Per the Physical Layer Simplified Spec. "4.3.10.4 Switch Function Status":
The block length is predefined to 512 bits
and "4.10.2 SD Status":
The SD Status contains status bits that are related to the SD Memory Card
proprietary features and may be used for future application-specific usage.
The size of the SD Status is one data block of 512 bit. The content of this
register is transmitted to the Host over the DAT bus along with a 16-bit CRC.
Thus the 16-bit CRC goes at offset 64.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180509060104.4458-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This fixes an issue by adding bounds checking to multi-byte packets
where the PS/2 mouse data stream may become corrupted due to data being
discarded when the PS/2 ringbuffer is full.
Interrupts for Multi-byte responses are postponed until the final byte
has been queued.
These changes fix a bug where windows guests drop the mouse device
entirely requring the guest to be restarted.
Signed-off-by: Geoffrey McRae <geoff@hostfission.com>
Message-Id: <20180507150310.2FEA0381924@moya.office.hostfission.com>
[ kraxel: codestyle fixes ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This allows guest's to correctly reinitialize and identify the mouse
should the guest decide to re-scan or reset during mouse input events.
When the guest sends the "Identify" command, due to the PC's hardware
architecutre it is impossible to reliably determine the response from
the command amongst other streaming data, such as mouse or keyboard
events. Standard practice is for the guest to disable the device and
then issue the identify command, so this must be obeyed.
Signed-off-by: Geoffrey McRae <geoff@hostfission.com>
Message-Id: <20180507150303.7486B381924@moya.office.hostfission.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Calling pause_all_vcpus()/resume_all_vcpus() from a VCPU thread might
not be the best idea. As pause_all_vcpus() temporarily drops the qemu
mutex, two parallel calls to pause_all_vcpus() can be active at a time,
resulting in a deadlock. (either by two VCPUs or by the main thread and a
VCPU)
Let's handle it via the main loop instead, as suggested by Paolo. If we
would have two parallel reset requests by two different VCPUs at the
same time, the last one would win.
We use the existing ipl device to handle it. The nice side effect is
that we can get rid of reipl_requested.
This change implies that all reset handling now goes via the common
path, so "no-reboot" handling is now active for all kinds of reboots.
Let's execute any CPU initialization code on the target CPU using
run_on_cpu.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180424101859.10239-1-david@redhat.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Thomas reported that the subchannel for a 3270 device that ended up
in a broken state (status pending even though not enabled) did not
get out of that state even after a reboot (which involves a subsytem
reset). The reason for this is that the 3270 device did not define
a reset handler.
Let's fix this by introducing a base reset handler (set up for all
ccw devices) that resets the subchannel and have virtio-ccw call
its virtio-specific reset procedure in addition to that.
CC: qemu-stable@nongnu.org
Reported-by: Thomas Huth <thuth@redhat.com>
Suggested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
All the different virtio ccw devices use the same reset handler,
so let's move setting it into the base virtio ccw device class.
CC: qemu-stable@nongnu.org
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The 3270 code will try to post an attention interrupt when the
3270 emulator (e.g. x3270) attaches. If the guest has not yet
enabled the subchannel for the 3270 device, we will present a spurious
cc 1 (status pending) when it uses msch on it later on, e.g. when
trying to enable the subchannel.
To fix this, just don't do anything in css_conditional_io_interrupt()
if the subchannel is not enabled. The 3270 code will work fine with
that, and the other user of this function (virtio-ccw) never
attempts to post an interrupt for a disabled device to begin with.
