, bus_size_t off, uint32_t mask, uint32_t set)
|
|
{
|
|
uint32_t val = ATA_INL(m, off);
|
|
|
|
val &= mask;
|
|
val |= set;
|
|
ATA_OUTL(m, off, val);
|
|
}
|
|
|
|
/*
|
|
* Should this be phy_reset or phy_init
|
|
*/
|
|
#define PHY_RESET_TIMEOUT 1000
|
|
static void
|
|
ahci_a10_phy_reset(device_t dev)
|
|
{
|
|
uint32_t to, val;
|
|
struct ahci_controller *ctlr = device_get_softc(dev);
|
|
|
|
/*
|
|
* Here starts the magic -- most of the comments are based
|
|
* on guesswork, names of routines and printf error
|
|
* messages. The code works, but it will do that even if the
|
|
* comments are 100% BS.
|
|
*/
|
|
|
|
/*
|
|
* Lock out other access while we initialize. Or at least that
|
|
* seems to be the case based on Linux SDK #defines. Maybe this
|
|
* put things into reset?
|
|
*/
|
|
ATA_OUTL(ctlr->r_mem, AHCI_RWCR, 0);
|
|
DELAY(100);
|
|
|
|
/*
|
|
* Set bit 19 in PHYCS1R. Guessing this disables driving the PHY
|
|
* port for a bit while we reset things.
|
|
*/
|
|
ahci_set(ctlr->r_mem, AHCI_PHYCS1R, PHYCS1R_HIGHZ);
|
|
|
|
/*
|
|
* Frob PHYCS0R...
|
|
*/
|
|
ahci_mask_set(ctlr->r_mem, AHCI_PHYCS0R,
|
|
~PHYCS0R_UF2_MASK,
|
|
PHYCS0R_UF2_INIT | PHYCS0R_BIT23 | PHYCS0R_BIT18);
|
|
|
|
/*
|
|
* Set three fields in PHYCS1R
|
|
*/
|
|
ahci_mask_set(ctlr->r_mem, AHCI_PHYCS1R,
|
|
~(PHYCS1R_UF1_MASK | PHYCS1R_UF2_MASK | PHYCS1R_UF3_MASK),
|
|
PHYCS1R_UF1_INIT | PHYCS1R_UF2_INIT | PHYCS1R_UF3_INIT);
|
|
|
|
/*
|
|
* Two more mystery bits in PHYCS1R. -- can these be combined above?
|
|
*/
|
|
ahci_set(ctlr->r_mem, AHCI_PHYCS1R, PHYCS1R_BIT15 | PHYCS1R_BIT28);
|
|
|
|
/*
|
|
* Now clear that first mysery bit. Perhaps this starts
|
|
* driving the PHY again so we can power it up and start
|
|
* talking to the SATA drive, if any below.
|
|
*/
|
|
ahci_clr(ctlr->r_mem, AHCI_PHYCS1R, PHYCS1R_HIGHZ);
|
|
|
|
/*
|
|
* Frob PHYCS0R again...
|
|
*/
|
|
ahci_mask_set(ctlr->r_mem, AHCI_PHYCS0R,
|
|
~PHYCS0R_UF1_MASK, PHYCS0R_UF1_INIT);
|
|
|
|
/*
|
|
* Frob PHYCS2R, because 25 means something?
|
|
*/
|
|
ahci_mask_set(ctlr->r_mem, AHCI_PHYCS2R, ~PHYCS2R_UF1_MASK,
|
|
PHYCS2R_UF1_INIT);
|
|
|
|
DELAY(100); /* WAG */
|
|
|
|
/*
|
|
* Turn on the power to the PHY and wait for it to report back
|
|
* good?
|
|
*/
|
|
ahci_set(ctlr->r_mem, AHCI_PHYCS0R, PHYCS0R_POWER_ENABLE);
|
|
for (to = PHY_RESET_TIMEOUT; to > 0; to--) {
|
|
val = ATA_INL(ctlr->r_mem, AHCI_PHYCS0R);
|
|
if ((val & PHYCS0R_POWER_STATUS_MASK) == PHYCS0R_PS_GOOD)
|
|
break;
|
|
DELAY(10);
|
|
}
|
|
if (to == 0 && bootverbose)
|
|
device_printf(dev, "PHY Power Failed PHYCS0R = %#x\n", val);
|
|
|
|
/*
|
|
* Calibrate the clocks between the device and the host. This appears
|
|
* to be an automated process that clears the bit when it is done.
|
|
*/
|
|
ahci_set(ctlr->r_mem, AHCI_PHYCS2R, PHYCS2R_CALIBRATE);
|
|
for (to = PHY_RESET_TIMEOUT; to > 0; to--) {
|
|
val = ATA_INL(ctlr->r_mem, AHCI_PHYCS2R);
|
|
if ((val & PHYCS2R_CALIBRATE) == 0)
|
|
break;
|
|
DELAY(10);
|
|
}
|
|
if (to == 0 && bootverbose)
|
|
device_printf(dev, "PHY Cal Failed PHYCS2R %#x\n", val);
|
|
|
|
/*
|
|
* OK, let things settle down a bit.
|
|
*/
|
|
DELAY(1000);
|
|
|
|
/*
|
|
* Go back into normal mode now that we've calibrated the PHY.
