This allows increasing the rx queue size up to 1024: unlike with tx,
guests don't put in huge S/G lists into RX so the risk of running into
the max 1024 limitation due to some off-by-one seems small.
It's helpful for users like OVS-DPDK which don't do any buffering on the
host - 1K roughly matches 500 entries in tun + 256 in the current rx
queue, which seems to work reasonably well. We could probably make do
with ~750 entries but virtio spec limits us to powers of two.
It might be a good idea to specify an s/g size limit in a future
version.
It also might be possible to make the queue size smaller down the road, 64
seems like the minimal value which will still work (as guests seem to
assume a queue full of 1.5K buffers is enough to process the largest
incoming packet, which is ~64K). No one actually asked for this, and
with virtio 1 guests can reduce ring size without need for host
configuration, so don't bother with this for now.
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Jason Wang <jasowang@redhat.com>
Suggested-by: Patrik Hermansson <phermansson@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
QEMU prints an error message and exits when the device enters an invalid
state. Terminating the process is heavy-handed. The guest may still be
able to function even if there is a bug in a virtio guest driver.
Moreover, exiting is a bug in nested virtualization where a nested guest
could DoS other nested guests by killing a pass-through virtio device.
I don't think this configuration is possible today but it is likely in
the future.
If the broken flag is set, do not process virtqueues or write back used
descriptors. The broken flag can be cleared again by resetting the
device.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently, devices are plugged before features are negotiated.
If the backend doesn't support VIRTIO_F_VERSION_1, the transport
needs to rewind some settings.
This is the case for CCW, for which a post_plugged callback had
been introduced, where max_rev field is just updated if
VIRTIO_F_VERSION_1 is not supported by the backend.
For PCI, implementing post_plugged would be much more
complicated, so it needs to know whether the backend supports
VIRTIO_F_VERSION_1 at plug time.
Currently, nothing is done for PCI. Modern capabilities get
exposed to the guest even if VIRTIO_F_VERSION_1 is not supported
by the backend, which confuses the guest.
This patch replaces existing post_plugged solution with an
approach that fits with both transports.
Features negotiation is performed before ->device_plugged() call.
A pre_plugged callback is introduced so that the transports can
set their supported features.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-stable@nongnu.org
Tested-by: Cornelia Huck <cornelia.huck@de.ibm.com> [ccw]
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Unused function declarations were found using a simple gcc plugin and
manually verified by grepping the sources.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Implement the new virtio sockets device for host<->guest communication
using the Sockets API. Most of the work is done in a vhost kernel
driver so that virtio-vsock can hook into the AF_VSOCK address family.
The QEMU vhost-vsock device handles configuration and live migration
while the rx/tx happens in the vhost_vsock.ko Linux kernel driver.
The vsock device must be given a CID (host-wide unique address):
# qemu -device vhost-vsock-pci,id=vhost-vsock-pci0,guest-cid=3 ...
For more information see:
http://qemu-project.org/Features/VirtioVsock
[Endianness fixes and virtio-ccw support by Claudio Imbrenda
<imbrenda@linux.vnet.ibm.com>]
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
[mst: rebase to master]
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtqueue_discard() requires a VirtQueueElement but virtio-balloon does
not migrate its in-use element. Introduce a new function that is
similar to virtqueue_discard() but doesn't require a VirtQueueElement.
