In case of VLAN stripping ETH header is stored in a
separate chunk and length of IOV should take this into
account.
This patch fixes checksum validation for RX packets
with VLAN header.
Devices affected by this problem: e1000e and vmxnet3.
Cc: qemu-stable@nongnu.org
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
In case of VLAN stripping, ETH header put into a
separate buffer, therefore amont of data copied
from original IOV should be smaller.
Cc: qemu-stable@nongnu.org
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch fixed a problem that was introduced in commit eb700029.
When net_rx_pkt_attach_iovec() calls eth_strip_vlan()
this can result in pkt->ehdr_buf being overflowed, because
ehdr_buf is only sizeof(struct eth_header) bytes large
but eth_strip_vlan() can write
sizeof(struct eth_header) + sizeof(struct vlan_header)
bytes into it.
Devices affected by this problem: vmxnet3.
Cc: qemu-stable@nongnu.org
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This has been pointless since commit 605d52e62, which was a
search-and-replace, overlooked the redundancy.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The spapr-vlan device in QEMU has always presented it's MAC address in
the device tree as an 8 byte value, even though PAPR requires it to be
6 bytes. This is because, at the time, AIX required the value to be 8
bytes. However, modern versions of AIX support the (correct) 6
byte value so they no longer require the workaround.
It would be neatest to always provide a 6 byte value but that would
cause a problem with old Linux kernel ibmveth drivers, so the old 8
byte value is still presented when necessary.
Since commit 13f85203e (3.10, May 2013) the driver has been able to
handle 6 or 8 byte addresses so versions after that don't need to be
considered specially.
Drivers from kernels before that can also handle either type of
address, but not always:
* If the first byte's lowest bits are 10, the address must be 6 bytes.
* Otherwise, the address must be 8 bytes.
(The two bits in question are significant in a MAC address: they
indicate a locally-administered unicast address.)
So to maintain compatibility the old 8 byte value is presented when
the lowest two bits of the first byte are not 10.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The virtio-net change is necessary because it uses virtqueue_fill
and virtqueue_flush instead of the more convenient virtqueue_push.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This issue is like the issue in e1000 network card addressed in
this commit:
e1000: eliminate infinite loops on out-of-bounds transfer start.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
i.MX Fast Ethernet Controller uses buffer descriptors to manage
data flow to/fro receive & transmit queues. While transmitting
packets, it could continue to read buffer descriptors if a buffer
descriptor has length of zero and has crafted values in bd.flags.
Set an upper limit to number of buffer descriptors.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Because is_first is declared inside a loop, it is always true. The store
is dead, and so is the "else" branch of "if (is_first)". is_last is
okay though.
Reported by Coverity.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20170203160651.19917-5-dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Merge fix against Halil's removal of the '_start' field in
VMSTATE_VBUFFER_MULTIPLY
The member VMStateField.start is used for two things, partial data
migration for VBUFFER data (basically provide migration for a
sub-buffer) and for locating next in QTAILQ.
The implementation of the VBUFFER feature is broken when VMSTATE_ALLOC
is used. This however goes unnoticed because actually partial migration
for VBUFFER is not used at all.
Let's consolidate the usage of VMStateField.start by removing support
for partial migration for VBUFFER.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20170203175217.45562-1-pasic@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
msix_init() reports errors with error_report(), which is wrong when
it's used in realize(). The same issue was fixed for msi_init() in
commit 1108b2f. In order to make the API change as small as possible,
leave the return value check to later patch.
For some devices(like e1000e, vmxnet3, nvme) who won't fail because of
msix_init's failure, suppress the error report by passing NULL error
object.
Bonus: add comment for msix_init.
CC: Jiri Pirko <jiri@resnulli.us>
CC: Gerd Hoffmann <kraxel@redhat.com>
CC: Dmitry Fleytman <dmitry@daynix.com>
CC: Jason Wang <jasowang@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Hannes Reinecke <hare@suse.de>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Alex Williamson <alex.williamson@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There are a number of unused trace events that
scripts/cleanup-trace-events.pl finds. The "hw/vfio/pci-quirks.c"
filename was typoed and "qapi/qapi-visit-core.c" was missing the qapi/
directory prefix.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170126171613.1399-3-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Introduce rules in the top level Makefile that are able to generate
trace.[ch] files in every subdirectory which has a trace-events file.
The top level directory is handled specially, so instead of creating
trace.h, it creates trace-root.h. This allows sub-directories to
include the top level trace-root.h file, without ambiguity wrt to
the trace.g file in the current sub-dir.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170125161417.31949-7-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When the guest attempts to start an MII register
access via the MCTL register, clear the START bit,
so that when the guest reads it back the register
transaction will be signalled as having completed.