CC: qemu-stable@nongnu.org
Reported-by: Thomas Huth <thuth@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJa+UAZAAoJEO8Ells5jWIRTJIIAIcpNROupxHEfcAQKU7lIqys
qx/FxKp+lknzzQMwUfmZwT3PuBD+tWuE7ugXgzjVulvE11F+Z3QBPTDBtOObaMa1
qpgIF3zzrNxtuWMc/72Q8/wEE1wtBUo+WTAGw9Xp1dVomYOOsg1wa7dsKdZhRfz7
nIwDW2ftw3/mx+uTW2/a163v+IDDL9L+HOLibQHWUxOMM39ASchiqAXLF4mfhpwH
xr0OPd7wtcmrDsD/CLbdkGCJ/+vsXnY8pzNmy1RjJuDpWpqlgYpJJPtLBfXBo9VA
91sz5+KryzjpXXzKcQuhiU020O1dIKIe3PWqK6z0x0UjtZ1Yox5adZ3eFomHHwU=
=bIws
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Mon 14 May 2018 08:51:53 BST
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
net: Get rid of 'vlan' terminology and use 'hub' instead in the doc files
net: Get rid of 'vlan' terminology and use 'hub' instead in the source files
net: Remove the deprecated "vlan" parameter
net: Fix memory leak in net_param_nic()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* dtc configure fixes
* MemoryRegionCache second try
* Deprecated option removal
* add support for Hyper-V reenlightenment MSRs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJa9Y2qAAoJEL/70l94x66Df8EIAI4pi+zf1mTlH0Koi+oqOg+d
geBC6N9IA+n1p90XERnPbuiT19NjON2R1Z907SbzDkijxdNRoYUoQf7Z+ZBTENjn
dYsVvgLYzajGLWWtJetPPaNFAqeF2z8B3lbVQnGVLzH5pQQ2NS1NJsvXQA2LslLs
2ll1CJ2EEBhayoBSbHK+0cY85f+DUgK/T1imIV2T/rwcef9Rw218nvPfGhPBSoL6
tI2xIOxz8bBOvZNg2wdxpaoPuDipBFu6koVVbaGSgXORg8k5CEcKNxInztufdELW
KZK5ORa3T0uqu5T/GGPAfm/NbYVQ4aTB5mddshsXtKbBhnbSfRYvpVsR4kQB/Hc=
=oC1r
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Don't silently truncate extremely long words in the command line
* dtc configure fixes
* MemoryRegionCache second try
* Deprecated option removal
* add support for Hyper-V reenlightenment MSRs
# gpg: Signature made Fri 11 May 2018 13:33:46 BST
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (29 commits)
rename included C files to foo.inc.c, remove osdep.h
pc-dimm: fix error messages if no slots were defined
build: Silence dtc directory creation
shippable: Remove Debian 8 libfdt kludge
configure: Display if libfdt is from system or git
configure: Really use local libfdt if the system one is too old
i386/kvm: add support for Hyper-V reenlightenment MSRs
qemu-doc: provide details of supported build platforms
qemu-options: Remove deprecated -no-kvm-irqchip
qemu-options: Remove deprecated -no-kvm-pit-reinjection
qemu-options: Bail out on unsupported options instead of silently ignoring them
qemu-options: Remove remainders of the -tdf option
qemu-options: Mark -virtioconsole as deprecated
target/i386: sev: fix memory leaks
opts: don't silently truncate long option values
opts: don't silently truncate long parameter keys
accel: use g_strsplit for parsing accelerator names
update-linux-headers: drop hyperv.h
qemu-thread: always keep the posix wrapper layer
exec: reintroduce MemoryRegion caching
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It's been marked as deprecated since QEMU v2.9.0, so that should have
been enough time for everybody to either just drop unnecessary "vlan=0"
parameters, to switch to the modern -device + -netdev syntax for connecting
guest NICs with host network backends, or to switch to the "hubport" netdev
in case hubs are really wanted instead.