This will allow virtio-balloon to access element again after migration
with the usual proviso that the guest may have modified the vring since
last time.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Roman Kagan <rkagan@virtuozzo.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The virtio-gpu.h file defines a macro VIRTIO_GPU_FILL_CMD
which includes a call to qemu_log_mask, but does not
include qemu/log.h. In a default configure, it is lucky
and gets qemu/log.h indirectly due to the 'log' trace
backend being enabled. If that trace backend is disabled
though, eg
./configure --enable-trace-backends=nop
Then the build will fail:
In file included from /home/berrange/src/virt/qemu/hw/display/virtio-gpu-3d.c:19:0:
/home/berrange/src/virt/qemu/hw/display/virtio-gpu-3d.c: In function ‘virgl_cmd_create_resource_2d’:
/home/berrange/src/virt/qemu/include/hw/virtio/virtio-gpu.h:138:13: error: implicit declaration of function ‘qemu_log_mask’ [-Werror=implicit-function-declaration]
qemu_log_mask(LOG_GUEST_ERROR, \
^
/home/berrange/src/virt/qemu/hw/display/virtio-gpu-3d.c:34:5: note: in expansion of macro ‘VIRTIO_GPU_FILL_CMD’
VIRTIO_GPU_FILL_CMD(c2d);
^~~~~~~~~~~~~~~~~~~
/home/berrange/src/virt/qemu/hw/display/virtio-gpu-3d.c:34:5: error: nested extern declaration of ‘qemu_log_mask’ [-Werror=nested-externs]
In file included from /home/berrange/src/virt/qemu/hw/display/virtio-gpu-3d.c:19:0:
/home/berrange/src/virt/qemu/include/hw/virtio/virtio-gpu.h:138:27: error: ‘LOG_GUEST_ERROR’ undeclared (first use in this function)
qemu_log_mask(LOG_GUEST_ERROR, \
[snip many more errors]
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1470648700-3474-1-git-send-email-berrange@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Not all vhost-user backends support ops->vhost_net_set_backend(). It is
a nicer to provide an assert/error than to crash trying to
call. Furthermore, it improves a bit the code by hiding vhost_ops
details.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virgl conditionally registers a vmstate as unmigratable when virgl
is enabled; instead use the migrate_add_blocker mechanism.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
To make conversion of virtio devices to VMState simple
at first add a helper function for the simple virtio_save
case and a helper macro that defines the VMState structure.
These will probably go away or change as more of the virtio
code gets converted.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is a new common one in virtio.h, use it.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Using this function instead of virtio_add_queue marks the vq as aio
based. This differentiation will be useful in later patches.
Distinguish between virtqueue processing in the iohandler context and main loop
AioContext. iohandler context is isolated from AioContexts and therefore does
not run during aio_poll().
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
The function pointer signature has been repeated a few times, using a
typedef may make coding easier.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Header guard symbols should match their file name to make guard
collisions less likely. Offenders found with
scripts/clean-header-guards.pl -vn.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
This patch add the capability of basic vhost net busy polling which is
supported by recent kernel. User could configure the maximum number of
us that could be spent on busy polling through a new property of tap
"poll-us".
Cc: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
In virgl_cmd_resource_flush(), when several consoles are updated, it
needs to keep blocking until all spice gl draws are done. This fixes an
assert() in spice when using multiple monitors with virgl.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 1465911849-30423-2-git-send-email-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Multiqueue virtio-blk can be enabled as follows:
qemu -device virtio-blk-pci,num-queues=8
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-8-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Multiqueue requires that each request knows to which virtqueue it
belongs.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-5-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The num_queues field is always 1 for the time being. A later patch will
make it a configurable device property so that multiqueue can be
enabled.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-2-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
All users have been converted to the new ioevent callbacks.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce a set of ioeventfd callbacks on the virtio-bus level
that can be implemented by the individual transports. At the
virtio-bus level, do common handling for host notifiers (which
is actually most of it).
Two things of note:
- When setting the host notifier, we only switch from/to the
generic ioeventfd handler. This fixes a latent bug where we
had no ioeventfd assigned for a certain window.
