The alignment field is now set to the value that is promised to the
guest, rather than required by the host. The next patches will make
QEMU aware of the host-provided values, so make this clear.
The alignment is also not about memory buffers, but about the sectors on
the disk, change the documentation of the field.
At this point, the field is set by the device emulation, but completely
ignored by the block layer.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Propagate the error return value from get_indirect(). This bug was
introduced in commit 4d684832 ("vring: create a common function to parse
descriptors").
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch uses inbound GPIO lines (IRQ and FIR) for
interrupts instead of using the old pic_cpu method,
which doesn't correspond to real hardware.
This creates the CPU's inbound IRQ and FIR GPIO lines and
updates the Microblaze boards to use this new method.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Suggested-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reveiwed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
* bonzini/scsi-next:
scsi-disk: add UNMAP limits to block limits VPD page
block/iscsi: use a bh to schedule co reentrance
Message-id: 1387720926-11421-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
* stefanha/block:
commit: Remove unused check
qemu-iotests: Update test cases for commit active
commit: Support commit active layer
block: Add commit_active_start()
mirror: Move base to MirrorBlockJob
mirror: Don't close target
qemu-iotests: drop duplicate virtio-blk initialization failure
vmdk: Allow vmdk_create to work with protocol
vmdk: Check VMFS extent line field number
docs: updated qemu-img man page and qemu-doc to reflect VHDX support.
block: vhdx - improve error message, and .bdrv_check implementation
block/iscsi: Fix compilation for libiscsi 1.4.0 (API change)
qapi-schema: fix QEMU 1.8 references
dataplane: replace hostmem with memory_region_find
dataplane: change vring API to use VirtQueueElement
vring: factor common code for error exits
vring: create a common function to parse descriptors
sheepdog: fix dynamic grow for running qcow2 format
Message-id: 1387554416-5837-1-git-send-email-stefanha@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
This includes some Preparatory patches for cpu hotplug for q25 and memory
hotplug by Igor, tests and memory mapping change
by Laszlo and pci reset cleanup by Paolo.
There are also some fixes for fedora and virtio:
included here since they are test blockers for me.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSuF+2AAoJECgfDbjSjVRpTz0IAJhNCC8L2GVt+pm1RAt6lbqZ
u9bCrqfThDORN2mUTEuLu4ZpZC0DYc7d0Jjr5NPesC5G/Afzi5/to6+l7nNZneU3
OdBPglXCCfU/cRaLu7JG2akpha0GVU0tsSCoWIYa6mwlWA4/DXVMgeKg/bh/EgfM
B1w4fE2RgRM9bEqWmX4+tZw8dgk7uVJhu95HCDnb5eikaKlFzwuOlvexrDV3KbPc
bkJe35zbGrKOws93tiSeoqcDx2dcYSzecPoJ0jiCY0KXJ17PBWAvuLTtYqkwwe9J
2FEnTslQJ3Rc8jTFiOPWx2pGaejG4y7Tnk6uuzW6fbbSLOQDPJy3KgmutJFMt1A=
=ShCj
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
acpi,pci,pc,fedora,virtio fixes and enhancements
This includes some Preparatory patches for cpu hotplug for q25 and memory
hotplug by Igor, tests and memory mapping change
by Laszlo and pci reset cleanup by Paolo.
