Almost all PA-RISC machines have either a button that is labeled with 'TOC' or
a BMC/GSP function to trigger a TOC. TOC is a non-maskable interrupt that is
sent to the processor. This can be used for diagnostic purposes like obtaining
a stack trace/register dump or to enter KDB/KGDB in Linux.
This patch adds support for such an emulated TOC button.
It wires up the qemu monitor "nmi" command to trigger a TOC. For that it
provides the hppa_nmi function which is assigned to the nmi_monitor_handler
function pointer. When called it raises the EXCP_TOC hardware interrupt in the
hppa_cpu_do_interrupt() function. The interrupt function then calls the
architecturally defined TOC function in SeaBIOS-hppa firmware (at fixed address
0xf0000000).
According to the PA-RISC PDC specification, the SeaBIOS firmware then writes
the CPU registers into PIM (processor internal memmory) for later analysis. In
order to write all registers it needs to know the contents of the CPU "shadow
registers" and the IASQ- and IAOQ-back values. The IAOQ/IASQ values are
provided by qemu in shadow registers when entering the SeaBIOS TOC function.
This patch adds a new aritificial opcode "getshadowregs" (0xfffdead2) which
restores the original values of the shadow registers. With this opcode SeaBIOS
can store those registers as well into PIM before calling an OS-provided TOC
handler.
To trigger a TOC, switch to the qemu monitor with Ctrl-A C, and type in the
command "nmi". After the TOC started the OS-debugger, exit the qemu monitor
with Ctrl-A C.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Stop including hw/boards.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-3-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Cc: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201026143028.3034018-5-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Emulate a power button switch, tell SeaBIOS the address via fw_cfg and
bind the power button to the qemu UI.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Change QEMU_FW_CFG_IO_BASE to shorter variant FW_CFG_IO_BASE and hand
over the actual port address in %r19 to SeaBIOS.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Until now the TLB size was fixed at 256 entries. To allow operating
systems to utilize more TLB entries in the future, we need to tell
firmware how many TLB entries we actually support in the emulation.
Firmware then reports this to the operating system via the
PDC_CACHE_INFO call.
This patch simply does the preparation to allow more TLB entries.
Signed-off-by: Helge Deller <deller@gmx.de>
It's important that the SeaBIOS hppa firmware is at least at a minimal
level to ensure proper interaction between qemu and firmware.
Implement a proper firmware version check by telling SeaBIOS via the
fw_cfg interface which minimal SeaBIOS version is required by this
running qemu instance. If the firmware detects that it's too old, it
will stop.
Signed-off-by: Helge Deller <deller@gmx.de>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
After previous clean ups we can drop direct inclusion of hw/ide.h from
several places.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: a3f72b663e537701c63cec5fc9cb8ed4f4249f28.1584457537.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
hw/hppa/machine.c uses NICInfo variables which are declared in
"net/net.h". Include it.
This fixes (when modifying unrelated headers):
hw/hppa/machine.c:126:21: error: use of undeclared identifier 'nb_nics'
for (i = 0; i < nb_nics; i++) {
^
hw/hppa/machine.c:127:30: error: use of undeclared identifier 'nd_table'
pci_nic_init_nofail(&nd_table[i], pci_bus, "e1000", NULL);
^
Acked-by: John Snow <jsnow@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200228114649.12818-10-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
There's no good reason for it to be type int, change it to bool.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200207161948.15972-3-philmd@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
memory_region_allocate_system_memory() API is going away, so
replace it with memdev allocated MemoryRegion. The later is
initialized by generic code, so board only needs to opt in
to memdev scheme by providing
MachineClass::default_ram_id
and using MachineState::ram instead of manually initializing
RAM memory region.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200219160953.13771-42-imammedo@redhat.com>
While loading the executable, some platforms (like AVR) need to
detect CPU type that executable is built for - and, with this patch,
this is enabled by reading the field 'e_flags' of the ELF header of
the executable in question. The change expands functionality of
the following functions:
- load_elf()
- load_elf_as()
- load_elf_ram()
- load_elf_ram_sym()
The argument added to these functions is called 'pflags' and is of
type 'uint32_t*' (that matches 'pointer to 'elf_word'', 'elf_word'
being the type of the field 'e_flags', in both 32-bit and 64-bit
variants of ELF header). Callers are allowed to pass NULL as that
argument, and in such case no lookup to the field 'e_flags' will
happen, and no information will be returned, of course.
