Not all bits in SMRAM and ESMRAMC can be changed by the guest.
Add wmask defines accordingly and set them in mch_reset().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The cache bits in ESMRAMC are hardcoded to 1 (=disabled) according to
the q35 mch specs. Add and use a define with this default.
While being at it also update the SMRAM default to use the name (no code
change, just makes things a bit more readable).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When H_SMRAME is 1, low memory at 0xa0000 is left alone by
SMM, and instead the chipset maps the 0xa0000-0xbffff window at
0xfeda0000-0xfedbffff. This affects both the "non-SMM" view controlled
by D_OPEN and the SMM view controlled by G_SMRAME, so add two new
MemoryRegions and toggle the enabled/disabled state of all four
in mch_update_smram.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's easier to inline it now that most of its work is done by the CPU
(rather than the chipset) through /machine/smram and the memory API.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove cpu_smm_register and cpu_smm_update. Instead, each CPU
address space gets an extra region which is an alias of
/machine/smram. This extra region is enabled or disabled
as the CPU enters/exits SMM.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This region is exported at /machine/smram. It is "empty" if
SMRAME=0 and points to SMRAM if SMRAME=1. The CPU will
enable/disable it as it enters or exits SMRAM.
While touching nearby code, the existing memory region setup was
slightly inconsistent. The smram_region is *disabled* in order to open
SMRAM (because the smram_region shows the low VRAM instead of the RAM
at 0xa0000). Because SMRAM is closed at startup, the smram_region must
be enabled when creating the i440fx or q35 devices.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This commit was generated mechanically by coccinelle from the following
semantic patch:
@@
expression val;
@@
- (ffs(val) - 1)
+ ctz32(val)
The call sites have been audited to ensure the ffs(0) - 1 == -1 case
never occurs (due to input validation, asserts, etc). Therefore we
don't need to worry about the fact that ctz32(0) == 32.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427124571-28598-5-git-send-email-stefanha@redhat.com
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It is not clear from the code how a 0 parameter should be handled by the
hardware. Keep the same behavior as ffs(0) - 1 == -1.
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427124571-28598-4-git-send-email-stefanha@redhat.com
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Switch all the uses of ld/st*_phys to address_space_ld/st*,
except for those cases where the address space is the CPU's
(ie cs->as). This was done with the following script which
generates a Coccinelle patch.
A few over-80-columns lines in the result were rewrapped by
hand where Coccinelle failed to do the wrapping automatically,
as well as one location where it didn't put a line-continuation
'\' when wrapping lines on a change made to a match inside
a macro definition.
===begin===
#!/bin/sh -e
# Usage:
# ./ldst-phys.spatch.sh > ldst-phys.spatch
# spatch -sp_file ldst-phys.spatch -dir . | sed -e '/^+/s/\t/ /g' > out.patch
# patch -p1 < out.patch
for FN in ub uw_le uw_be l_le l_be q_le q_be uw l q; do
cat <<EOF
@ cpu_matches_ld_${FN} @
expression E1,E2;
identifier as;
@@
ld${FN}_phys(E1->as,E2)
@ other_matches_ld_${FN} depends on !cpu_matches_ld_${FN} @
expression E1,E2;
@@
-ld${FN}_phys(E1,E2)
+address_space_ld${FN}(E1,E2, MEMTXATTRS_UNSPECIFIED, NULL)
EOF
done
for FN in b w_le w_be l_le l_be q_le q_be w l q; do
cat <<EOF
@ cpu_matches_st_${FN} @
expression E1,E2,E3;
identifier as;
@@
st${FN}_phys(E1->as,E2,E3)
@ other_matches_st_${FN} depends on !cpu_matches_st_${FN} @
expression E1,E2,E3;
@@
-st${FN}_phys(E1,E2,E3)
+address_space_st${FN}(E1,E2,E3, MEMTXATTRS_UNSPECIFIED, NULL)
EOF
done
===endit===
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Make address_space_rw take transaction attributes, rather
than always using the 'unspecified' attributes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
After commit 5312bd8 the bonito_readl() and bonito_writel() have been
accessing incorrect addresses. Consequently QEMU is crashing when trying
to boot Linux kernel on fulong2e machine.
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Fixes a QEMU crash when passing iommu parameter in command line.
Running
x86_64-softmmu/qemu-system-x86_64 -machine pc,iommu=on -enable-kvm
leads to crash:
qemu-system-x86_64: qemu/util/qemu-option.c:387: qemu_opt_get_bool_helper:
Assertion `opt->desc && opt->desc->type == QEMU_OPT_BOOL' failed.
Aborted (core dumped)
This happens because commit e79d5a6 ("machine: remove qemu_machine_opts global
list") removed the global option descriptions and moved them to MachineState's
QOM properties.