- We always iterate over all possible virtio queues, even though
ccw (currently) has a lower limit. It does not really matter
here.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJXVtmBAAoJEJykq7OBq3PI+eIH/3sx898eSWy9GcNddxvt9PwZ
XB4R0gVG3dcGupaRFvMV3C6kLbx+5YykdZTU5heN7R3k3pBNVdPlbYhAy4KnNQqJ
SPNTk2Y2yH4VtmjIJpl2bJsYbnxQN26gFaMWrs8UzFRVeDQjT0K0OyO5yHlVkDtE
gOMA6zTQ94L0wj3g3pz8PPOGzJ/mA3MvMq+Af0h7d4iiwUqSGfZVxOQ7eS92vdmb
VkSFOJSbckOb1k2IC9uwYpvaJR3KFp7RBY2joPYoD/kHv41oLRZ06ceHEuYWYGRK
9aLiXsWIfXijKTynbbB0HeLcUKvHZok39zWl9d0zNtZ3q7Akuz94aWvbqHABG+Y=
=1Q5r
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/block-pull-request' into staging
# gpg: Signature made Tue 07 Jun 2016 15:26:09 BST
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
* remotes/stefanha/tags/block-pull-request:
throttle: refuse iops-size without iops-total/read/write
block: Drop bdrv_ioctl_bh_cb
block: Move BlockRequest type to io.c
block/io: optimize bdrv_co_pwritev for small requests
iostatus: fix comments for block_job_iostatus_reset
block/io: Remove unused bdrv_aio_write_zeroes()
virtio: drop duplicate virtio_queue_get_id() function
virtio-scsi: Remove op blocker for dataplane
virtio-blk: Remove op blocker for dataplane
blockdev-backup: Don't move target AioContext if it's attached
blockdev-backup: Use bdrv_lookup_bs on target
tests: avoid coroutine pool test crash
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The virtio_queue_get_id() function is the lesser used duplicate of
virtio_get_queue_index(). Use the latter instead.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1463767461-17922-1-git-send-email-stefanha@redhat.com
The previous patch dropped all op blockers from virtio-blk data plane.
The situation of virtio-scsi is exactly the same it can drop them too.
Signed-off-by: Fam Zheng <famz@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1463969978-24970-5-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Paolo's recent cpu.h cleanups broke legacy virtio for ppc64 LE guests (and
arm BE guests as well, even if I have not verified that). Especially, commit
"33c11879fd42 qemu-common: push cpu.h inclusion out of qemu-common.h" has
the side-effect of silently hiding the TARGET_IS_BIENDIAN macro from the
virtio memory accessors, and thus fully disabling support of endian changing
targets.
To be sure this cannot happen again, let's gather all the bi-endian bits
where they belong in include/hw/virtio/virtio-access.h.
The changes in hw/virtio/vhost.c are safe because vhost_needs_vring_endian()
is not called on a hot path and non bi-endian targets will return false
anyway.
While here, also rename TARGET_IS_BIENDIAN to be more precise: it is only for
legacy virtio and bi-endian guests.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Store some additional state for cursor and resource backing storage,
so we can write out and reload things. Implement vmsave+vmload for
2d mode. Continue blocking live migration in 3d/virgl mode.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1464009727-7753-1-git-send-email-kraxel@redhat.com
The value is defined in virtio_gpu.h already (changing from 4 to 16).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 1463653560-26958-6-git-send-email-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Usually, Random Number Generator is abbreviated to RNG/rng.
so replacing RndRandom with RngRandom seems more reasonable
and keep consistent with RngBackend.
Signed-off-by: Wei Jiangang <weijg.fnst@cn.fujitsu.com>
Reviewed-by: Pankaj Gupta <pagupta@redhat.com>
Message-Id: <1460684168-5403-1-git-send-email-weijg.fnst@cn.fujitsu.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
VIRTIO_INPUT_CFG_ABS_INFO was not implemented for pass-through input
devices. This patch follows the existing design and pre-fetches the
config for all absolute axes using EVIOCGABS at realize time.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Message-id: 1460558603-18331-1-git-send-email-lprosek@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
"_x" must be "(_x)" otherwise things fail if you pass in expressions.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1460440299-26654-1-git-send-email-kraxel@redhat.com
Eliminating the reentrancy is actually a nice thing that we can do
with the API that Michael proposed, so let's make it first class.
This also hides the complex assign/set_handler conventions from
callers of virtio_queue_aio_set_host_notifier_handler, which in
fact was always called with assign=true.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In addition to handling IO in vcpu thread and in io thread, dataplane
introduces yet another mode: handling it by AioContext.
This reuses the same handler as previous modes, which triggers races as
these were not designed to be reentrant. Use a separate handler just
for aio, and disable regular handlers when dataplane is active.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In addition to handling IO in vcpu thread and in io thread, dataplane
introduces yet another mode: handling it by AioContext.
This reuses the same handler as previous modes, which triggers races as
these were not designed to be reentrant. Use a separate handler just
for aio, and disable regular handlers when dataplane is active.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In addition to handling IO in vcpu thread and in io thread, blk dataplane
introduces yet another mode: handling it by AioContext.