CC: Richard Henderson <rth@twiddle.net>
CC: Peter Maydell <peter.maydell@linaro.org>
CC: Edgar E. Iglesias <edgar.iglesias@gmail.com>
CC: Michael Walle <michael@walle.cc>
CC: Thomas Huth <huth@tuxfamily.org>
CC: Laurent Vivier <laurent@vivier.eu>
CC: Philippe Mathieu-Daudé <f4bug@amsat.org>
CC: Aleksandar Rikalo <aleksandar.rikalo@rt-rk.com>
CC: Aurelien Jarno <aurelien@aurel32.net>
CC: Jia Liu <proljc@gmail.com>
CC: David Gibson <david@gibson.dropbear.id.au>
CC: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: BALATON Zoltan <balaton@eik.bme.hu>
CC: Christian Borntraeger <borntraeger@de.ibm.com>
CC: Thomas Huth <thuth@redhat.com>
CC: Artyom Tarasenko <atar4qemu@gmail.com>
CC: Fabien Chouteau <chouteau@adacore.com>
CC: KONRAD Frederic <frederic.konrad@adacore.com>
CC: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Aleksandar Rikalo <aleksandar.rikalo@rt-rk.com>
Signed-off-by: Michael Rolnik <mrolnik@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1580079311-20447-24-git-send-email-aleksandar.markovic@rt-rk.com>
The region in range [0xf0000000 - 0xf1000000] is the PDC area
(Processor Dependent Code), where the firmware is loaded.
This region has higher priority than the main memory.
When the machine has more than 3840MB of RAM, there is an
overlap. Since the PDC is closer to the CPU in the bus
hierarchy, it gets accessed first, and the CPU does not have
access to the RAM in this range.
To model the same behavior and keep a simple memory layout,
reduce the priority of the RAM region. The PDC region ends
overlapping the RAM.
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200109000525.24744-4-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The hardware expects DIMM slots of 1 or 2 GB, allowing up to
4 GB of memory. We want to accept the same amount of memory the
hardware can deal with. DIMMs of 768MB are not available.
However we have to deal with a firmware limitation: currently
SeaBIOS only supports 32-bit, and expects the RAM size in a
32-bit register. When using a 4GB configuration, the 32-bit
register get truncated and we report a size of 0MB to SeaBIOS,
which ends halting the machine:
$ qemu-system-hppa -m 4g -serial stdio
SeaBIOS: Machine configured with too little memory (0 MB), minimum is 16 MB.
SeaBIOS wants SYSTEM HALT.
The easiest way is to restrict the machine to 3GB of memory.
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200109000525.24744-3-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The firmware has to reside in the PDC range. If the Elf file
expects to load it below FIRMWARE_START, it is incorrect,
regardless the RAM size.
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200109000525.24744-2-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This adds emulation of Artist graphics good enough to get a text
console on both Linux and HP-UX. The X11 server from HP-UX also works.
Adjust boot-serial-test to disable graphics, so that SeaBIOS outputs
to the serial port, as expected by the test.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191220211512.3289-6-svens@stackframe.org>
[rth: Merge Helge's test for machine->enable_graphics]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Most HP PA-RISC machines have a Digital DS21142/43 Tulip network card,
only some very latest generation machines have an e1000 NIC.
Since qemu now provides an emulated tulip card, use that one instead.
Signed-off-by: Helge Deller <deller@gmx.de>
Message-Id: <20191221222530.GB27803@ls3530.fritz.box>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
LASI is a built-in multi-I/O chip which supports serial, parallel,
network (Intel i82596 Apricot), sound and other functionalities.
LASI has been used in many HP PARISC machines.
This patch adds the necessary parts to allow Linux and HP-UX to detect
LASI and the network card.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191220211512.3289-3-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Remove the need to include i386/pc.h to get to the i8259 functions.