Fix this by querying machine properties through designated wrappers.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Convert the device models where initialization obviously can't fail.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
- RCU: fix MemoryRegion lifetime issues in PCI; document the rules;
convert of AddressSpaceDispatch and RAMList
- KVM: add kvm_exit reasons for aarch64
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJU4hugAAoJEL/70l94x66DZXEH/i72tOgvKZfAjfq2xmHXNEsr
roCfTFIIjKK7feyW6YgwT5pgex6I5umFsO+uIyI/wbu8nDl/3NYEQBT4fR2cGfli
GKeJOEu8kf+Zt8U+fbxyVQclbuU5S0Ujsg1fX4QXC4swB5fGLT2cRWJ5qd6hKBQs
GflBuLa7h4eOzcTtOPpqRIwZ8mQE0uxv/hKq9kYLKHXJN2aWsiOls8KQ2CXj2yAl
p6bMS5f0H0S/1hvQcQV9EazX7owlPIEet3AmSL1TC2sjJ8hrNGMBoFPtUys1uqjc
B3CwuGi0JtWIduFYV9vZ/Ze4G7Y2iZlqc5vDxIl94d+iFmoHymDOi3mFUZ3H8XQ=
=Lk9p
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
- vhost-scsi: add bootindex property
- RCU: fix MemoryRegion lifetime issues in PCI; document the rules;
convert of AddressSpaceDispatch and RAMList
- KVM: add kvm_exit reasons for aarch64
# gpg: Signature made Mon Feb 16 16:32:32 2015 GMT using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (21 commits)
Convert ram_list to RCU
exec: convert ram_list to QLIST
cosmetic changes preparing for the following patches
exec: protect mru_block with RCU
rcu: add g_free_rcu
rcu: introduce RCU-enabled QLIST
exec: RCUify AddressSpaceDispatch
exec: make iotlb RCU-friendly
exec: introduce cpu_reload_memory_map
docs: clarify memory region lifecycle
pci: split shpc_cleanup and shpc_free
pcie: remove mmconfig memory leak and wrap mmconfig update with transaction
memory: keep the owner of the AddressSpace alive until do_address_space_destroy
rcu: run RCU callbacks under the BQL
rcu: do not let RCU callbacks pile up indefinitely
vhost-scsi: set the bootable value of channel/target/lun
vhost-scsi: add a property for booting
vhost-scsi: expose the TYPE_FW_PATH_PROVIDER interface
vhost-scsi: add bootindex property
qdev: support to get a device firmware path directly
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Note that even after this patch, most callers of address_space_*
functions must still be under the big QEMU lock, otherwise the memory
region returned by address_space_translate can disappear as soon as
address_space_translate returns. This will be fixed in the next part
of this series.
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, keep current behaviour by always using get_system_memory().
Also use QOM casts when possible.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
With simple exposure of MMFG, ioport window, mmio window and an IRQ line we
can successfully create a workable PCIe host bridge that can be mapped anywhere
and only needs to get described to the OS using whatever means it likes.
This patch implements such a "generic" host bridge. It handles 4 legacy IRQ
lines. MSIs need to be handled external to the host bridge.
This device is particularly useful for the "pci-host-ecam-generic" driver in
Linux.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Tested-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The e500 PCI controller has configurable windows that allow a guest OS
to selectively map parts of the PCI bus space to CPU address space and
to selectively map parts of the CPU address space for DMA requests into
PCI visible address ranges.
So far, we've simply assumed that this mapping is 1:1 and ignored it.
However, the PCICSRBAR (CCSR mapped in PCI bus space) always has to live
inside the first 32bits of address space. This means if we always treat
all mappings as 1:1, this map will collide with our RAM map from the CPU's
point of view.
So this patch adds proper ATMU support which allows us to keep the PCICSRBAR
below 32bits local to the PCI bus and have another, different window to PCI
BARs at the upper end of address space. We leverage this on e500plat though,
mpc8544ds stays virtually 1:1 like it was before, but now also goes via ATMU.
With this patch, I can run guests with lots of RAM and not coincidently access
MSI-X mappings while I really want to access RAM.
Signed-off-by: Alexander Graf <agraf@suse.de>
- Build: fixing block/iscsi.so and ranlib warnings on Mac OS X
- Migration fixes for x86
- The odd KVM patch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=GIKW
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
- Memory: improve error reporting and avoid crashes on hotplug
- Build: fixing block/iscsi.so and ranlib warnings on Mac OS X
- Migration fixes for x86
- The odd KVM patch.
# gpg: Signature made Thu 11 Sep 2014 11:21:10 BST using RSA key ID 9B4D86F2
# gpg: Good signature from "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: aka "Paolo Bonzini <bonzini@gnu.org>"
* remotes/bonzini/tags/for-upstream: (21 commits)
gdbstub: init mon_chr through qemu_chr_alloc
pckbd: adding new fields to vmstate
mc146818rtc: add missed field to vmstate
piix: do not set irq while loading vmstate
serial: fixing vmstate for save/restore
parallel: adding vmstate for save/restore
fdc: adding vmstate for save/restore
cpu: init vmstate for ticks and clock offset
apic_common: vapic_paddr synchronization fix
vl: use QLIST_FOREACH_SAFE to visit change state handlers
exec: add parameter errp to gethugepagesize
exec: report error when memory < hpagesize
hostmem-ram: don't exit qemu if size of memory-backend-ram is way too big
memory: add parameter errp to memory_region_init_rom_device
memory: add parameter errp to memory_region_init_ram
exec: add parameter errp to qemu_ram_alloc and qemu_ram_alloc_from_ptr
rules.mak: Fix DSO build by pulling in archive symbols
util: Don't link host-utils.o if it's empty
util: Move general qemu_getauxval to util/getauxval.c
trace: Only link generated-tracers.o with "simple" backend
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch avoids setting an irq while loading the state of the ISA bridge.
Because the i8259 has not been deserialized yet, raising an interrupt
could bring the system out-of-sync with the migration source. For example,
the migration source could have masked the interrupt in the i8259. On the
destination, the i8259 device model would not know that yet and would
trigger an interrupt in the CPU.
This patch eliminates setting the irq and just restores the calculated
state fields in post_load function. Interrupt state will be deserialized
separately through the IRR field of the i8259.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add parameter errp to memory_region_init_ram and update all call sites
to pass in &error_abort.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both OpenBSD and FreeBSD SPARC64 attempt to read the interrupt map from the
hardware and will fail if the correct ino isn't present.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Add context-cache to cache context-entry encountered on a page-walk. Each
VTDAddressSpace has a member of VTDContextCacheEntry which represents an entry
in the context-cache. Since devices with different bus_num and devfn have their
respective VTDAddressSpace, this will be a good way to reference the cached
entries.