There are also some fixes for fedora and virtio:
included here since they are test blockers for me.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon 23 Dec 2013 08:07:18 AM PST using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
* mst/tags/for_anthony:
target-arm: fix build with gcc 4.8.2
virtio: add back call to virtio_bus_device_unplugged
piix: fix 32bit pci hole
qdev: switch reset to post-order
qdev: allow both pre- and post-order vists in qdev walking functions
pci: clean up resetting of IRQs
pci: do not export pci_bus_reset
ACPI/DSDT-CPU: cleanup bogus comment
ACPI: Q35 DSDT: fix CPU hotplug GPE0.2 handler
acpi: ich9: allow guest to clear SCI rised by GPE
acpi: factor out common pm_update_sci() into acpi core
acpi: piix4: remove not needed GPE0 mask
i440fx-test: verify firmware under 4G and 1M, both -bios and -pflash
i440fx-test: generate temporary firmware blob
i440fx-test: give each GTest case its own qtest
i440fx-test: qtest_start() should be paired with qtest_end()
hw/i386/pc_sysfw: support two flash drives
pc_piix: document gigabyte_align
piix: gigabyte alignment for ram
Message-id: 1387815007-1272-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
* QOM interface fixes and unit test
* Device no_user sanitization and documentation
* Device error reporting improvement
* Conversion of APIC, ICC, IOAPIC to QOM realization model
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=WrhM
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'afaerber/tags/qom-devices-for-anthony' into staging
QOM infrastructure fixes and device conversions
* QOM interface fixes and unit test
* Device no_user sanitization and documentation
* Device error reporting improvement
* Conversion of APIC, ICC, IOAPIC to QOM realization model
# gpg: Signature made Tue 24 Dec 2013 09:04:05 AM PST using RSA key ID 3E7E013F
# gpg: Good signature from "Andreas Färber <afaerber@suse.de>"
# gpg: aka "Andreas Färber <afaerber@suse.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 174F 0347 1BCC 221A 6175 6F96 FA2E D12D 3E7E 013F
* afaerber/tags/qom-devices-for-anthony: (24 commits)
qdev-monitor: Improve error message for -device nonexistant
ioapic: QOM'ify ioapic
ioapic: Cleanup for QOM'ification
icc_bus: QOM'ify ICC
apic: QOM'ify APIC
apic: Cleanup for QOM'ification
qdev: Drop misleading qbus_free() function
qom: Detect bad reentrance during object_class_foreach()
tests: Test QOM interface casting
qom: Do not register interface "types" in the type table and fix names
qom: Split out object and class caches
qdev: Document that pointer properties kill device_add
hw: cannot_instantiate_with_device_add_yet due to pointer props
qdev-monitor: Avoid device_add crashing on non-device driver name
qdev: Do not let the user try to device_add when it cannot work
isa: Clean up use of cannot_instantiate_with_device_add_yet
vt82c686: Clean up use of cannot_instantiate_with_device_add_yet
piix3 piix4: Clean up use of cannot_instantiate_with_device_add_yet
ich9: Document why cannot_instantiate_with_device_add_yet
pci-host: Consistently set cannot_instantiate_with_device_add_yet
...
* mjt/trivial-patches:
acpi unit-test: Remove temporary disk after test
mainstone: Fix duplicate array values for key 'space'
pxa27x: Add 'const' attribute to keyboard maps
pxa27x: Reduce size of keyboard matrix mapping
doc: Mention chardev:id in available devices for -serial
configure: Python tests must be done before help message
configure: Rewrite code for help message
fix -boot strict regressed in commit 6ef4716
vl: make boot_strict variable static (not used outside vl.c)
x86: only allow real mode to access 32bit without LMA
linux-user: Use macro TARGET_NSIG_WORDS where possible
exynos4210: Use macro ARRAY_SIZE where possible
ui/cocoa: Use macro ARRAY_SIZE where possible
misc: Use macro ARRAY_SIZE where possible
openrisc: Fix spelling in comment (transaltion -> translation)
hw/arm/highbank: Simplify code (memory region in device state)
Message-id: 1388182050-10270-1-git-send-email-mjt@msgid.tls.msk.ru
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
To make the code slightly cleaner to look at and make the save/restore
code easier to understand, introduce this function to set the priority of
interrupts.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1387606179-22709-3-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
TRIGGER can really mean mean anything (e.g. was it triggered, is it
level-triggered, is it edge-triggered, etc.). Rename to EDGE_TRIGGER to
make the code comprehensible without looking up the data structure.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1387606179-22709-2-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Don't conditionalise GEM instantiation on networking attachments. The
device should always be present even if not attached to a network.