This is enough to remove the inclusion of hw/i386/pc.h from all non-x86
files.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MC146818 is a Real Time Clock, not a timer.
Move it under the hw/rtc/ subdirectory.
Use copyright statement from 80cabfad16 for "hw/rtc/mc146818rtc.h".
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191003230404.19384-4-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
machine_hppa_init() violates memory_region_allocate_system_memory() contract
by calling it multiple times which could break with -mem-path. Replace
the second usage (for 'rom') with memory_region_init_ram() instead.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20191008113318.7012-4-imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
memory_region_init_* takes care of copying the name into memory it owns.
Free it in the caller.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing sysemu/reset.h triggers a
recompile of some 2600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
The main culprit is hw/hw.h, which supposedly includes it for
convenience.
Include sysemu/reset.h only where it's needed. Touching it now
recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-9-armbru@redhat.com>
The global smp variables in alpha/hppa/mips/openrisc/sparc*/xtensa codes
are replaced with smp properties from MachineState.
A local variable of the same name would be introduced in the declaration
phase if it's used widely in the context OR replace it on the spot if it's
only used once. No semantic changes.
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190518205428.90532-10-like.xu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
To get rid of the global smp_* variables we're currently using, it's recommended
to pass MachineState in the list of incoming parameters for functions that use
global smp variables, thus some redundant parameters are dropped. It's applied
for legacy smbios_*(), *_machine_reset(), hot_add_cpu() and mips *_create_cpu().
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190518205428.90532-3-like.xu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This patch adds an optional function pointer, 'elf_note_fn', to
load_elf() which causes load_elf() to additionally parse any
ELF program headers of type PT_NOTE and check to see if the ELF
Note is of the type specified by the 'translate_opaque' arg.
If a matching ELF Note is found then the specfied function pointer
is called to process the ELF note.
Passing a NULL function pointer results in ELF Notes being skipped.
The first consumer of this functionality is the PVHboot support
which needs to read the XEN_ELFNOTE_PHYS32_ENTRY ELF Note while
loading the uncompressed kernel binary in order to discover the
boot entry address for the x86/HVM direct boot ABI.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Previously, if the size of initrd >=2G, qemu exits with error:
root@haswell-OptiPlex-9020:/home/lizj# /home/lizhijian/lkp/qemu-colo/x86_64-softmmu/qemu-system-x86_64 -kernel ./vmlinuz-4.16.0-rc4 -initrd large.cgz -nographic
qemu: error reading initrd large.cgz: No such file or directory
root@haswell-OptiPlex-9020:/home/lizj# du -sh large.cgz
2.5G large.cgz
this patch changes the caller side that use this function to calculate
size of initrd file as well.
v2: update error message and int64_t printing format
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Message-Id: <1536833233-14121-1-git-send-email-lizhijian@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As part of commits a64aa5785d "hw: Deprecate -drive if=scsi with non-onboard
HBAs" and b891538e81 "hw/ppc/prep: Fix implicit creation of "-drive if=scsi"
devices" the lsi53c895a_create() and lsi53c810_create() functions were added
to wrap pci_create_simple() and scsi_bus_legacy_handle_cmdline().
Unfortunately this prevents us from changing qdev properties on the device
and/or changing the PCI configuration. By switching over to using the new
lsi53c8xx_handle_legacy_cmdline() function then the caller can now configure
and realize the LSI SCSI device exactly as required.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org> [arm parts]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When pulling in headers that are in the same directory as the C file (as
opposed to one in include/), we should use its relative path, without a
directory.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Change all the uses of serial_hds[] to go via the new
serial_hd() function. Code change produced with:
find hw -name '*.[ch]' | xargs sed -i -e 's/serial_hds\[\([^]]*\)\]/serial_hd(\1)/g'
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180420145249.32435-8-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Now that we have the prerequisites in target/hppa/,
implement the hardware for a PA7100LC.
This also enables build for hppa-softmmu.
Signed-off-by: Helge Deller <deller@gmx.de>
[rth: Since it is all new code, squashed all branch development
withing hw/hppa/ to a single patch.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
With the addition of default-configs/hppa-softmmu.mak, this
will compile. It is not enabled with this patch, however.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Marc-André Lureau