Buglink: https://bugs.launchpad.net/qemu/+bug/658904
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
* hw/arm/iotkit.c: fix minor memory leak
* softfloat: fix wrong-exception-flags bug for multiply-add corner case
* arm: isolate and clean up DTB generation
* implement Arm v8.1-Atomics extension
* Fix some bugs and missing instructions in the v8.2-FP16 extension
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uXY+
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20180510' into staging
target-arm queue:
* hw/arm/iotkit.c: fix minor memory leak
* softfloat: fix wrong-exception-flags bug for multiply-add corner case
* arm: isolate and clean up DTB generation
* implement Arm v8.1-Atomics extension
* Fix some bugs and missing instructions in the v8.2-FP16 extension
# gpg: Signature made Thu 10 May 2018 18:44:34 BST
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20180510: (21 commits)
target/arm: Clear SVE high bits for FMOV
target/arm: Fix float16 to/from int16
target/arm: Implement vector shifted FCVT for fp16
target/arm: Implement vector shifted SCVF/UCVF for fp16
target/arm: Enable ARM_FEATURE_V8_ATOMICS for user-only
target/arm: Implement CAS and CASP
target/arm: Fill in disas_ldst_atomic
target/arm: Introduce ARM_FEATURE_V8_ATOMICS and initial decode
target/riscv: Use new atomic min/max expanders
tcg: Use GEN_ATOMIC_HELPER_FN for opposite endian atomic add
tcg: Introduce atomic helpers for integer min/max
target/xtensa: Use new min/max expanders
target/arm: Use new min/max expanders
tcg: Introduce helpers for integer min/max
atomic.h: Work around gcc spurious "unused value" warning
make sure that we aren't overwriting mc->get_hotplug_handler by accident
arm/boot: split load_dtb() from arm_load_kernel()
platform-bus-device: use device plug callback instead of machine_done notifier
pc: simplify MachineClass::get_hotplug_handler handling
softfloat: Handle default NaN mode after pickNaNMulAdd, not before
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# target/riscv/translate.c
If no slots were defined we try to allocate an empty bitmap, which
fails.
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20180427120515.24067-1-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
load_dtb() depends on arm_load_kernel() to figure out place
in RAM where it should be loaded, but it's not required for
arm_load_kernel() to work. Sometimes it's neccesary for
devices added with -device/device_add to be enumerated in
DTB as well, which's lead to [1] and surrounding commits to
add 2 more machine_done notifiers with non obvious ordering
to make dynamic sysbus devices initialization happen in
the right order.
However instead of moving whole arm_load_kernel() in to
machine_done, it's sufficient to move only load_dtb() into
virt_machine_done() notifier and remove ArmLoadKernelNotifier/
/PlatformBusFDTNotifierParams notifiers, which saves us ~90LOC
and simplifies code flow quite a bit.
Later would allow to consolidate DTB generation within one
function for 'mach-virt' board and make it reentrant so it
could generate updated DTB in device hotplug secenarios.
While at it rename load_dtb() to arm_load_dtb() since it's
public now.
Add additional field skip_dtb_autoload to struct arm_boot_info
to allow manual DTB load later in mach-virt and to avoid touching
all other boards to explicitly call arm_load_dtb().
1) (ac9d32e hw/arm/boot: arm_load_kernel implemented as a machine init done notifier)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1525691524-32265-4-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
platform-bus were using machine_done notifier to get and map
(assign irq/mmio resources) dynamically added sysbus devices
after all '-device' options had been processed.
That however creates non obvious dependencies on ordering of
machine_done notifiers and requires carefull line juggling
to keep it working. For example see comment above
create_platform_bus() and 'straitforward' arm_load_kernel()
had to converted to machine_done notifier and that lead to
yet another machine_done notifier to keep it working
arm_register_platform_bus_fdt_creator().
Instead of hiding resource assignment in platform-bus-device
to magically initialize sysbus devices, use device plug
callback and assign resources explicitly at board level
at the moment each -device option is being processed.
That adds a bunch of machine declaration boiler plate to
e500plat board, similar to ARM/x86 but gets rid of hidden
machine_done notifier and would allow to remove the dependent
notifiers in ARM code simplifying it and making code flow
easier to follow.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-id: 1525691524-32265-3-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
By default MachineClass::get_hotplug_handler is NULL and concrete board
should set it to it's own handler.
Considering there isn't any default handler, drop saving empty
MachineClass::get_hotplug_handler in child class and make PC code
consistent with spapr/s390x boards.
We can bring this back when actual usecase surfaces and do it
consistently across boards that use get_hotplug_handler().
Suggested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 1525691524-32265-2-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Coverity (CID1390573) spots that we forgot to free the
gpioname strings in a loop in the iotkit realize function.
Correct the error.
