We document that for qcow2 persistent bitmaps, the name cannot exceed
1023 bytes. It is inconsistent if transient bitmaps do not have to
abide by the same limit, and it is unlikely that any existing client
even cares about using bitmap names this long. It's time to codify
that ALL bitmaps managed by qemu (whether persistent in qcow2 or not)
have a documented maximum length.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20191114024635.11363-3-eblake@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
As long as we limit NBD names to 256 bytes (the bare minimum permitted
by the standard), stack-allocation works for parsing a name received
from the client. But as mentioned in a comment, we eventually want to
permit up to the 4k maximum of the NBD standard, which is too large
for stack allocation; so switch everything in the server to use heap
allocation. For now, there is no change in actually supported name
length.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20191114024635.11363-2-eblake@redhat.com>
[eblake: fix uninit variable compile failure]
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Coverity warns that we store the address of a stack variable through a
pointer passed in by the caller, which would let the caller trivially
trigger use-after-free if that stored value is still present when we
finish execution. However, the way coroutines work is that after our
call to qemu_coroutine_yield(), control is temporarily continued in
the caller prior to our function concluding, and in order to resume
our coroutine, the caller must poll until the variable has been set to
NULL. Thus, we can add an assert that we do not leak stack storage to
the caller on function exit.
Fixes: Coverity CID 1406474
CC: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20191111203524.21912-1-eblake@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The test for an NBD client. The NBD server is disconnected after the
client write request. The NBD client should reconnect and complete
the write operation.
Suggested-by: Denis V. Lunev <den@openvz.org>
Suggested-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Message-Id: <1573529976-815699-1-git-send-email-andrey.shinkevich@virtuozzo.com>
Test that doing a second blockdev-snapshot doesn't make the first
overlay's backing file go away.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Peter Krempa <pkrempa@redhat.com>
bs->options and bs->explicit_options shouldn't contain any options for
child nodes. bdrv_open_inherited() takes care to remove any options that
match a child name after opening the image and the same is done when
reopening.
However, we miss the case of 'backing': null, which is a child option,
but results in no child being created. This means that a 'backing': null
remains in bs->options and bs->explicit_options.
A typical use for 'backing': null is in live snapshots: blockdev-add for
the qcow2 overlay makes sure not to open the backing file (because it is
already opened and blockdev-snapshot will attach it). After doing a
blockdev-snapshot, bs->options and bs->explicit_options become
inconsistent with the actual state (bs has a backing file now, but the
options still say null). On the next occasion that the image is
reopened, e.g. switching it from read-write to read-only when another
snapshot is taken, the option will take effect again and the node
incorrectly loses its backing file.
Fix bdrv_open_inherited() to remove the 'backing' option from
bs->options and bs->explicit_options even for the case where it
specifies that no backing file is wanted.
Reported-by: Peter Krempa <pkrempa@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Tested-by: Peter Krempa <pkrempa@redhat.com>
The variable for error messages to be displayed is $results, not
$reason. Fix 'check' to print the "no qualified output" error message
again instead of having a failure without any message telling the user
why it failed.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
From the two values compared, make it obvious which is found at path, and
which is expected.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Due to lchs support merge in upstream seabios gone wrong (applied v3
instead of v4) here is another seabios snapshot update with the
mis-merge fixed up, so lchs support should actually work in -rc2.
Also picked up two tpm bugfixes.
git shortlog from previous snapshot
===================================
Gerd Hoffmann (4):
Revert "geometry: Apply LCHS values for boot devices"
Revert "config: Add toggle for bootdevice information"
Revert "geometry: Add boot_lchs_find_*() utility functions"
Revert "geometry: Read LCHS from fw_cfg"
Sam Eiderman (4):
geometry: Read LCHS from fw_cfg
boot: Build ata and scsi paths in function
geometry: Add boot_lchs_find_*() utility functions
geometry: Apply LCHS values for boot devices
Stefan Berger (2):
tpm: Require a response to have minimum size of a valid response header
tcgbios: Check for enough bytes returned from TPM2_GetCapability
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
With the Quadra 800 emulation, mos6522 timers processing can consume
until 70% of the host CPU time with an idle guest (I guess the problem
should also happen with PowerMac emulation).