|
|
*/
|
|
ATA_OUTL(ctlr->r_mem, AHCI_RWCR, 7);
|
|
}
|
|
|
|
static void
|
|
ahci_a10_ch_start(struct ahci_channel *ch)
|
|
{
|
|
uint32_t reg;
|
|
|
|
/*
|
|
* Magical values from Allwinner SDK, setup the DMA before start
|
|
* operations on this channel.
|
|
*/
|
|
reg = ATA_INL(ch->r_mem, AHCI_P0DMACR);
|
|
reg &= ~0xff00;
|
|
reg |= 0x4400;
|
|
ATA_OUTL(ch->r_mem, AHCI_P0DMACR, reg);
|
|
}
|
|
|
|
static int
|
|
ahci_a10_ctlr_reset(device_t dev)
|
|
{
|
|
|
|
ahci_a10_phy_reset(dev);
|
|
|
|
return (ahci_ctlr_reset(dev));
|
|
}
|
|
|
|
static int
|
|
ahci_a10_probe(device_t dev)
|
|
{
|
|
|
|
if (!ofw_bus_is_compatible(dev, "allwinner,sun4i-a10-ahci"))
|
|
return (ENXIO);
|
|
device_set_desc(dev, "Allwinner Integrated AHCI controller");
|
|
|
|
return (BUS_PROBE_DEFAULT);
|
|
}
|
|
|
|
static int
|
|
ahci_a10_attach(device_t dev)
|
|
{
|
|
int error;
|
|
struct ahci_controller *ctlr;
|
|
clk_t clk_pll, clk_gate;
|
|
|
|
ctlr = device_get_softc(dev);
|
|
clk_pll = clk_gate = NULL;
|
|
|
|
ctlr->quirks = AHCI_Q_NOPMP;
|
|
ctlr->vendorid = 0;
|
|
ctlr->deviceid = 0;
|
|
ctlr->subvendorid = 0;
|
|
ctlr->subdeviceid = 0;
|
|
ctlr->r_rid = 0;
|
|
if (!(ctlr->r_mem = bus_alloc_resource_any(dev, SYS_RES_MEMORY,
|
|
&ctlr->r_rid, RF_ACTIVE)))
|
|
return (ENXIO);
|
|
|
|
/* Enable clocks */
|
|
error = clk_get_by_ofw_index(dev, 0, &clk_pll);
|
|
if (error != 0) {
|
|
device_printf(dev, "Cannot get PLL clock\n");
|
|
goto fail;
|
|
}
|
|
error = clk_get_by_ofw_index(dev, 1, &clk_gate);
|
|
if (error != 0) {
|
|
device_printf(dev, "Cannot get gate clock\n");
|
|
goto fail;
|
|
}
|
|
error = clk_set_freq(clk_pll, PLL_FREQ, CLK_SET_ROUND_DOWN);
|
|
if (error != 0) {
|
|
device_printf(dev, "Cannot set PLL frequency\n");
|
|
goto fail;
|
|
}
|
|
error = clk_enable(clk_pll);
|
|
if (error != 0) {
|
|
device_printf(dev, "Cannot enable PLL\n");
|
|
goto fail;
|
|
}
|
|
error = clk_enable(clk_gate);
|
|
if (error != 0) {
|
|
device_printf(dev, "Cannot enable clk gate\n");
|
|
goto fail;
|
|
}
|
|
|
|
/* Reset controller */
|
|
if ((error = ahci_a10_ctlr_reset(dev)) != 0)
|
|
goto fail;
|
|
|
|
/*
|
|
* No MSI registers on this platform.
|
|
*/
|
|
ctlr->msi = 0;
|
|
ctlr->numirqs = 1;
|
|
|
|
/* Channel start callback(). */
|
|
ctlr->ch_start = ahci_a10_ch_start;
|
|
|
|
/*
|
|
* Note: ahci_attach will release ctlr->r_mem on errors automatically
|
|
*/
|
|
return (ahci_attach(dev));
|
|
|
|
fail:
|
|
if (clk_gate != NULL)
|
|
clk_release(clk_gate);
|
|
if (clk_pll != NULL)
|
|
clk_release(clk_pll);
|
|
bus_release_resource(dev, SYS_RES_MEMORY, ctlr->r_rid, ctlr->r_mem);
|
|
return (error);
|
|
}
|
|
|
|
static int
|
|
ahci_a10_detach(device_t dev)
|
|
{
|
|
|
|
return (ahci_detach(dev));
|
|
}
|
|
|
|
devclass_t ahci_devclass;
|
|
|
|
static device_method_t ahci_ata_methods[] = {
|
|
DEVMETHOD(device_probe, ahci_a10_probe),
|
|
DEVMETHOD(device_attach, ahci_a10_attach),
|
|
DEVMETHOD(device_detach, ahci_a10_detach),
|
|
DEVMETHOD(bus_print_child, ahci_print_child),
|
|
DEVMETHOD(bus_alloc_resource, ahci_alloc_resource),
|
|
DEVMETHOD(bus_release_resource, ahci_release_resource),
|
|
DEVMETHOD(bus_setup_intr, ahci_setup_intr),
|
|
DEVMETHOD(bus_teardown_intr,ahci_teardown_intr),
|
|
DEVMETHOD(bus_child_location_str, ahci_child_location_str),
|
|
DEVMETHOD_END
|
|
};
|
|
|
|
static driver_t ahci_ata_driver = {
|
|
"ahci",
|
|
ahci_ata_methods,
|
|
sizeof(struct ahci_controller)
|
|
};
|
|
|
|
DRIVER_MODULE(ahci, simplebus, ahci_ata_driver, ahci_devclass, 0, 0);
|