This isn't a significant leak, because this function
only ever runs once.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-id: 20180427110137.19304-1-peter.maydell@linaro.org
* Require libfdt when configuring for 'riscv*-softmmu'
* Increase HTIF priority and allow zero base address
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQR8mZMOsXzYugc9Xvpr8dezV+8+TwUCWvLKRQAKCRBr8dezV+8+
TyOrAKCBiArCoNOD0lIvSdgu8Dv7dKOUaQCeMfS/FkM9wSTOnZgOPKPEZ3xreLY=
=wUet
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/riscv/tags/riscv-qemu-2.13-minor-fixes-3' into staging
RISC-V: QEMU 2.13 Minor Fixes
* Require libfdt when configuring for 'riscv*-softmmu'
* Increase HTIF priority and allow zero base address
# gpg: Signature made Wed 09 May 2018 11:15:33 BST
# gpg: using DSA key 6BF1D7B357EF3E4F
# gpg: Good signature from "Michael Clark <michaeljclark@mac.com>"
# gpg: aka "Michael Clark <mjc@sifive.com>"
# gpg: aka "Michael Clark <michael@metaparadigm.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 7C99 930E B17C D8BA 073D 5EFA 6BF1 D7B3 57EF 3E4F
* remotes/riscv/tags/riscv-qemu-2.13-minor-fixes-3:
riscv: requires libfdt
riscv: htif: increase the priority of the htif subregion
riscv: spike: allow base == 0
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The sanity check on base doesn't allow htif to be mapped @0. Check if the
symbol exists instead so we can map it where we want.
Reviewed-by: Michael Clark <mjc@sifive.com>
Signed-off-by: KONRAD Frederic <frederic.konrad@adacore.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Message-Id: <1525360636-18229-2-git-send-email-frederic.konrad@adacore.com>
* pc-dimm: factor out MemoryDevice
(virtio-pmem and virtio-mem will make use of the new abstraction later)
* scripts/device-crash-test: Removed fixed CAN entries
-----BEGIN PGP SIGNATURE-----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=Hhge
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/machine-next-pull-request' into staging
Machine queue, 2018-05-07
* pc-dimm: factor out MemoryDevice
(virtio-pmem and virtio-mem will make use of the new abstraction later)
* scripts/device-crash-test: Removed fixed CAN entries
# gpg: Signature made Mon 07 May 2018 18:01:42 BST
# gpg: using RSA key 2807936F984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/machine-next-pull-request:
scripts/device-crash-test: Removed fixed CAN entries
vl: allow 'maxmem' without 'slot'
spapr: rename "hotplug memory" terminology to "device memory"
pc: rename "hotplug memory" terminology to "device memory"
machine: rename MemoryHotplugState to DeviceMemoryState
pc-dimm: move actual plug/unplug of a memory region to MemoryDevice
pc-dimm: factor out capacity and slot checks into MemoryDevice
pc-dimm: factor out address search into MemoryDevice code
pc-dimm: pass in the machine and to the MemoryHotplugState
pc-dimm: no need to pass the memory region
machine: make MemoryHotplugState accessible via the machine
pc-dimm: factor out MemoryDevice interface
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Several code cleanups, minor specification conformance changes,
fixes to make ROM read-only and add device-tree size checks.
* Honour privileged ISA v1.10 counter enable CSRs.
* Implements WARL behavior for CSRs that don't support writes
* Past behavior of raising traps was non-conformant
with the RISC-V Privileged ISA Specification v1.10.
* Allow S-mode access to sstatus.MXR when priv ISA >= v1.10
* Sets mtval/stval to zero on exceptions without addresses
* Past behavior of leaving the last value was non-conformant
with the RISC-V Privileged ISA Specition v1.10. mtval/stval
must be set on all exceptions; to zero if not supported.
* Make ROMs read-only and implement device-tree size checks
* Uses memory_region_init_rom and rom_add_blob_fixed_as
* Adds hexidecimal instruction bytes to disassembly output.
* Fixes missing break statement for rv128 disassembly.