On a recent system, it can be painless (except if you look at top), but
on an old host like a PowerMac G5 the guest kernel can be terribly slow
during the boot sequence (for instance, unpacking initramfs can take 15
seconds rather than only 3 seconds).
We can avoid this CPU overload by enabling QEMU internal timers only if
the mos6522 counter interrupts are enabled. Sometime the guest kernel
wants to read the counters values, but we don't need the timers to
update the counters.
With this patch applied, an idle Q800 consumes only 3% of host CPU time
(and the guest can boot in a decent time).
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20191102154919.17775-1-laurent@vivier.eu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
We have to set the default model of all machine classes, not just for
the active one. Otherwise, "query-machines" will indicate the wrong
CPU model (e.g. "power9_v2.0-powerpc64-cpu" instead of
"host-powerpc64-cpu") as "default-cpu-type".
s390x already fixed this in de60a92e "s390x/kvm: Set default cpu model for
all machine classes". This patch applies a similar fix for the pseries-*
machine types on ppc64.
Doing a
{"execute":"query-machines"}
under KVM now results in
{
"hotpluggable-cpus": true,
"name": "pseries-4.2",
"numa-mem-supported": true,
"default-cpu-type": "host-powerpc64-cpu",
"is-default": true,
"cpu-max": 1024,
"deprecated": false,
"alias": "pseries"
},
{
"hotpluggable-cpus": true,
"name": "pseries-4.1",
"numa-mem-supported": true,
"default-cpu-type": "host-powerpc64-cpu",
"cpu-max": 1024,
"deprecated": false
},
...
Libvirt probes all machines via "-machine none,accel=kvm:tcg" and will
currently see the wrong CPU model under KVM.
Reported-by: Jiři Denemark <jdenemar@redhat.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Jiri Denemark <jdenemar@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Since "spapr: Render full FDT on ibm,client-architecture-support" we build
the entire flatten device tree (FDT) twice - at the reset time and
when "ibm,client-architecture-support" (CAS) is called. The full FDT from
CAS is then applied on top of the SLOF internal device tree.
This is mostly ok, however there is a case when the QEMU is started with
-initrd and for some reason the guest decided to move/unpack the init RAM
disk image - the guest correctly notifies SLOF about the change but
at CAS it is overridden with the QEMU initial location addresses and
the guest may fail to boot if the original initrd memory was changed.
This fixes the problem by only adding the /chosen node at the reset time
to prevent the original QEMU's linux,initrd-start/linux,initrd-end to
override the updated addresses.
This only treats /chosen differently as we know there is a special case
already and it is unlikely anything else will need to change /chosen at CAS
we are better off not touching /chosen after we handed it over to SLOF.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20191024041308.5673-1-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
CPU_FOREACH() can race with vCPU hotplug/unplug on sPAPR machines, ie.
we may try to print out info about a vCPU with a NULL presenter pointer.
Check that in order to prevent QEMU from crashing.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157192725327.3146912.12047076483178652551.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
When a VCPU gets connected to the XIVE interrupt controller, we add a
const link targetting the CPU object to the TCTX object. Similar links
are added to the ICP object when using the XICS interrupt controller.
As explained in <qom/object.h>:
* The caller must ensure that @target stays alive as long as
* this property exists. In the case @target is a child of @obj,
* this will be the case. Otherwise, the caller is responsible for
* taking a reference.
We're in the latter case for both XICS and XIVE. Add the missing
calls to object_ref() and object_unref().
This doesn't fix any known issue because the life cycle of the TCTX or
ICP happens to be shorter than the one of the CPU or XICS fabric, but
better safe than sorry.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <157192724770.3146912.15400869269097231255.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
SpaprInterruptControllerClass and PnvChipClass have an intc_create() method
that calls the appropriate routine, ie. icp_create() or xive_tctx_create(),
to establish the link between the VCPU and the presenter component of the
interrupt controller during realize.