Each VTDContextCacheEntry will have a context_cache_gen and the cached entry
is valid only when context_cache_gen equals IntelIOMMUState.context_cache_gen.
Signed-off-by: Le Tan <tamlokveer@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fix coding style issues around in hw/pci-host/q35.c and hw/core/machine.c.
Signed-off-by: Le Tan <tamlokveer@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add Intel IOMMU emulation to q35 chipset and expose it to the guest.
1. Add a machine option. Users can use "-machine iommu=on|off" in the command
line to enable/disable Intel IOMMU. The default is off.
2. Accroding to the machine option, q35 will initialize the Intel IOMMU and
use pci_setup_iommu() to setup q35_host_dma_iommu() as the IOMMU function for
the pci bus.
3. q35_host_dma_iommu() will return different address space according to the
bus_num and devfn of the device.
Signed-off-by: Le Tan <tamlokveer@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a bool variable is_write as a parameter to the translate function of
MemoryRegionIOMMUOps to indicate the operation of the access. It can be
used for correct fault reporting from within the callback.
Change the interface of related functions.
Signed-off-by: Le Tan <tamlokveer@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* remotes/mcayland/qemu-sparc:
target-sparc64: implement Short Floating-Point Store Instructions
apb: add IOMMU flush register implementation
sun4u: switch second PCI-ebus bridge BAR over to PCI IO space
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The IOMMU flush register is a write-only register used to remove entries from the
hardware TLB. Allow guest writes to this register as a no-op, and return a value
of 0 for reads.
This fixes IOMMU DMA operations under NetBSD SPARC64.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
piix_pci.c has been renamed into piix.c at commit
c0907c9e64
update the obsolete reference.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Fix PCI hole size to match that what is found on real hardware.
(OpenBIOS already uses the correct length.)
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Alexander Graf <agraf@suse.de>
The array regs is declared with IOMMU_NREGS (3) elements and accessed
using IOMMU_CTRL (0) and IOMMU_BASE (8). In most cases, those values
are right shifted before being used as an index which results in indices
0 and 1. In one case, this right shift was missing for IOMMU_BASE which
results in an out-of-bounds write access with index 8.
The patch adds the missing shift operation also for IOMMU_CTRL where
it is needed only for cosmetic reasons.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fix a typo in the ppce500_pci vmstate definition which meant that
we were migrating the struct pci_inbound using the vmstate for
pci_outbound. Fortunately the two structures have exactly the same
format at the moment (four uint32_ts) so this was harmless, and
we can correcting the typo without a migration compatibility
break because the vmstate name doesn't go out on the wire.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds pci pin to irq_num routing callback.
This callback is called from pci_device_route_intx_to_irq to
find which pci device maps to which irq.
This fix is required for pci-device passthrough using vfio.
Also without this patch we gets below prints
"
PCI: Bug - unimplemented PCI INTx routing (e500-pcihost)
qemu-system-ppc64: PCI: Bug - unimplemented PCI INTx routing (e500-pcihost) "
and Legacy interrupt does not work with pci device passthrough.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
[agraf: remove double semicolon]
Signed-off-by: Alexander Graf <agraf@suse.de>
- Use PCI_NUM_PINS rather than hardcoding
- use "pin" wherever possible
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
* remotes/mcayland/qemu-sparc:
apb: implement IOMMU translation for PCI host bridge
apb: handle reading/writing of IOMMU control registers
apb: fix IOMMU register sizes
apb: Move IOMMU registers into a separate IOMMUState struct
tcx: move initialisation from realizefn to initfn
tcx: move initialisation from SysBusDevice class to TCX class realizefn
cg3: add extra check to prevent CG3 register array overflow
cg3: move initialisation from realizefn to initfn
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While the registers are documented as being 64-bit, Linux seems to access
them in two halves as 2 x 32-bit accesses. Make sure that we can correctly
handle this case.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
According to the referenced documentation, the IOMMU has 3 64-bit registers
consisting of a control register, base register and flush register.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This assures the trivial field initialization is applied for any derived
type - currently only Q35PCIHost.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
The raven_io_read() and raven_io_write() functions pass and
return values in little-endian format (since the IO op struct
is marked DEVICE_LITTLE_ENDIAN); however they were storing the
values in the buffer to pass to address_space_read/write()
in host-endian order, which meant that on big-endian hosts
the values were inadvertently reversed. Use the *_le_p()
accessors instead so that we are consistent regardless of
host endianness.
Strictly speaking the byte order of the buffer for
address_space_rw() is target byte order (which for PPC
will be BE) but it doesn't actually matter as long as we
are consistent about the marking on the IO op struct and
which stl_*_p().
This bug was probably introduced due to confusion caused by
the two different versions of ldl_p() and friends:
bswap.h defines versions meaning "host endianness access"
cpu-all.h defines versions meaning "target endianness access"
As a target-independent source file prep.c gets the bswap.h
versions; the very similar looking code in ioport.c is
compiled per-target and gets the cpu-all.h versions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1396972271-22660-1-git-send-email-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <rth@twiddle.net>
This has been tested on Linux 2.4/PPC with the lsi53c895a SCSI adapter.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
PCI memory region is 0x3f000000 bytes starting at 0xc0000000.
However, keep compatibility with Open Hack'Ware expectations
by adding a hack for Open Hack'Ware display.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
PCI I/O region is 0x3f800000 bytes starting at 0x80000000.