This avoids the guest spinning as it polls the
START bit waiting for it to clear (which it
previously never would).
The MII registers themselves still aren't implemented,
but at least we can avoid guests spending quite so much
time busy waiting.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1484938222-1423-1-git-send-email-peter.maydell@linaro.org
[PMM: expand commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The vmstate_pci_device and vmstate_pcie_devices differ
just in the size of one buffer; combine the two using a _TEST
macro.
I think this is safe as long as everywhere which currently
uses either of these two uses the right type.
One thing that concerns me is that some places use pci_device_load/save
which does some irq mangling, but others just use the VMSTATE_PCI_DEVICE
macro - how are they getting the same irq mangling?
This passes a smoke test migrate of:
./x86_64-softmmu/qemu-system-x86_64 -M pc,accel=kvm -m 1024
./littlefed20.img -device e1000e -device virtio-net -device
e1000 -device virtio-rng -device megasas -device megasas-gen2 -device
ioh3420 -device nec-usb-xhci
to an unmodified qemu.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20161214195829.18241-1-dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Current migration code cannot handle some data structures such as
QTAILQ in qemu/queue.h. Here we extend the signatures of put/get
in VMStateInfo so that customized handling is supported. put now
will return int type.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jianjun Duan <duanj@linux.vnet.ibm.com>
Message-Id: <1484852453-12728-2-git-send-email-duanj@linux.vnet.ibm.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJYgXzxAAoJEO8Ells5jWIRgtAIAKuFrOBE/xJnjd/45sVKcx2j
fsohKHF8T/eLmt5sw+MhGtnM/oRJRUX8kGpA9AU8m6TCSaTYh2tOKX5lwrykuAzk
feqz2pqZFwiLWs5Ro7qEQIhMkqtFetODvKd05qnKnAldj8SC45czKxdghmSP/B+w
4nnDEdqVqUuUseDCa1mW1b4f6g1N93LbgChK7lK9Xqg+OqeEbQ7nLgVvcWvN7+Ea
DfDKWP8tjQ5QhjzFWc4wa9/Tx+0HI7Dn57fv98XdJMvm1kt/MdnO7QKAXWmHH5s/
6DX+NHgN0ZAn85gv/ufq1F9C4TstbAoZA9EOGhoBJ5ww8mueARB3L2iCj+OcS9A=
=gkbh
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Fri 20 Jan 2017 02:58:57 GMT
# gpg: using RSA key 0xEF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
tap: fix memory leak on failure in net_init_tap()
hw/pci: use-after-free in pci_nic_init_nofail when nic device fails to initialize
hw/net/dp8393x: Avoid unintentional sign extensions on addresses
m68k: QOMify the MCF Fast Ethernet Controller device
net: optimize checksum computation
docs: Fix description of the sentence
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The dp8393x has several 32-bit values which are formed by concatenating
two 16 bit device register values. Attempting to do these inline
with ((s->reg[HI] << 16) | s->reg[LO]) can result in an unintended
sign extension because "x << 16" is of type 'int' even though s->reg
is unsigned, and so if the expression is used in a context where
it is cast to uint64_t the value is incorrectly sign-extended.
Fix this by using accessor functions with a uint32_t return type;
this also makes the code a bit easier to read.
This should fix Coverity issues 1307765, 1307766, 1307767, 1307768.
(To avoid having a ctda read function only used in a DPRINTF,
we move the DPRINTF down slightly so it can use the ttda function.)
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When running qemu-system-m68k with the "-net" parameter (for example
simply "-net nic -net user"), there is currently a confusing warning
message saying:
Warning: requested NIC (anonymous, model mcf_fec) was not created
(not supported by this machine?)
This seems to happen because the MCF NIC has never been adapted to
the currently expected QEMU device behavior. Thus let's QOMify the
NIC now to get rid of the warning message.
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patches implements Device IOTLB support for vhost kernel. This is
done through:
1) switch to use dma helpers when map/unmap vrings from vhost codes
2) introduce a set of VhostOps to:
- setting up device IOTLB request callback
- processing device IOTLB request
- processing device IOTLB invalidation
2) kernel support for Device IOTLB API:
- allow vhost-net to query the IOMMU IOTLB entry through eventfd
- enable the ability for qemu to update a specified mapping of vhost
- through ioctl.
- enable the ability to invalidate a specified range of iova for the
device IOTLB of vhost through ioctl. In x86/intel_iommu case this is
triggered through iommu memory region notifier from device IOTLB
invalidation descriptor processing routine.