There aren't any symmetrical call to be called when the VCPU gets unrealized
though. It is assumed that object_unparent() is the only thing to do.
This is questionable because the parenting logic around the CPU and
presenter objects is really an implementation detail of the interrupt
controller. It shouldn't be open-coded in the machine code.
Fix this by adding an intc_destroy() method that undoes what was done in
intc_create(). Also NULLify the presenter pointers to avoid having
stale pointers around. This will allow to reliably check if a vCPU has
a valid presenter.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157192724208.3146912.7254684777515287626.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
This contains a handful of patches that I'd like to target for 4.2:
* OpenSBI upgrade to 0.5
* Increase in the flash size of the virt board.
* A non-functional cleanup.
* A cleanup to our MIP handling that avoids atomics.
This passes "make check" and boots OpenEmbedded for me.
-----BEGIN PGP SIGNATURE-----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=vwgx
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/palmer/tags/riscv-for-master-4.2-rc2' into staging
RISC-V Fixes for 4.2-rc2
This contains a handful of patches that I'd like to target for 4.2:
* OpenSBI upgrade to 0.5
* Increase in the flash size of the virt board.
* A non-functional cleanup.
* A cleanup to our MIP handling that avoids atomics.
This passes "make check" and boots OpenEmbedded for me.
# gpg: Signature made Thu 14 Nov 2019 18:39:27 GMT
# gpg: using RSA key 00CE76D1834960DFCE886DF8EF4CA1502CCBAB41
# gpg: issuer "palmer@dabbelt.com"
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
* remotes/palmer/tags/riscv-for-master-4.2-rc2:
riscv/virt: Increase flash size
opensbi: Upgrade from v0.4 to v0.5
target/riscv: Remove atomic accesses to MIP CSR
remove unnecessary ifdef TARGET_RISCV64
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Coreboot developers have requested that they have at least 32MB of flash
to load binaries. We currently have 32MB of flash, but it is split in
two to allow loading two flash binaries. Let's increase the flash size
from 32MB to 64MB to ensure we have a single region that is 32MB.
No QEMU release has include flash in the RISC-V virt machine, so this
isn't a breaking change.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This release has:
Lot of critical fixes
Hypervisor extension support
SBI v0.2 base extension support
Debug prints support
Handle traps when doing unpriv load/store
Allow compiling without FP support
Use git describe to generate boot-time banner
Andes AE350 platform support
ShortLog:
Anup Patel (14):
platform: sifive/fu540: Move FDT further up
lib: Allow compiling without FP support
lib: Introduce sbi_dprintf() API
lib: Use sbi_dprintf() for invalid CSRs
lib: Handle traps when doing unpriv load/store in get_insn()
lib: Delegate supervisor ecall to HS-mode when H extension available
lib: Extend sbi_hart_switch_mode() to support hypervisor extension
lib: Extend sbi_trap_redirect() for hypervisor extension
lib: Redirect WFI trapped from VS/VU mode to HS-mode
include: Extend get_insn() to read instruction from VS/VU mode
lib: Emulate HTIMEDELTA CSR for platforms not having TIME CSR
Makefile: Minor fix in OPENSBI_VERSION_GIT
lib: Fix coldboot race condition observed on emulators/simulators
include: Bump-up version to 0.5
Atish Patra (16):
lib: Provide an atomic exchange function unsigned long
lib: Fix race conditions in tlb fifo access.
platform: Remove the ipi_sync method from all platforms.
lib: Fix timer for 32 bit
lib: Support atomic swap instructions
lib: Upgrade to full flush if size is at least threshold
docs: Update the fu540 platform guide as per U-Boot documents.
lib: Change tlb range flush threshold to 4k page instead of 1G
lib: provide a platform specific tlb range flush threshold
lib: Fix tlb flush range limit value
Test: Move test payload related code out of interface header
lib: Align error codes as per SBI specification.
lib: Rename existing SBI implementation as 0.1.
lib: Remove redundant variable assignment
lib: Implement SBI v0.2
lib: Provide a platform hook to implement vendor specific SBI extensions.