Do not use global QEMU I/O region, which is only 64KB.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Remove now duplicated code from prep board.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Regions added subsequently will also have the pci_ prefix.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Raven datasheet explains where firmware lives in system memory, so do
it there instead of in board code. Other boards using the same PCI
host will not have to copy the firmware loading code.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
[AF: Drop BIOS size workaround in favor of replacing our firmware blob]
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
In write-only mode, writes are forwarded to RAM, while reads should not be
handled (ie should return 0xff).
Assume that in this mode, no read access is ever done, as they shouldn't
give any sensible result.
So, in write-only mode, alias PAM region to RAM, instead of PCI memory
(which can even be mapped to some device!)
This fixes Award BIOS, which use this mode to shadow system BIOS and video BIOS.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Most changes here are hotplug related:
This merges hotplug infrastructure changes by Igor,
some acpi related fixes, and PC fixes.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJS+Jg2AAoJECgfDbjSjVRp2hIH/3PezOqYAJlp1LzHPYgTII5R
ZWdlHWJODB5QKGuDnJ0rKTZn+9n4f27Q7ynwqrodrLNtzglfmPUwtjTb52vbd1yh
qJ7BtvGIewUEjTPVs2feipb75jFZFhvIU46F1jPJAiaNKG0nl6zwVHn5XfFqesv2
4TlHAoqYvpUUuFcG7Qu+hREUrjb/tdxwP8EYM4qDPOSxguS2R2+3/17BVlPDQGia
bKl6j5EmnmmbQ0h8Sepy3YKh9d1rZnKFsolMFrL8ITjzEzzyKjpE284GNe/5eY25
HR25dY5eYTb0d3QPeH2O5sOrZgOFpTZc8WOo9Kxi0OTjWxFoZstZ1AOM3A2DAoY=
=EtLZ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi,pc,pci fixes and enhancements
Most changes here are hotplug related:
This merges hotplug infrastructure changes by Igor,
some acpi related fixes, and PC fixes.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon 10 Feb 2014 09:13:26 GMT using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
ACPI: Remove commented-out code from HPET._CRS
hw/pci: switch to a generic hotplug handling for PCIDevice
pci/pcie: convert PCIE hotplug to use hotplug-handler API
pci/shpc: convert SHPC hotplug to use hotplug-handler API
acpi/piix4pm: convert ACPI PCI hotplug to use hotplug-handler API
qdev:pci: refactor PCIDevice to use generic "hotpluggable" property
hw/acpi: move typeinfo to the file end
qdev: add "hotpluggable" property to Device
qdev: add to BusState "hotplug-handler" link
define hotplug interface
loader: document that errno is set
pc.c: better error message on initrd sizing failure
pc_piix: enable legacy hotplug for Xen
qtest: don't report signals if qtest driver enabled
hw:piix4:acpi: reuse pcihp code for legacy PCI hotplug
pcihp: remove unused AcpiPciHpPciStatus.device_present field
pcihp: make pci_read() mmio calback compatible with legacy ACPI hotplug
pcihp: make PCI hotplug mmio handlers indifferent to PCI_HOTPLUG_ADDR
pcihp: replace enable|disable_device() with oneliners
pcihp: reduce number of device check events
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Get rid of PCIDevice specific PCIDeviceClass.no_hotplug and use
generic DeviceClass.hotpluggable field instead.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This includes some Preparatory patches for cpu hotplug for q25 and memory
hotplug by Igor, tests and memory mapping change
by Laszlo and pci reset cleanup by Paolo.
There are also some fixes for fedora and virtio:
included here since they are test blockers for me.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSuF+2AAoJECgfDbjSjVRpTz0IAJhNCC8L2GVt+pm1RAt6lbqZ
u9bCrqfThDORN2mUTEuLu4ZpZC0DYc7d0Jjr5NPesC5G/Afzi5/to6+l7nNZneU3
OdBPglXCCfU/cRaLu7JG2akpha0GVU0tsSCoWIYa6mwlWA4/DXVMgeKg/bh/EgfM
B1w4fE2RgRM9bEqWmX4+tZw8dgk7uVJhu95HCDnb5eikaKlFzwuOlvexrDV3KbPc
bkJe35zbGrKOws93tiSeoqcDx2dcYSzecPoJ0jiCY0KXJ17PBWAvuLTtYqkwwe9J
2FEnTslQJ3Rc8jTFiOPWx2pGaejG4y7Tnk6uuzW6fbbSLOQDPJy3KgmutJFMt1A=
=ShCj
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
acpi,pci,pc,fedora,virtio fixes and enhancements
This includes some Preparatory patches for cpu hotplug for q25 and memory
hotplug by Igor, tests and memory mapping change
by Laszlo and pci reset cleanup by Paolo.
There are also some fixes for fedora and virtio:
included here since they are test blockers for me.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon 23 Dec 2013 08:07:18 AM PST using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
* mst/tags/for_anthony:
target-arm: fix build with gcc 4.8.2
virtio: add back call to virtio_bus_device_unplugged
piix: fix 32bit pci hole
qdev: switch reset to post-order
qdev: allow both pre- and post-order vists in qdev walking functions
pci: clean up resetting of IRQs
pci: do not export pci_bus_reset
ACPI/DSDT-CPU: cleanup bogus comment
ACPI: Q35 DSDT: fix CPU hotplug GPE0.2 handler
acpi: ich9: allow guest to clear SCI rised by GPE
acpi: factor out common pm_update_sci() into acpi core
acpi: piix4: remove not needed GPE0 mask
i440fx-test: verify firmware under 4G and 1M, both -bios and -pflash
i440fx-test: generate temporary firmware blob
i440fx-test: give each GTest case its own qtest
i440fx-test: qtest_start() should be paired with qtest_end()
hw/i386/pc_sysfw: support two flash drives
pc_piix: document gigabyte_align
piix: gigabyte alignment for ram
Message-id: 1387815007-1272-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Make the 32bit pci hole start at end of ram, so all possible address
space is covered.