* Several code cleanups
* Replacing hard-coded constants with enums
* Dead-code elimination
This is an incremental pull that contains 20 reviewed changes out
of 38 changes currently queued in the qemu-2.13-for-upstream branch.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQR8mZMOsXzYugc9Xvpr8dezV+8+TwUCWu496QAKCRBr8dezV+8+
T1ZEAJ4wQRHZtn4suN5yMEHQMA2FkX1iNACgiYWLtcNcgoa88eaTcJJJu4QZryY=
=I2wf
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/riscv/tags/riscv-qemu-2.13-pull-20180506' into staging
RISC-V: QEMU 2.13 Privileged ISA emulation updates
Several code cleanups, minor specification conformance changes,
fixes to make ROM read-only and add device-tree size checks.
* Honour privileged ISA v1.10 counter enable CSRs.
* Implements WARL behavior for CSRs that don't support writes
* Past behavior of raising traps was non-conformant
with the RISC-V Privileged ISA Specification v1.10.
* Allow S-mode access to sstatus.MXR when priv ISA >= v1.10
* Sets mtval/stval to zero on exceptions without addresses
* Past behavior of leaving the last value was non-conformant
with the RISC-V Privileged ISA Specition v1.10. mtval/stval
must be set on all exceptions; to zero if not supported.
* Make ROMs read-only and implement device-tree size checks
* Uses memory_region_init_rom and rom_add_blob_fixed_as
* Adds hexidecimal instruction bytes to disassembly output.
* Fixes missing break statement for rv128 disassembly.
* Several code cleanups
* Replacing hard-coded constants with enums
* Dead-code elimination
This is an incremental pull that contains 20 reviewed changes out
of 38 changes currently queued in the qemu-2.13-for-upstream branch.
# gpg: Signature made Sun 06 May 2018 00:27:37 BST
# gpg: using DSA key 6BF1D7B357EF3E4F
# gpg: Good signature from "Michael Clark <michaeljclark@mac.com>"
# gpg: aka "Michael Clark <mjc@sifive.com>"
# gpg: aka "Michael Clark <michael@metaparadigm.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 7C99 930E B17C D8BA 073D 5EFA 6BF1 D7B3 57EF 3E4F
* remotes/riscv/tags/riscv-qemu-2.13-pull-20180506:
RISC-V: Mark ROM read-only after copying in code
RISC-V: No traps on writes to misa,minstret,mcycle
RISC-V: Make mtvec/stvec ignore vectored traps
RISC-V: Add mcycle/minstret support for -icount auto
RISC-V: Use [ms]counteren CSRs when priv ISA >= v1.10
RISC-V: Allow S-mode mxr access when priv ISA >= v1.10
RISC-V: Clear mtval/stval on exceptions without info
RISC-V: Hardwire satp to 0 for no-mmu case
RISC-V: Update E and I extension order
RISC-V: Remove erroneous comment from translate.c
RISC-V: Remove EM_RISCV ELF_MACHINE indirection
RISC-V: Make virt header comment title consistent
RISC-V: Make some header guards more specific
RISC-V: Fix missing break statement in disassembler
RISC-V: Include instruction hex in disassembly
RISC-V: Remove unused class definitions
RISC-V: Remove identity_translate from load_elf
RISC-V: Use ROM base address and size from memmap
RISC-V: Make virt board description match spike
RISC-V: Replace hardcoded constants with enum values
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
qemu-system-ppc fails to build with GCC 8.0.1:
/home/hsp/src/qemu-master/hw/ppc/e500.c: In function ‘ppce500_load_device_tree’:
/home/hsp/src/qemu-master/hw/ppc/e500.c:442:37: error: ‘/pic@’
directive output may be truncated writing 5 bytes into a region of
size between 1 and 128 [-Werror=format-truncation=]
snprintf(mpic, sizeof(mpic), "%s/pic@%llx", soc, MPC8544_MPIC_REGS_OFFSET);
^~~~~
In file included from /usr/include/stdio.h:862,
from /home/hsp/src/qemu-master/include/qemu/osdep.h:68,
from /home/hsp/src/qemu-master/hw/ppc/e500.c:17:
/usr/include/bits/stdio2.h:64:10: note: ‘__builtin___snprintf_chk’
output between 11 and 138 bytes into a destination of size 128
return __builtin___snprintf_chk (__s, __n, __USE_FORTIFY_LEVEL - 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
__bos (__s), __fmt, __va_arg_pack ());
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/home/hsp/src/qemu-master/hw/ppc/e500.c:470:39: error:
‘/global-utilities@’ directive output may be truncated writing 18
bytes into a region of size between 1 and 128
[-Werror=format-truncation=]
snprintf(gutil, sizeof(gutil), "%s/global-utilities@%llx", soc,
^~~~~~~~~~~~~~~~~~
In file included from /usr/include/stdio.h:862,
from /home/hsp/src/qemu-master/include/qemu/osdep.h:68,
from /home/hsp/src/qemu-master/hw/ppc/e500.c:17:
/usr/include/bits/stdio2.h:64:10: note: ‘__builtin___snprintf_chk’
output between 24 and 151 bytes into a destination of size 128