With all the above, kernel vhost_net can co-operate with userspace
IOMMU. For vhost-user, the support could be easily done on top by
implementing the VhostOps.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch allows advising guest with host MTU's by setting
host_mtu parameter.
If VIRTIO_NET_F_MTU has been successfully negotiated, MTU
value is passed to the backend.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Aaron Conole <aconole@redhat.com
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch provides a way for virtio-net to notify the
backend about the host MTU set by the user.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Aaron Conole <aconole@redhat.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1295637
Upon set_link monitor command or upon netdev deletion
virtio-net sends link down indication to the guest
and stops vhost if one is used.
Guest driver can still submit data for TX until it
recognizes link loss. If these packets not returned by
the host, the Windows guest will never be able to finish
disable/removal/shutdown.
Now each packet sent by guest after NIC indicated link
down will be completed immediately.
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now, AER capa version is fixed to v2, if assigned device isn't v2,
then this value will be inconsistent between guest and host
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When user specify invalid value for property aer_log_max, device should
fail to create, and report appropriate message.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Dmitry Fleytman <dmitry@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Current code that handles Tx buffer desciprtor ring scanning employs the
following algorithm:
1. Restore current buffer descriptor pointer from TBPTRn
2. Process current descriptor
3. If current descriptor has BD_WRAP flag set set current
descriptor pointer to start of the descriptor ring
4. If current descriptor points to start of the ring exit the
loop, otherwise increment current descriptor pointer and go
to #2
5. Store current descriptor in TBPTRn
The way the code is implemented results in buffer descriptor ring being
scanned starting at offset/descriptor #0. While covering 99% of the
cases, this algorithm becomes problematic for a number of edge cases.
Consider the following scenario: guest OS driver initializes descriptor
ring to N individual descriptors and starts sending data out. Depending
on the volume of traffic and probably guest OS driver implementation it
is possible that an edge case where a packet, spread across 2
descriptors is placed in descriptors N - 1 and 0 in that order(it is
easy to imagine similar examples involving more than 2 descriptors).
What happens then is aforementioned algorithm starts at descriptor 0,
sees a descriptor marked as BD_LAST, which it happily sends out as a
separate packet(very much malformed at this point) then the iteration
continues and the first part of the original packet is tacked to the
next transmission which ends up being bogus as well.
This behvaiour can be pretty reliably observed when scp'ing data from a
guest OS via TAP interface for files larger than 160K (every time for
700K+).
This patch changes the scanning algorithm to do the following:
1. Restore "current" buffer descriptor pointer from
TBPTRn
2. If "current" descriptor does not have BD_TX_READY set, goto #6
3. Process current descriptor
4. If "current" descriptor has BD_WRAP flag set "current"
descriptor pointer to start of the descriptor ring otherwise
set increment "current" by the size of one descriptor
5. Goto #1
6. Save "current" buffer descriptor in TBPTRn
This way we preserve the information about which descriptor was
processed last and always start where we left off avoiding the original
problem. On top of that, judging by the following excerpt from
MPC8548ERM (p. 14-48):
"... When the end of the TxBD ring is reached, eTSEC initializes TBPTRn
to the value in the corresponding TBASEn. The TBPTR register is
internally written by the eTSEC’s DMA controller during
transmission. The pointer increments by eight (bytes) each time a
descriptor is closed successfully by the eTSEC..."
revised algorithm might also a more correct way of emulating this aspect
of eTSEC peripheral.
Cc: Alexander Graf <agraf@suse.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: qemu-devel@nongnu.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
According to datasheet:
"[Bit 15 of Basic Mode Control Register] sets the status and control registers
of the PHY (register 0062-0074) in a default state. This bit is self-clearing.
1 = software reset; 0 = normal operation."
This fixes the netcard detection failure in Minoca OS.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Fix various small problems in hexdump code, such as:
- Reference to non-existing field etsec->nic->nc.name is replaced
with nc->name
- Type mismatch warnings
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Depending on QEMU network setup it is possible for us to receive a
complete Ethernet packet that is less 64 bytes long. One such example is
when QEMU is configured to use a standalone TAP device (not set to be a
part of any bridge) receives and ARP packet. In cases like that we need
to add more than just 4-bytes of CRC padding and ensure that our payload
is at least 60 bytes long, such that, when combined with CRC padding
bytes the resulting size is at least 802.3 minimum MTU bytes
long (64). Failing to do that results in code in etsec_walk_rx_ring()
setting BD_RX_SH which, in turn, makes corresponding Linux driver of
emulated host to reject buffer as a runt packet
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
ColdFire Fast Ethernet Controller uses a receive buffer size
register(EMRBR) to hold maximum size of all receive buffers.