We used to try and make addresses aligned so they are easier to cover
with MTRRs, but since they are cosmetic on KVM, this is probably not
worth worrying about.
Of course the firmware can use less than that. Leaving space unused is
no problem, mapping pci bars outside the hole causes problems though.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A PIIX3/PIIX4 southbridge has multiple functions. We model each
function as a separate qdev. Two of them need some special wiring set
up in pc_init1() or mips_malta_init() to work: the ISA bridge at 01.0,
and the SMBus controller at 01.3.
The IDE controller at 01.1 (piix3-ide, piix3-ide-xen, piix4-ide) has
always had cannot_instantiate_with_device_add_yet set, but there is no
obvious reason why device_add could not work for them. Drop it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Many PCI host bridges consist of a sysbus device and a PCI device.
You need both for the thing to work. Arguably, these bridges should
be modelled as a single, composite devices instead of pairs of
seemingly independent devices you can only use together, but we're not
there, yet.
Since the sysbus part can't be instantiated with device_add, yet,
permitting it with the PCI part is useless. We shouldn't offer
useless options to the user, so let's set
cannot_instantiate_with_device_add_yet for them.
It's already set for Bonito, Grackle, i440FX and Raven. Document why.
Set it for the others: dec-21154, e500-host-bridge, gt64120_pci, mch,
pbm-pci, ppc4xx-host-bridge, sh_pci_host, u3-agp, uni-north-agp,
uni-north-internal-pci, uni-north-pci, and versatile_pci_host.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
device_add plugs devices into suitable bus. For "real" buses, that
actually connects the device. For sysbus, the connections need to be
made separately, and device_add can't do that. The device would be
left unconnected, and could not possibly work.
Quite a few, but not all sysbus devices already set
cannot_instantiate_with_device_add_yet in their class init function.
Set it in their abstract base's class init function
sysbus_device_class_init(), and remove the now redundant assignments
from device class init functions.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
In an ideal world, machines can be built by wiring devices together
with configuration, not code. Unfortunately, that's not the world we
live in right now. We still have quite a few devices that need to be
wired up by code. If you try to device_add such a device, it'll fail
in sometimes mysterious ways. If you're lucky, you get an
unmysterious immediate crash.
To protect users from such badness, DeviceClass member no_user used to
make device models unavailable with -device / device_add, but that
regressed in commit 18b6dad. The device model is still omitted from
help, but is available anyway.
Attempts to fix the regression have been rejected with the argument
that the purpose of no_user isn't clear, and it's prone to misuse.
This commit clarifies no_user's purpose. Anthony suggested to rename
it cannot_instantiate_with_device_add_yet_due_to_internal_bugs, which
I shorten somewhat to keep checkpatch happy. While there, make it
bool.
Every use of cannot_instantiate_with_device_add_yet gets a FIXME
comment asking for rationale. The next few commits will clean them
all up, either by providing a rationale, or by getting rid of the use.
With that done, the regression fix is hopefully acceptable.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
There's no good reason to call our bus "pci" rather than let the default
bus name take over ("pci.0").
The big downside to calling it different from anyone else is that tools
that pass -device get confused. They are looking for a bus "pci.0" rather
than "pci".
To make life easier for everyone, let's just drop the name override.
Signed-off-by: Alexander Graf <agraf@suse.de>
With a help of negative memory region priority PCI address space
is mapped underneath RAM regions effectively catching every access
to addresses not mapped by any other region.
It simplifies PCI address space mapping into system address space.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
The following commit introduced a migration incompatibility:
commit 568f0690fd
Author: David Gibson <david@gibson.dropbear.id.au>
Date: Thu Jun 6 18:48:49 2013 +1000
pci: Replace pci_find_domain() with more general pci_root_bus_path()
The issue is that i440fx savevm idstr went from 0000:00:00.0/I440FX to
0000:00.0/I440FX. Unfortunately we are stuck with the breakage for
1.6 machine types.
Add a compat property to maintain the busted idstr for the 1.6 machine
types, but revert to the old style format for 1.7+, and <= 1.5.
Tested with migration from qemu 1.5, qemu 1.6, and qemu.git.
Cc: qemu-stable@nongnu.org
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This includes some pretty big changes:
- pci master abort support by Marcel
- pci IRQ API rework by Marcel
- acpi generation support by myself
Everything has gone through several revisions, latest versions have been on
list for a while without any more comments, tested by several
people.
Please pull for 1.7.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSXNO8AAoJECgfDbjSjVRp7VAH/0B73mCOiyVACGx7fazK3SGK
X8TxZWVtG5A77ISqKyrtjLAhK9DCQjEzQTbMNhXHM3Ar6crwo7nJZnQvH2Gh1X2p
34BOQSVc4rtXz5pwDIr48dBLrxeslwXub79chUs+IK1/4RSn3h3nuS3k6JVkmLJN
rcHMj4ljJmi4Hd9vOpmS1jo/a61usi36hhU7CMgcrsXzStZycBBzCozOB3VW8p1X
/iwyf91YjmNPkn9gA3/aViGjszu8jE91dkA0C+ljwvcGbs2yEl3LCWEJfsMvoh5P
2M+k0XXbHwq/P9PFMa/2/lWOo4EO4Oxa+G/6QvovJrteYnktr+E9DqjU8pCT7yI=
=CVfs
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pci, pc, acpi fixes, enhancements
This includes some pretty big changes:
- pci master abort support by Marcel
- pci IRQ API rework by Marcel
- acpi generation support by myself
Everything has gone through several revisions, latest versions have been on
list for a while without any more comments, tested by several
people.