This allows for probing of the device by expectant guests (such as
OS's). This is needed because sysbus (or AXI in Xilinx's real hw case)
is not self identifying so the guest has no dynamic way of detecting
device absence.
Also allows for testing of the GEM in loopback mode with -net none.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 55649779a68ee3ff54b24c339b6fdbdccd1f0ed7.1388800598.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the UART back-end blocks, buffer in the Tx FIFO to try again later.
This stops the IO-thread busy waiting on char back-ends (which causes
all sorts of performance problems).
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 4bea048b3ab38425701d82ccc1ab92545c26b79c.1388626249.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The can_receive logic was only taking into account the RxFIFO
occupancy. RxFIFO population is only used for the echo and normal modes
however. Improve the logic to correctly return the true number of
receivable characters based on the current mode:
Normal mode: RxFIFO vacancy.
Remote loopback: TxFIFO vacancy.
Echo mode: The min of the TxFIFO and RxFIFO vacancies.
Local Loopback: Return non-zero (to implement droppage)
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 36a58440c9ca5080151e95765c2c81342de8a8df.1388626249.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This tx timer implementation is flawed. Despite the controller
attempting to time the guest visable assertion of the TX-empty status
bit (and corresponding interrupt) the controller is still transmitting
characters instantaneously. There is also no sense of multiple character
delay.
The only side effect of this timer is assertion of tx-empty status. So
just remove the timer completely and hold tx-empty as permanently
asserted (its reset status). This matches the actual behaviour of
instantaneous transmission.
While we are VMSD version bumping, add the tx_fifo as device state to
prepare for upcomming TxFIFO flow control. Implement the interrupt
generation logic for the TxFIFO occupancy.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 7a208a7eb8d79d6429fe28b1396c3104371807b2.1388626249.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some (interrupt) status register bits relating to the TxFIFO path were
not defined. Define them. This prepares support for proper Tx data path
flow control.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 2068b963f0af8cc834c353944e9fa816d950b163.1388626249.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The status register bits are always pure functions of other device
state. Move the generation of these bits to the update_status()
function to simplify. Makes developing much easier as theres now no need
to recheck status bits on all the changes to rx/tx fifo state.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 321994929f789096975104f99c55732774be4cae.1388626249.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This should be rechecked on bus write accesses as such accesses may
change the underlying state that generates the interrupt. Particular
relevant for when the guest touches the interrupt status or mask.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 1c250cd61b7b8de492fbc8b79b8370958a56d83b.1388626249.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a boiler-plate _nofail variant of qemu_opts_create. Remove and
use error_abort in call sites.
null/0 arguments needs to be added for the id and fail_if_exists fields
in affected callsites due to argument inconsistency between the normal and
no_fail variants.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Replace assert_no_error() usages with the error_abort system.
&error_abort is passed into API calls to signal to the Error sub-system
that any errors are fatal. Removes need for caller assertions.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
This is unreachable code, as it's already asserted that no errors have
occurred. Delete.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
cgcc reported a duplicate initialisation. Mainstone includes a matrix
keyboard where two different positions map to 'space'.
QEMU uses the reversed mapping and does not map 'space' to two different
matrix positions.
Some other keys are either missing or might be mapped wrongly (cf. Linux
kernel code). Don't fix these until someone can test them with real
hardware, but add TODO comments.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The mapping is a hardware feature, so it is relatively constant.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Convert 'init' function to QOM's 'realize' for ioapic and kvm-ioapic.
Change variable 'ioapic_no' from static to global. Then we can drop
the 'instance_no' function argument.
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Some cleanups:
* ioapic_common.c: Rename 'register_types' to 'ioapic_common_register_types'
* Replace inline 'DEVICE(s)' with local 'DeviceState *dev' variable
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Convert 'init' function to QOM's 'realize' for apic, kvm/apic and
xen/xen_apic.