return __builtin___snprintf_chk (__s, __n, __USE_FORTIFY_LEVEL - 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
__bos (__s), __fmt, __va_arg_pack ());
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/home/hsp/src/qemu-master/hw/ppc/e500.c:477:36: error: ‘/msi@’
directive output may be truncated writing 5 bytes into a region of
size between 0 and 127 [-Werror=format-truncation=]
snprintf(msi, sizeof(msi), "/%s/msi@%llx", soc, MPC8544_MSI_REGS_OFFSET);
^~~~~
In file included from /usr/include/stdio.h:862,
from /home/hsp/src/qemu-master/include/qemu/osdep.h:68,
from /home/hsp/src/qemu-master/hw/ppc/e500.c:17:
/usr/include/bits/stdio2.h:64:10: note: ‘__builtin___snprintf_chk’
output between 12 and 139 bytes into a destination of size 128
return __builtin___snprintf_chk (__s, __n, __USE_FORTIFY_LEVEL - 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
__bos (__s), __fmt, __va_arg_pack ());
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix this by converting e500 to use g_strdup_printf()+g_free() instead
of snprintf(). This is done globally, even for call sites that don't
break build, since this is the preferred practice in QEMU.
Reported-by: Howard Spoelstra <hsp.cat7@gmail.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 152568372989.443627.900708381919207053.stgit@bahia.lan
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's make it clear at relevant places that we are dealing with device
memory. That it can be used for memory hotplug is just a special case.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-11-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
[ehabkost: rebased series, solved conflicts at spapr.c]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Let's make it clear that we are dealing with device memory. That it can
be used for memory hotplug is just a special case.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-10-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename it to better match the new terminology.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-9-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Registering the memory region for migration has do be done by the owner.
There could be cases, where we don't want to migrate the memory.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-8-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the checks into memory_device_get_free_addr(). This will check
before doing any calculations if we have KVM/vhost slots left and if
the total region size would be exceeded.
Of course, while at it, make it independent of pc-dimm code.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-7-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This mainly moves code, but does a handfull of optimizations:
- We pass the machine instead of the address space properties
- We check the hinted address directly and handle fragmented memory
better
- We make the search independent of pc-dimm
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-6-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We use the machine internally either way, so let's just pass it in then.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-5-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We can just query it ourselves. When unplugging, we should always be
able to the region (as it was previously plugged). E.g. PPC already
assumed that and used &error_abort.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-4-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Let's allow to query the MemoryHotplugState directly from the machine.
If the pointer is NULL, the machine does not support memory devices. If
the pointer is !NULL, the machine supports memory devices and the
data structure contains information about the applicable physical
guest address space region.
This allows us to generically detect if a certain machine has support
for memory devices, and to generically manage it (find free address
range, plug/unplug a memory region).
We will rename "MemoryHotplugState" to something more meaningful
("DeviceMemory") after we completed factoring out the pc-dimm code into
MemoryDevice code.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-3-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
[ehabkost: rebased series, solved conflicts at spapr.c]
[ehabkost: squashed fix to use g_malloc0()]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
On the qmp level, we already have the concept of memory devices:
"query-memory-devices"
Right now, we only support NVDIMM and PCDIMM.