Please pull for 1.7.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 15 Oct 2013 07:33:48 AM CEST using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
* mst/tags/for_anthony: (39 commits)
ssdt-proc: update generated file
ssdt: fix PBLK length
i386: ACPI table generation code from seabios
pc: use new api to add builtin tables
acpi: add interface to access user-installed tables
hpet: add API to find it
pvpanic: add API to access io port
ich9: APIs for pc guest info
piix: APIs for pc guest info
acpi/piix: add macros for acpi property names
i386: define pc guest info
loader: allow adding ROMs in done callbacks
i386: add bios linker/loader
loader: use file path size from fw_cfg.h
acpi: ssdt pcihp: updat generated file
acpi: pre-compiled ASL files
acpi: add rules to compile ASL source
i386: add ACPI table files from seabios
q35: expose mmcfg size as a property
q35: use macro for MCFG property name
...
Message-id: 1381818560-18367-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
This adds APIs that will be used to fill in
acpi tables, implemented using QOM,
to various ich9 components.
Some information is still missing in QOM,
so we fall back on lookups by type instead.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This adds APIs that will be used to fill in guest acpi tables.
Some required information is still lacking in QOM, so we
fall back on lookups by type and returning explicit types.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Address is already exposed, expose size for symmetry.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Useful to make it accessible through QOM.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This includes pc and pci cleanups and enhancements,
and a virtio-net bugfix related to softmac programming.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSR83kAAoJECgfDbjSjVRpX08H/jKgYBNJaChev1TROIVHEGbu
IzvkjfocvKO+6wmhOf5x+xwFmzrijUMa1CPvOkCp8c2A3Iek7rmnedknlhXYh7dM
z5mXcvFGjnu7ST38ydF/Emk9+Z6rRg5Y/hkmlDyr+9lNcoiCDLXXcUrKjeIHNoWl
e8w3yiPCJ528QyrLwQ890XetJphv67pMlsjMgLQ2betMk++Ac/ctUf1D2p1X4NeQ
Q2drbo5Z4yDk0i6QMA3iLq1Bh/AhE10bCDq9rCzfZGIKVyncL6ne2pSi/xDvpLrF
dmxoiJ5QrK6xLnagCcn5T6SB9DkwbEPdL7qCqlxZ8USr7cVyPdzYtHtGSBWdeXY=
=xF01
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pc,pci,virtio fixes and cleanups
This includes pc and pci cleanups and enhancements,
and a virtio-net bugfix related to softmac programming.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sun 29 Sep 2013 01:51:16 AM CDT using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
# By Michael S. Tsirkin (8) and others
# Via Michael S. Tsirkin
* mst/tags/for_anthony:
smbios: Factor out smbios_maybe_add_str()
smbios: Make multiple -smbios type= accumulate sanely
smbios: Improve diagnostics for conflicting entries
smbios: Convert to QemuOpts
smbios: Normalize smbios_entry_add()'s error handling to exit(1)
virtio-net: fix up HMP NIC info string on reset
pci: remove explicit check to 64K ioport size
piix4: disable io on reset
piix: use 64 bit window programmed by guest
q35: use 64 bit window programmed by guest
pci: add helper to retrieve the 64-bit range
range: add min/max operations on ranges
range: add Range to typedefs
q35: make pci window address/size match guest cfg
Message-id: 1380437951-21788-1-git-send-email-mst@redhat.com
For Q35, MMCFG address and size are guest configurable.
Update w32 property to make it behave accordingly.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This includes pc and pci cleanups and enhancements,
and a virtio bugfix for level interrupts.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSIveoAAoJECgfDbjSjVRp2C8IAL7DE0oM0jfEB5DAd8jlULHx
hA8RP21rFzyU8PwtHB+72+C1ImldBge4hvhI+qbsm6PoW3RCeV/lbESIRTiv8dCO
pGUOFmv8MfJAH+WWFsle5mRisoTksYQWWBMHCOqvmaY4JL9pBQOhCLHVhV1XfjtL
hO7uGrWmlijeILv5CxYyPMYuOEdVvRSZKzE+Fp2YKfNstiQrS5fJIlqmwCHrlneW
l2atnt2d9ZV1K8QYiGg4GRVbSAMJvA1wum+0F4gnXIz9yAeOt+Ht1s8cNKQDMouJ
r2OyVgPM9aS/XaO6ejct1Sjo7Vgh/Ublrpw3lFqV/qHix6rEHwy2I3JHFEJPjvk=
=SytJ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pc,pci,virtio fixes and cleanups
This includes pc and pci cleanups and enhancements,
and a virtio bugfix for level interrupts.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sun 01 Sep 2013 03:15:36 AM CDT using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
# By Michael S. Tsirkin (3) and others
# Via Michael S. Tsirkin
* mst/tags/for_anthony:
virtio_pci: fix level interrupts with irqfd
pc: reduce duplication, fix PIIX descriptions
hw: Clean up bogus default boot order
pci: add config space access traces
pc: fix regression for 64 bit PCI memory
pci: Introduce helper to retrieve a PCI device's DMA address space
Message-id: 1378023590-11109-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
To be passed on to object_initialize_with_type().