Currently, this reuses the same handler as previous modes,
which triggers races as these were not designed to be reentrant.
Add instead a separate handler just for aio; this will make
it possible to disable regular handlers when dataplane is active.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add two missing checks for s->dataplane_fenced. In one case, QEMU
would skip injecting an IRQ due to a write to an uninitialized
EventNotifier's file descriptor.
In the second case, the dataplane_disabled field was used by mistake;
in fact after fixing this occurrence it is completely unused.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We must not call virtio_blk_data_plane_notify if dataplane is
disabled: we would hit a segmentation fault in notify_guest_bh as
s->guest_notifier has not been setup and is NULL.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes all over the place.
virtio dataplane migration support.
Old q35 machine types removed.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWzuKeAAoJECgfDbjSjVRpGzIH/1Tz6CoEq1rowiyVJ9B80oQU
gDI2YWnJDSwJllmAF0rmoPRBQR8op3ZETZiCAcADHoZ7kdBNWGbyQeaDrrEPH7Q/
rCDVt8Q3g80vs89aWKG0nQ16J2MW5TbkuiQw7pjQSdc9AbUdWpUqSiWnpZ+sPAql
6DuVpjQ4/rN2alucXoa1Sir8KDDV7kBuY8U6/KoY890qzh842dv2523qvuCza9yR
KX8Imj3oQAFjFSv5t1aOD3yYvWFd73EsReHPLGb1JtsVr/6wjs0sFUyA3JicBgnT
+kWoSObWikfDY69HnqTkJpkun6woMM3zW5h2SkUBf9QP3yqLfGIp9uSriNN84Ak=
=KXyh
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
vhost, virtio, pci, pc
Fixes all over the place.
virtio dataplane migration support.
Old q35 machine types removed.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 25 Feb 2016 11:16:46 GMT using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream: (21 commits)
q35: No need to check gigabyte_align
q35: Remove unused q35-acpi-dsdt.aml file
ich9: Remove enable_tco arguments from init functions
machine: Remove no_tco field
q35: Remove old machine versions
tests/vhost-user-bridge: fix build on 32 bit systems
vring: remove
virtio-scsi: do not use vring in dataplane
virtio-blk: do not use vring in dataplane
virtio-blk: fix "disabled data plane" mode
virtio: export vring_notify as virtio_should_notify
virtio: add AioContext-specific function for host notifiers
vring: make vring_enable_notification return void
block-migration: acquire AioContext as necessary
pci core: function pci_bus_init() cleanup
pci core: function pci_host_bus_register() cleanup
balloon: Use only 'pc-dimm' type dimm for ballooning
virtio-balloon: rewrite get_current_ram_size()
move get_current_ram_size to virtio-balloon.c
vhost-user: don't merge regions with different fds
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
In disabled mode, virtio-blk dataplane seems to be enabled, but flow
actually goes through the normal virtio path. This patch simplifies a bit
the handling of disabled mode. In disabled mode, virtio_blk_handle_output
might be called even if s->dataplane is not NULL.
This is a bit tricky, because the current check for s->dataplane will
always trigger, causing a continuous stream of calls to
virtio_blk_data_plane_start. Unfortunately, these calls will not
do anything. To fix this, set the "started" flag even in disabled
mode, and skip virtio_blk_data_plane_start if the started flag is true.
The resulting changes also prepare the code for the next patch, were
virtio-blk dataplane will reuse the same virtio_blk_handle_output function
as "regular" virtio-blk.
Because struct VirtIOBlockDataPlane is opaque in virtio-blk.c, we have
to move s->dataplane->started inside struct VirtIOBlock.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Virtio dataplane needs to trigger the irq manually through the
guest notifier. Export virtio_should_notify so that it can be
used around event_notifier_set.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
This is used to register ioeventfd with a dataplane thread.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Make the API more similar to the regular virtqueue API. This will
help when modifying the code to not use vring.c anymore.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
NB: If this commit breaks compilation for your out-of-tree
patchseries or fork, then you need to make sure you add
#include "qemu/osdep.h" to any new .c files that you have.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Michael S. Tsirkin