It is set by a user before any operation. If it was set to be
zero, ColdFire emulator would go into an infinite loop while
receiving data in mcf_fec_receive. Add check to avoid it.
Reported-by: Wjjzhang <wjjzhang@tencent.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Lots of fixes all over the place.
Unfortunately, this does not yet fix a regression with vhost
introduced by the last pull, the issue is typically this error:
kvm_mem_ioeventfd_add: error adding ioeventfd: File exists
followed by QEMU aborting.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYKyfxAAoJECgfDbjSjVRpI4oH/2ZBpUxT/neq4ezX0bou5+1R
lQ1m0VI1JDbay5uYw0Z0rUY7aLP0kX2XLu2jNBZg7fGz3+BPhqAoEjkGdlUran79
fEnuYCvMMokQNzvMaHv+lFXO/MuEJthdDeUJyi4B0NU0sseutiz8opXuSWIC8Ncx
pyqRb8AfgKnsUSRizEVfiOWI1fk+zsTFbSyUwajwKi5E7RNEuHwLiqk5VFhzrrTX
nLwnUvlH7NrcDfliam9ziadhguo5cwCE4jBlMpeHnW5tGalNRulvF5EgwXybIdrU
JaR6lzQabOcoaAuJJ/dgo336B1Ef3JA/hogqfTW4unJGL5VVkWT0HLZ9OV42NEg=
=ibZy
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, vhost, pc, pci: documentation, fixes and cleanups
Lots of fixes all over the place.
Unfortunately, this does not yet fix a regression with vhost
introduced by the last pull, the issue is typically this error:
kvm_mem_ioeventfd_add: error adding ioeventfd: File exists
followed by QEMU aborting.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* remotes/mst/tags/for_upstream: (28 commits)
docs: add PCIe devices placement guidelines
virtio: drop virtio_queue_get_ring_{size,addr}()
vhost: drop legacy vring layout bits
vhost: adapt vhost_verify_ring_mappings() to virtio 1 ring layout
nvdimm acpi: introduce NVDIMM_DSM_MEMORY_SIZE
nvdimm acpi: use aml_name_decl to define named object
nvdimm acpi: rename nvdimm_dsm_reserved_root
nvdimm acpi: fix two comments
nvdimm acpi: define DSM return codes
nvdimm acpi: rename nvdimm_acpi_hotplug
nvdimm acpi: cleanup nvdimm_build_fit
nvdimm acpi: rename nvdimm_plugged_device_list
docs: improve the doc of Read FIT method
nvdimm acpi: clean up nvdimm_build_acpi
pc: memhp: stop handling nvdimm hotplug in pc_dimm_unplug
pc: memhp: move nvdimm hotplug out of memory hotplug
nvdimm acpi: drop the lock of fit buffer
qdev: hotplug: drop HotplugHandler.post_plug callback
vhost: migration blocker only if shared log is used
virtio-net: mark VIRTIO_NET_F_GSO as legacy
...
Message-id: 1479237527-11846-1-git-send-email-mst@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
virtio 1.0 spec says this is a legacy feature bit,
hide it from guests in modern mode.
Note: for cross-version migration compatibility,
we keep the bit set in host_features.
The result will be that a guest migrating cross-version
will see host features change under it.
As guests only seem to read it once, this should
not be an issue. Meanwhile, will work to fix guests to
ignore this bit in virtio1 mode, too.
Cc: qemu-stable@nongnu.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The function undoes the effect of virtqueue_pop and doesn't do anything
destructive or irreversible so virtqueue_unpop is a more fitting name.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1373816
qemu core dump happens during repetitive unpug-plug
with multiple queues and Windows RSS-capable guest.
If back-end delete requested during virtio-net device
initialization, driver still can try configure the device
for multiple queues. The virtio-net device is expected
to be removed as soon as the initialization is done.
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Prepare xen_be_send_notify to be shared with frontends:
* xen_be_send_notify -> xen_pv_send_notify
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Prepare xen_be_unbind_evtchn to be shared with frontends:
* xen_be_unbind_evtchn -> xen_pv_unbind_evtchn
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Prepare xen_be_printf to be used by both backend and frontends:
* xen_be_printf -> xen_pv_printf
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Fixes:
* WARNING: line over 80 characters
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Fixes the following errors:
* ERROR: line over 90 characters
* ERROR: code indent should never use tabs
* ERROR: space prohibited after that open square bracket '['
* ERROR: do not initialise statics to 0 or NULL
* ERROR: "(foo*)" should be "(foo *)"
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
RTL8139 ethernet controller in C+ mode supports multiple
descriptor rings, each with maximum of 64 descriptors. While
processing transmit descriptor ring in 'rtl8139_cplus_transmit',
it does not limit the descriptor count and runs forever. Add
check to avoid it.