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Do some cleanup, including:
1. Remove DO_UPCAST() for APICCommonState
2. Change DeviceState pointers from 'd' to 'dev', better to understand
3. Rename 'register_types' to specifically 'apic_common_register_types'
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Same reasoning as commit 02a5c4c974
("qdev: Drop misleading qdev_free() function"). The qbus_free()
function removes the child from the namespace and decrements the
reference count. It does not, however, guarantee to free the child
since the refcount may still be held.
Just call object_unparent() directly.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Pointer properties can be set only by code, not by device_add. A
device with a pointer property can work with device_add only when the
property may remain null.
This is the case for property "interrupt_vector" of device
"etraxfs,pic". Add a comment there.
Set cannot_instantiate_with_device_add_yet for the other devices with
pointer properties, with a comment explaining why.
Juha Riihimäki and Peter Maydell deserve my thanks for making "pointer
property must not remain null" blatantly obvious in the OMAP devices.
Only device "smbus-eeprom" is actually changed. The others are all
sysbus devices, which get cannot_instantiate_with_device_add_yet set
in their abstract base's class init function. Setting it again in
their class init function is technically redundant, but serves as
insurance for when sysbus devices become available with device_add,
and as documentation.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com> (for ETRAX)
Signed-off-by: Andreas Färber <afaerber@suse.de>
This got lost in a rebase.
Reported-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make the 32bit pci hole start at end of ram, so all possible address
space is covered.
We used to try and make addresses aligned so they are easier to cover
with MTRRs, but since they are cosmetic on KVM, this is probably not
worth worrying about.
Of course the firmware can use less than that. Leaving space unused is
no problem, mapping pci bars outside the hole causes problems though.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This motion is preparing for refactoring vCPU APIC subsequently.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
This improves readability and simplifies the code.
Cc: Dmitry Solodkiy <d.solodkiy@samsung.com>
Cc: Evgeny Voevodin <e.voevodin@samsung.com>
Cc: Igor Mitsyanko <i.mitsyanko@gmail.com>
Cc: Maksim Kozlov <m.kozlov@samsung.com>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This improves readability and simplifies the code.
Cc: Anthony Liguori <aliguori@amazon.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The memory region can be included by value instead of by reference in the
device state.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Post-order is the only sensible direction for the reset signals.
For example, suppose pre-order is used and the parent has some data
structures that cache children state (for example a list of active
requests). When the reset method is invoked on the parent, these caches
could be in any state.
If post-order is used, on the other hand, these will be in a known state
when the reset method is invoked on the parent.
This change means that it is no longer possible to block the visit of
the devices, so the callback is changed to return void. This is not
a problem, because PCI was returning 1 exactly in order to achieve the
same ordering that this patch implements.
PCI can then rely on the qdev core having sent a "reset signal" (whatever
that means) to the device, and only do the PCI-specific initialization
with pci_do_device_reset.
MST: fixed up virtio-ccw
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Resetting should be done in post-order, not pre-order. However,
qdev_walk_children and qbus_walk_children do not allow this. Fix
it by adding two extra arguments to the functions.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_device_reset will deassert the INTX pins, and this will make the
irq_count array all-zeroes. Check that this is the case, and remove
the existing loop which might even unsync irq_count and irq_state.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
qbus_reset_all can be used instead. There is no semantic change
because pcibus_reset returns 1 and takes care of the device
tree traversal.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fix bogus CPU hotplug GPE handler.
Make Q35 CPU hotplug GPE handler match PIIX4 one, since
CPU hotplug event is triggered by GPE0.2 register.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it fixes IRQ storm since guest isn't able to lower SCI IRQ
after it has been handled when it clears GPE event.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
... and rename it into acpi_update_sci() since it changes
SCI on only on PM registers status.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Paolo Bonzini