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> (virtio-ccw)
Signed-off-by: Andreas Färber <afaerber@suse.de>
commit 3984890181
pc: limit 64 bit hole to 2G by default
introduced a way for management to control
the window allocated to the 64 bit PCI hole.
This is useful, but existing management tools do not know how to set
this property. As a result, e.g. specifying a large ivshmem device with
size > 4G is broken by default. For example this configuration no
longer works:
-device ivshmem,size=4294967296,chardev=cfoo
-chardev socket,path=/tmp/sock,id=cfoo,server,nowait
Fix this by detecting that hole size was not specified
and defaulting to the backwards-compatible value of 1 << 62.
Cc: qemu-stable@nongnu.org
Cc: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently, it is done by i82378 PCI-ISA bridge, which shouldn't
care about it.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
It turns out that some 32 bit windows guests crash
if 64 bit PCI hole size is >2G.
Limit it to 2G for piix and q35 by default.
User may override default 64-bit PCI hole size by
using "pci-hole64-size" property.
Examples:
-global i440FX-pcihost.pci-hole64-size=4G
-global q35-pcihost.pci-hole64-size=4G
Reported-by: Igor Mammedov <imammedo@redhat.com>,
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Message-id: 1375109277-25561-8-git-send-email-imammedo@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
It isn't used anywhere else.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Message-id: 1375109277-25561-4-git-send-email-imammedo@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Message-id: 1375109277-25561-3-git-send-email-imammedo@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Introduce TYPE_PCI_BRIDGE as base type and use PCI_BRIDGE() casts.
Reviewed-by: Don Koch <dkoch@verizon.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
[AF: Updated pbm-bridge parent to TYPE_PCI_BRIDGE]
Signed-off-by: Andreas Färber <afaerber@suse.de>
The category will be used to sort the devices displayed in
the command line help.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Message-id: 1375107465-25767-4-git-send-email-marcel.a@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
... by making apb a subclass of TYPE_PCI_HOST_BRIDGE.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Message-id: 1374501278-31549-21-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This fixes endianness bugs in I/O port access.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Message-id: 1374501278-31549-13-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This board is little-endian, but still isa_mmio should die. :)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Message-id: 1374501278-31549-12-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
And split off MemoryRegion initialization into instance_init.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
And remove variables if possible.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
[AF: Converted remaining access and renamed to parent_obj]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
[AF: Converted remaining accesses and renamed to parent_obj]
Signed-off-by: Andreas Färber <afaerber@suse.de>
This includes some pci enhancements:
Better support for systems with multiple PCI root buses
FW cfg interface for more robust pci programming in BIOS
Minor fixes/cleanups for fw cfg and cross-version migration -
because of dependencies with other patches
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJR2ctmAAoJECgfDbjSjVRpQpAH/Rk00yLrQ2R5ScNa8AL9LeaJ
gVFndBmmuRz4gdhyATx6lzR98ic32iTr0+YR5mL51btgmM5a0bEd/SIu34nXriWj
PsM0wdXfo/oEygdttxhvzJOH17tohRV9xg2WA2d8BEwDzrDyqoQ4J0VJlHlG7u3W
nq4KVDVUpLNQFKG8ZgJ2vW0WMw/mBSj2rluhQUALhcuvChphtvAFZ2rsSfJr6bzD
aBELrtIvfLvPGN/0WVeYs9qlp4EE03H3X6gN61QvV3/YElxubKUV5XyMDOX2dW3D
2j0NQi84LYHn0SFap2r/Kgm47/F6Q56SFk5lrgZrg60mhQTwocw7PfL8CGxjXRI=
=gxxc
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pci,misc enhancements
This includes some pci enhancements:
Better support for systems with multiple PCI root buses
FW cfg interface for more robust pci programming in BIOS
Minor fixes/cleanups for fw cfg and cross-version migration -
because of dependencies with other patches
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sun 07 Jul 2013 03:11:18 PM CDT using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
# By David Gibson (10) and others
# Via Michael S. Tsirkin
* mst/tags/for_anthony:
pci: Fold host_buses list into PCIHostState functionality
pci: Remove domain from PCIHostBus
pci: Simpler implementation of primary PCI bus
pci: Add root bus parameter to pci_nic_init()
pci: Add root bus argument to pci_get_bus_devfn()
pci: Replace pci_find_domain() with more general pci_root_bus_path()
pci: Use helper to find device's root bus in pci_find_domain()
pci: Abolish pci_find_root_bus()
pci: Move pci_read_devaddr to pci-hotplug-old.c
pci: Cleanup configuration for pci-hotplug.c
pvpanic: fix fwcfg for big endian hosts
pvpanic: initialization cleanup
MAINTAINERS: s/Marcelo/Paolo/
e1000: cleanup process_tx_desc
pc_piix: cleanup init compat handling
pc: pass PCI hole ranges to Guests
pci: store PCI hole ranges in guestinfo structure
range: add Range structure
Message-id: 1373228271-31223-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
pci_find_domain() is used in a number of places where we want an id for a
whole PCI domain (i.e. the subtree under a PCI root bus). The trouble is
that many platforms may support multiple independent host bridges with no
hardware supplied notion of domain number.
This patch, therefore, replaces calls to pci_find_domain() with calls to
a new pci_root_bus_path() returning a string. The new call is implemented
in terms of a new callback in the host bridge class, so it can be defined
in some way that's well defined for the platform. When no callback is
available we fall back on the qbus name.
Most current uses of pci_find_domain() are for error or informational
messages, so the change in identifiers should be harmless. The exception
is pci_get_dev_path(), whose results form part of migration streams. To
maintain compatibility with old migration streams, the PIIX PCI host is
altered to always supply "0000" for this path, which matches the old domain
number (since the code didn't actually support domains other than 0).