Reported-by: Andrew Henderson <hendersa@icculus.org>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
In Vmxnet3 device emulator while processing transmit(tx) queue,
when it reaches end of packet, it calls vmxnet3_complete_packet.
In that local 'txcq_descr' object is not initialised, which could
leak host memory bytes a guest.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The e1000e emulation zeroes out any used rx descriptor and then writes a
completely newly constructed value there. By doing this, it doesn't only
update the write-back area of the descriptors (as it's supposed to do),
but it also clears the buffer address, which real hardware doesn't do.
The spec explicitly mentions in chapter 7.1.8 that it is valid for a
driver to reuse a descriptor and only update the status field while
doing so, i.e. reusing the old buffer address:
If software statically allocates buffers, and uses memory read to
check for completed descriptors, it simply has to zero the status
byte in the descriptor to make it ready for reuse by hardware.
This patch fixes the behaviour to leave the buffer address in
descriptors unchanged even after the descriptor has been used.
Signed-off-by: Kevin Wolf <mail@kevin-wolf.de>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Rocker network switch emulator has test registers to help debug
DMA operations. While testing host DMA access, a buffer address
is written to register 'TEST_DMA_ADDR' and its size is written to
register 'TEST_DMA_SIZE'. When performing TEST_DMA_CTRL_INVERT
test, if DMA buffer size was greater than 'INT_MAX', it leads to
an invalid buffer access. Limit the DMA buffer size to avoid it.
Reported-by: Huawei PSIRT <psirt@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The exit dispatch of eepro100 network card device doesn't free
the 's->vmstate' field which was allocated in device realize thus
leading a host memory leak. This patch avoid this.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Fix indentations and source format at few places. Add braces
around 'if' and 'while' statements.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The AMD PC-Net II emulator has set of control and status(CSR)
registers. Of these, CSR76 and CSR78 hold receive and transmit
descriptor ring length respectively. This ring length could range
from 1 to 65535. Setting ring length to zero leads to an infinite
loop in pcnet_rdra_addr() or pcnet_transmit(). Add check to avoid it.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Now all the usages of the old version of VMSTATE_VIRTIO_DEVICE are gone,
so we can get rid of the conditionals, and the old macro.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use the new VMSTATE_VIRTIO_DEVICE macro.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
All these errors are caused by a buggy guest: let's switch the device to
the broken state instead of terminating QEMU. Also we detach the element
from the virtqueue and free it.
If this happens, virtio_net_flush_tx() also returns -EINVAL, so that all
callers can stop processing the virtqueue immediatly.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
All these errors are caused by a buggy guest: let's switch the device to
the broken state instead of terminating QEMU. Also we detach the element
from the virtqueue and free it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This error is caused by a buggy guest: let's switch the device to the
broken state instead of terminating QEMU. Also we detach the element
from the virtqueue and free it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There was an error with some of the register implementation assuming
there are 16 priority queues supported when the IP only supports 8. This
patch corrects the registers to only support 8 queues.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 33bf2d28326d22875602234b8b15cf56fb678333.1474911607.git.alistair.francis@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This uses the wrong frame size for packets composed of multiple
descriptors.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This uses the wrong frame size for packets composed of multiple
descriptors.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
ColdFire Fast Ethernet Controller uses buffer descriptors to manage
data flow to/fro receive & transmit queues. While transmitting
packets, it could continue to read buffer descriptors if a buffer
descriptor has length of zero and has crafted values in bd.flags.
Set upper limit to number of buffer descriptors.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch fixes 2 issues:
1. Bits set in EIAC register should be cleared
from IMS when EIAM is not used.
2. Only bit that corresonds to the interrupt being
raised should be cleared.
See spec. 10.2.4.7 Interrupt Auto Clear
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Do not raise ACK interrupts when
RFCTL.ACKDIS bit is set (see spec. 10.2.5.16).
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Interrupt mask for legacy OTHER causes should
not apply to MSI-X OTHER cause.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch fixes incorrect check for
interrypt type being used.
PBSCLR register is valid for MSI-X only.
See spec. 10.2.3.13 MSI—X PBA Clear
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
CTRL_EXT.EIAME bit controls clearing of IAM bits,
but current code clears IMS bits instead.
See spec. 10.2.2.5 Extended Device Control Register.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Before this patch first netdev queue only was flushed.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
hw/net/e1000e_core.c:56: warning: e1000e_set_interrupt_cause declared inline after being called
hw/net/e1000e_core.c:56: warning: previous declaration of e1000e_set_interrupt_cause was here
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This allows increasing the rx queue size up to 1024: unlike with tx,
guests don't put in huge S/G lists into RX so the risk of running into
the max 1024 limitation due to some off-by-one seems small.