We want to map other devices later into the address space of the guest.
Such device could e.g. be virtio devices. These devices will have a
guest memory range assigned but won't be exposed via e.g. ACPI. We want
to make them look like memory device, but not glued to pc-dimm.
Especially, it will not always be possible to have TYPE_PC_DIMM as a parent
class (e.g. virtio devices). Let's use an interface instead. As a first
part, convert handling of
- qmp_pc_dimm_device_list
- get_plugged_memory_size
to our new model. plug/unplug stuff etc. will follow later.
A memory device will have to provide the following functions:
- get_addr(): Necessary, as the property "addr" can e.g. not be used for
virtio devices (already defined).
- get_plugged_size(): The amount this device offers to the guest as of
now.
- get_region_size(): Because this can later on be bigger than the
plugged size.
- fill_device_info(): Fill MemoryDeviceInfo, e.g. for qmp.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-2-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make sure we only ask the spice local renderer for display updates in
case we have a valid primary surface. Without that spice is confused
and throws errors in case a display update request (triggered by
screendump for example) happens in parallel to a mode switch and hits
the race window where the old primary surface is gone and the new isn't
establisted yet.
Cc: qemu-stable@nongnu.org
Fixes: https://bugzilla.redhat.com//show_bug.cgi?id=1567733
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180427115528.345-1-kraxel@redhat.com
usb-host emulates a device unplug after live migration, because the
device state is unknown and unplug/replug makes sure the guest
re-initializes the device into a working state. This can't be done in
post-load though, so post-load just schedules a bottom half which
executes after vmload is complete.
It can happen that the device autoscan timer hits the race window
between scheduling and running the bottom half, which in turn can
triggers an assert().
Fix that issue by just ignoring the usb_host_open() call in case the
bottom half didn't execute yet.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1572851
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180503062932.17233-1-kraxel@redhat.com
Currently, it's only being checked if desc is NULL and
so write support breaks upon specifying desc
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180503192028.14353-3-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
CID 1390578: In usb_mtp_write_metadata, parent can never be NULL but
just in case, add an assert
CID 1390592: Check for o->format only if o !=NULL
CID 1390604: Check s->data_out != NULL in usb_mtp_handle_data
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180503192028.14353-2-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The sifive_u machine already marks its ROM readonly however
it has the wrong base address for its mask ROM. This patch
fixes the sifive_u mask ROM base address.
This commit makes all other boards consistently use mask_rom
as the variable name for their ROMs. Boards that use device
tree now check that that the device tree fits in the assigned
ROM space using the new qemu_fdt_totalsize(void *fdt)
interface, adding a bounds check and error message. This
can detect truncation.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <Alistair.Francis@wdc.com>
Removes a whole lot of unnecessary boilerplate code. Machines
don't need to be objects. The expansion of the SOC object model
for the RISC-V machines will happen in the future as SiFive
plans to add their FE310 and FU540 SOCs to QEMU. However, it
seems that this present boilerplate is complete unnecessary.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
When load_elf is called with NULL as an argument to the
address translate callback, it does an identity translation.
This commit removes the redundant identity_translate callback.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Another case of replacing hard coded constants, this time
referring to the definition in the virt machine's memmap.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
This makes 'qemu-system-riscv64 -machine help' output more tidy
and consistent.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
The RISC-V device-tree code has a number of hard-coded
constants and this change moves them into header enums.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
ARM virt machine now exposes a new "iommu" option.
The SMMUv3 IOMMU is instantiated using -machine virt,iommu=smmuv3.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-15-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch builds the smmuv3 node in the ACPI IORT table.
The RID space of the root complex, which spans 0x0-0x10000
maps to streamid space 0x0-0x10000 in smmuv3, which in turn
maps to deviceid space 0x0-0x10000 in the ITS group.
The guest must feature the IOMMU probe deferral series
(https://lkml.org/lkml/2017/4/10/214) which fixes streamid
multiple lookup. This bug is not related to the SMMU emulation.
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Shannon Zhao <zhaoshenglong@huawei.com>
Message-id: 1524665762-31355-14-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Philippe Mathieu-Daudé