For the pseries (spapr) PCI bridge we use a different platform-unique
identifier (pseries machines can routinely have dozens of PCI host
bridges). Theoretically that breaks migration streams, but given that we
don't yet have migration support for pseries, it doesn't matter.
Any other machines that have working migration support including PCI
devices will need to be updated to maintain migration stream compatibility.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Looks like dec.c is in pci-host by mistake.
Moving it over to pci-bridge.
Acked-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCI host bridges need to set fw_name to be discoverable
by bios for boot device selection.
In particular, seabios expects root device to be called
"/pci/@i0cf8", so let's set it up like that for Q35.
Cc: qemu-stable@nongnu.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Amos Kong <akong@redhat.com>
Although we try our best to automatically detect broken versions
of Linux which assume the old broken IRQ mapping we used to implement
for our model of the Versatile PCI controller, it turns out that
some particularly new kernels manage to outwit the autodetection.
We therefore provide a property for enabling the old broken IRQ
mapping, so that if users happen to have such a kernel they can
work around its deficiencies with the command line option:
-global versatile_pci.broken-irq-mapping=1
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1368545616-22344-4-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Newer versatilepb kernels still don't get the IRQ mapping right
for the PCI controller, but they get it differently wrong (they add
a fixed +64 offset to everything they write to PCI_INTERRUPT_LINE).
Update the autodetection to handle these too, and include a more
detailed comment on the various different behaviours that might
be present.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1368545616-22344-3-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit 5f37ef92b7.
It turns out that some kernels incorrectly depend on the
old QEMU behaviour of not putting the host PCI bridge device
where the hardware puts it, because they use a swizzling IRQ
mapping which is incorrect but happens to match up with old
broken QEMU when the slot number mod 4 is zero. Since we
start PCI devices at 11, if we put the host bridge at 29
then the first real PCI device goes at 11 and doesn't work.
Not putting the host bridge at 29 means it defaults to 11,
so the first real PCI device is at 12 and works.
Since continuing with the old behaviour doesn't cause problems
for kernels which do work with hardware, the simplest fix for
this is to revert the change.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1368545616-22344-2-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Every PCI Slot in PBM has 4 directly mapped IRQ lines.
Use the IRQ routing schema 0bssnn (Bus, Slot, interrupt Number)
described in Section 19.3.3 of UltraSPARC™-IIi User's Manual.
Please note that this patch requires the OpenBIOS counterpart patch.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
- clear interrupts only on writing to the interrupt clear registers
- don't overwrite a currently active interrupt request
- use the correct addresses for the interrupt clear registers
(section 19.3.3.3 of the UltraSPARC™-IIi User’s Manual)
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
According to UltraSPARC™-IIi User’s Manual, PBM has 64 IRQ lines.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Drop the vpb_pci_config_addr() function -- it is unnecessary since
the size of the memory regions means the hwaddr is always within
the 24 bit size. (This function was probably a leftover from when
read/write functions were called with absolute addresses rather
than relative ones.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paul Brook <paul@codesourcery.com>
The VersatilePB's PCI controller exposes the PCI memory space to the
system via three regions controlled by the mapping control registers.
Implement this so that guests can actually use MMIO-BAR PCI cards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paul Brook <paul@codesourcery.com>
The versatile_pci PCI controller has a set of control registers which
handle the mapping between PCI and system address spaces. Implement
these registers (though for now they have no effect since we don't
implement mapping PCI space into system memory at all).
The most natural order for our sysbus regions has the control
registers at the start, so move all the others down one.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paul Brook <paul@codesourcery.com>
Implement the correct IRQ mapping for the Versatile PCI controller; it
differs between realview and versatile boards, but the previous QEMU
implementation was correct only for the first PCI card on a versatile
board, since we weren't swizzling IRQs based on the slot number.
Since this change would otherwise break any uses of PCI on Linux kernels
which have an equivalent bug (since they have effectively only been
tested against QEMU, not real hardware), we implement a mechanism
for automatically detecting those broken kernels and switching back
to the old mapping. This works by looking at the values the kernel
writes to the PCI_INTERRUPT_LINE register in the config space, which
is effectively the interrupt number the kernel expects the device
to be using.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On real hardware the host bridge appears as a PCI device in slot 29,
so make QEMU put its host bridge in that slot too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paul Brook <paul@codesourcery.com>
Rather than overloading the system I/O space (which doesn't even make
any sense on ARM) for PCI I/O, create an memory region in the PCI
controller and use that to represent the I/O space.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paul Brook <paul@codesourcery.com>
Change versatile_pci to subclass TYPE_PCI_HOST_BRIDGE and generally
handle PCI in a more QOM-like fashion.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paul Brook <paul@codesourcery.com>
Update the Versatile PCI controller to use a realize function rather
than SysBusDevice::init. To reflect the fact that the 'realview_pci'
class is taking most of its implementation from 'versatile_pci' (and
to make the QOM casts work) we make 'realview_pci' a subclass of
'versatile_pci'.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paul Brook <paul@codesourcery.com>
Comments in the QEMU source code claim that the version of the PCI
controller on the VersatilePB board doesn't support the PCI I/O
region, but this is incorrect; expose that region, map it in the
correct location, and drop the misleading comments.
This change removes the only currently implemented difference
between the realview-pci and versatile-pci models; however there
are other differences in not-yet-implemented functionality, so we
retain the distinction between the two device types.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paul Brook <paul@codesourcery.com>
There is just one line in this source file with a hardcoded tab
indent, so just fix it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paul Brook <paul@codesourcery.com>