It's helpful for users like OVS-DPDK which don't do any buffering on the
host - 1K roughly matches 500 entries in tun + 256 in the current rx
queue, which seems to work reasonably well. We could probably make do
with ~750 entries but virtio spec limits us to powers of two.
It might be a good idea to specify an s/g size limit in a future
version.
It also might be possible to make the queue size smaller down the road, 64
seems like the minimal value which will still work (as guests seem to
assume a queue full of 1.5K buffers is enough to process the largest
incoming packet, which is ~64K). No one actually asked for this, and
with virtio 1 guests can reduce ring size without need for host
configuration, so don't bother with this for now.
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Jason Wang <jasowang@redhat.com>
Suggested-by: Patrik Hermansson <phermansson@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This pull request supersedes ppc-for-2.8-20160922. There was a clang
build error in that, and I've also added one extra patch in the new pull.
Included in this set of ppc and spapr patches are:
* TCG implementations for more POWER9 instructions
* Some preliminary XICS fixes in preparataion for the pnv machine type
* A significant ADB (Macintosh kbd/mouse) cleanup
* Some conversions to use trace instead of debug macros
* Fixes to correctly handle global TLB flush synchronization in
TCG. This is already a bug, but it will have much more impact
when we get MTTCG
* Add more qtest testcases for Power
* Some MAINTAINERS updates
* Assorted bugfixes
* Add the basics of NUMA associativity to the spapr PCI host bridge
This touches some test files and monitor.c which are technically
outside the ppc code, but coming through this tree because the changes
are primarily of interest to ppc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=et1C
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.8-20160923' into staging
ppc patch queue 2016-09-23
This pull request supersedes ppc-for-2.8-20160922. There was a clang
build error in that, and I've also added one extra patch in the new pull.
Included in this set of ppc and spapr patches are:
* TCG implementations for more POWER9 instructions
* Some preliminary XICS fixes in preparataion for the pnv machine type
* A significant ADB (Macintosh kbd/mouse) cleanup
* Some conversions to use trace instead of debug macros
* Fixes to correctly handle global TLB flush synchronization in
TCG. This is already a bug, but it will have much more impact
when we get MTTCG
* Add more qtest testcases for Power
* Some MAINTAINERS updates
* Assorted bugfixes
* Add the basics of NUMA associativity to the spapr PCI host bridge
This touches some test files and monitor.c which are technically
outside the ppc code, but coming through this tree because the changes
are primarily of interest to ppc.
# gpg: Signature made Fri 23 Sep 2016 08:14:47 BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.8-20160923: (45 commits)
spapr_pci: Add numa node id
monitor: fix crash for platforms without a CPU 0
linux-user: ppc64: fix ARCH_206 bit in AT_HWCAP
ppc/kvm: Mark 64kB page size support as disabled if not available
ppc/xics: An ICS with offset 0 is assumed to be uninitialized
ppc/xics: account correct irq status
Enable H_CLEAR_MOD and H_CLEAR_REF hypercalls on KVM/PPC64.
target-ppc: tlbie/tlbivax should have global effect
target-ppc: add flag in check_tlb_flush()
target-ppc: add TLB_NEED_LOCAL_FLUSH flag
spapr: Introduce sPAPRCPUCoreClass
target-ppc: implement darn instruction
target-ppc: add stxsi[bh]x instruction
target-ppc: add lxsi[bw]zx instruction
target-ppc: add xxspltib instruction
target-ppc: consolidate store conditional
target-ppc: move out stqcx impementation
target-ppc: consolidate load with reservation
target-ppc: convert st[16,32,64]r to use new macro
target-ppc: convert st64 to use new macro
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix up the indentation inside the for loop that was introduced in the previous
patch. This commit is almost empty if viewed using 'git show -w', except for a
few changes that were required to avoid the 80 charecter line limit.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: b40d1b12d24be9f0ac5d72f86249103e0c1c720a.1469727764.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Cadence GEM hardware allows incoming data to be 'screened' based on some
register values. Add support for these screens.
We also need to increase the max regs to avoid compilation failures. These new
registers are implemented in the next patch.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 73e69a8ad9fa2763e9f68f71eaf2469dd5744fcc.1469727764.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Cadence GEM hardware supports N number priority queues, this patch is a
step towards that by adding the property to set the queues. At the moment
behaviour doesn't change as we only use queue 0.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 6543ec0d0c4bfd2678d0ed683efb197e91b17733.1469727764.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The sysbus_init_irq() call will eventually depend on a property so it needs to
be in the realize function.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 486595809cf416d18a750aafbcfa1c81d7160c59.1469727764.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some of the timer devices may behave differently from what ptimer
provides. Introduce ptimer policy feature that allows ptimer users to
change default and wrong timer behaviour, for example to continuously
trigger periodic timer when load value is equal to "0".
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: 994cd608ec392da6e58f0643800dda595edb9d97.1473252818.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
slave:~/.xie/qemu-colo # gcc --version
gcc (SUSE Linux) 4.3.4 [gcc-4_3-branch revision 152973]
slave:~/.xie/qemu-colo # make -j8
CC hw/net/e1000e_core.o
hw/net/e1000e_core.c:56: warning: ‘e1000e_set_interrupt_cause’ declared inline after being called
hw/net/e1000e_core.c:56: warning: previous declaration of ‘e1000e_set_interrupt_cause’ was here
LINK x86_64-softmmu/qemu-system-x86_64
Signed-off-by: Changlong Xie <xiecl.fnst@cn.fujitsu.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Since kernel v4.0, linux uses H_CHANGE_LOGICAL_LAN_MAC to change lively
the MAC address of an ibmveth interface.
As QEMU doesn't implement this h_call, we can't change anymore the
MAC address of an spapr-vlan interface.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 66bf7d58 removed internal msi state flag E1000E_USE_MSI, E1000E_USE_MSIX
is not necessary too, remove it now. And interrupt flag field intr_state also
can be removed now.
CC: Dmitry Fleytman <dmitry@daynix.com>
CC: Jason Wang <jasowang@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Marcel Apfelbaum <marcel@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Dmitry Fleytman <dmitry@daynix.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When network transport abstraction layer initialises pkt, the maximum
fragmentation count is not checked. This could lead to an integer
overflow causing a NULL pointer dereference. Replace g_malloc() with
g_new() to catch the multiplication overflow.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Acked-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
'vhost_set_vring_enable()' tries to call function using pointer to
'vhost_ops' which can be already zeroized in 'vhost_dev_cleanup()'
while vhost disconnection.
Fix that by checking 'vhost_ops' before using. This fixes QEMU crash
on calling 'ethtool -L eth0 combined 2' if vhost disconnected.
Signed-off-by: Ilya Maximets <i.maximets@samsung.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The .receive callback of xlnx.xps-ethernetlite doesn't check the length
of data before calling memcpy. As a result, the NetClientState object in
heap will be overflowed. All versions of qemu with xlnx.xps-ethernetlite
will be affected.
Reported-by: chaojianhu <chaojianhu@hotmail.com>
Signed-off-by: chaojianhu <chaojianhu@hotmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Vmxnet3 device emulator does not check if the device is active,
before using it for write. It leads to a use after free issue,
if the vmxnet3_io_bar0_write routine is called after the device is
deactivated. Add check to avoid it.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Acked-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Network transport abstraction layer supports packet fragmentation.
While fragmenting a packet, it checks for more fragments from
packet length and current fragment length. It is susceptible
to an infinite loop, if the current fragment length is zero.
Add check to avoid it.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
CC: qemu-stable@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Not all vhost-user backends support ops->vhost_net_set_backend(). It is
a nicer to provide an assert/error than to crash trying to
call. Furthermore, it improves a bit the code by hiding vhost_ops
details.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Either the callback is mandatory to implement, in which case an assert()
is more appropriate, or it's not and we can't tell much whether the
function should fail or not (given it's name, I guess it should silently
success by default). Instead, make the implementation mandatory and
vhost-user specific to be more clear about its usage.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now that get_vhost_net() returns non-null after a successful
vhost_net_init(), we no longer need to check this case.
This reverts commit ecd34898596c60f79886061618dd7e01001113ad.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a few assertions to be more explicit about the runtime behaviour
after the previous patch: get_vhost_net() is non-null after
net_vhost_user_init().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Many code paths assume get_vhost_net() returns non-null.
Keep VhostUserState.vhost_net after a successful vhost_net_init(),
instead of freeing it in vhost_net_cleanup().
VhostUserState.vhost_net is thus freed before after being recreated or
on final vhost_user_cleanup() and there is no need to save the acked
features.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost_dev_init(), calling vhost backend initialization, should be
cleaned up after failure too. Call vhost_dev_cleanup() in all failure
cases. First, it needs to zero-alloc the struct to avoid the initial
garbage.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
- interrupt remapping for intel iommus
- a bunch of virtio cleanups
- fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXkQsqAAoJECgfDbjSjVRpanoIAJ9JVlc1aEjt9sa0cSBcs+NQ
J7JmgU9FqFsj+4FrNTouO3AxTjHurd1UAULP1WMPD+V3JpbnHct8r6SCBLQ5EBMN
VOjYo4DwWs1g+DqnQ9WZmbadu06XvYi/yiAKNUzWfZk0MR11D0D/S5hmarNKw0Kq
tGHeTWjGeY4WqFLV7m+qB4+cqkAByn6um99UtUvgLL05RgIEIP2IEMKYZ+rXvAa9
iGUvzqlO7mbq/+LbL18kaWywa4TCwbbd2eSGWaqhX4CuB62Rl33mWTXFcfaYhkyp
Z3FgwaJ09h0lAjSVEbyAuLFMfO/BnMcsoKqwl4xc4vkn/xBCqFtgH9JcEVm3O8U=
=ge2D
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio: new features, cleanups, fixes
- interrupt remapping for intel iommus
- a bunch of virtio cleanups
- fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 21 Jul 2016 18:49:30 BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (57 commits)
intel_iommu: avoid unnamed fields
virtio: Update migration docs
virtio-gpu: Wrap in vmstate
virtio-gpu: Use migrate_add_blocker for virgl migration blocking
virtio-input: Wrap in vmstate
9pfs: Wrap in vmstate
virtio-serial: Wrap in vmstate
virtio-net: Wrap in vmstate
virtio-balloon: Wrap in vmstate
virtio-rng: Wrap in vmstate
virtio-blk: Wrap in vmstate
virtio-scsi: Wrap in vmstate
virtio: Migration helper function and macro
virtio-serial: Remove old migration version support
virtio-net: Remove old migration version support
virtio-scsi: Replace HandleOutput typedef
Revert "mirror: Workaround for unexpected iohandler events during completion"
virtio-scsi: Call virtio_add_queue_aio
virtio-blk: Call virtio_add_queue_aio
virtio: Introduce virtio_add_queue_aio
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Forcibly convert it to a vmstate wrapper; proper conversion
comes later.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtio-net has had version 11 since 0ce0e8f4 in 2009
(v0.11.0-rc0-1480-g0ce0e8f) - remove the code to support loading
anything earlier.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MhfL
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-qapi-2016-07-19' into staging
QAPI patches for 2016-07-19
# gpg: Signature made Tue 19 Jul 2016 19:35:27 BST
# gpg: using RSA key 0x3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-qapi-2016-07-19:
net: Use correct type for bool flag
qapi: Change Netdev into a flat union
block: Simplify drive-mirror
block: Simplify block_set_io_throttle
qapi: Implement boxed types for commands/events
qapi: Plumb in 'boxed' to qapi generator lower levels
qapi-event: Simplify visit of non-implicit data
qapi: Drop useless gen_err_check()
qapi: Add type.is_empty() helper
qapi: Hide tag_name data member of variants
qapi: Special case c_name() for empty type
qapi: Require all branches of flat union enum to be covered
net: use Netdev instead of NetClientOptions in client init
qapi: change QmpInputVisitor to QSLIST
qapi: change QmpOutputVisitor to QSLIST
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a mostly-mechanical conversion that creates a new flat
union 'Netdev' QAPI type that covers all the branches of the
former 'NetClientOptions' simple union, where the branches are
now listed in a new 'NetClientDriver' enum rather than generated
from the simple union. The existence of a flat union has no
change to the command line syntax accepted for new code, and
will make it possible for a future patch to switch the QMP
command to parse a boxed union for no change to valid QMP; but
it does have some ripple effect on the C code when dealing with
the new types.
While making the conversion, note that the 'NetLegacy' type
remains unchanged: it applies only to legacy command line options,
and will not be ported to QMP, so it should remain a wrapper
around a simple union; to avoid confusion, the type named
'NetClientOptions' is now gone, and we introduce 'NetLegacyOptions'
in its place. Then, in the C code, we convert from NetLegacy to
Netdev as soon as possible, so that the bulk of the net stack
only has to deal with one QAPI type, not two. Note that since
the old legacy code always rejected 'hubport', we can just omit
that branch from the new 'NetLegacyOptions' simple union.
Based on an idea originally by Zoltán Kővágó <DirtY.iCE.hu@gmail.com>:
Message-Id: <01a527fbf1a5de880091f98cf011616a78adeeee.1441627176.git.DirtY.iCE.hu@gmail.com>
although the sed script in that patch no longer applies due to
other changes in the tree since then, and I also did some manual
cleanups (such as fixing whitespace to keep checkpatch happy).
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1468468228-27827-13-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Fixup from Eric squashed in]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
e1000e needs net_tx_pkt.o and net_rx_pkt.o too.
Cc: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Cc: Leonid Bloch <leonid.bloch@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Dmitry Fleytman