Bin Meng (6):
platform: sifive: fu540: Use standard value string for cpu node status
README: Document 32-bit / 64-bit images build
treewide: Use conventional names for 32-bit and 64-bit
platform: sifive: fu540: Expand FDT size before any patching
firmware: Use macro instead of magic number for boot status
docs: platform: Update descriptions for qemu/sifive_u support
Damien Le Moal (4):
kendryte/k210: Use sifive UART driver
kendryte/k210: remove sysctl code
README: Update license information
kendryte/k210: remove unused file
Georg Kotheimer (1):
utils: Use cpu_to_fdt32() when writing to fdt
Jacob Garber (4):
lib: Use bitwise & instead of boolean &&
lib: Use correct type for return value
lib: Prevent unintended sign extensions
lib: Correct null pointer check
Lukas Auer (1):
firmware: do not use relocated _boot_status before it is valid
Nylon Chen (3):
firmware: Fix the loop condition of _wait_relocate_copy_done section
platform: Add Andes AE350 initial support
scripts: Add AE350 to platform list in the binary archive script
Palmer Dabbelt (1):
Include `git describe` in OpenSBI
Zong Li (1):
Write MSIP by using memory-mapped control register
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Instead of relying on atomics to access the MIP register let's update
our helper function to instead just lock the IO mutex thread before
writing. This follows the same concept as used in PPC for handling
interrupts
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
seabios 1.13 will be released later this month. This patch updates the
seabios submodule and binaries in qemu to a snapshot of git master.
That will increase the test coverage of the upcoming seabios release and
will also make the number of changes smaller when we update to the final
1.13 release during qemu code freeze for 4.2.
v3: add ahci bugfix
v2: build binaries with gcc 4.8.5 instead of gcc 8.3.1 (rhel7).
git shortlog rel-1.12.1..
=========================
David Woodhouse (2):
csm: Sanitise alignment constraint in Legacy16GetTableAddress
csm: Fix boot priority translation
Denis Plotnikov (1):
virtio: extend virtio queue size to 256
Gerd Hoffmann (21):
vga: move modelist from bochsvga.c to new svgamodes.c
vga: make memcpy_high() public
vga: add atiext driver
vga: add ati bios tables
vbe: add edid support.
ati: add edid support.
bochsvga: add edid support.
bochsdisplay: add edid support.
bochsdisplay: parse resolution from edid.
add get_keystroke_full() helper
bootmenu: add support for more than 9 entries
optionrom: disallow int19 redirect for pnp roms.
ati-vga: make less verbose
ati-vga: fix ati_read()
ati-vga: make i2c register and bits configurable
ati-vga: try vga ddc first
ati-vga: add rage128 edid support
bochsdisplay: add copyright and license to bochsdisplay.c
ramfb: add copyright and license to ramfb.c
cp437: add license to cp437.c
ahci: zero-initialize port struct
Joseph Pacheco-Corwin (1):
bootsplash: Added support for 16/24/32bpp in one function
Kevin O'Connor (10):
output: Avoid thunking to 16bit mode in printf() if no vgabios
docs: Update mailing list archive links
docs: Fix cut-and-paste error in Mailinglist.md archive link
usb-ehci: Clear pipe token on pipe reallocate
pciinit: Use %pP shorthand for printing device ids in intel_igd_setup()
virtio-pci: Use %pP format in dprintf() calls
Makefile: Build with -Wno-address-of-packed-member
svgamodes: Add copyright notice to vgasrc/svgamodes.c
docs: Add developer-certificate-of-origin
docs: Note release date for v1.12.1
Liran Alon (1):
pvscsi: ring_desc do not have to be page aligned
Sam Eiderman (6):
smbios: Add missing zero byte to Type 0
geometry: Read LCHS from fw_cfg
boot: Reorder functions in boot.c
geometry: Add boot_lchs_find_*() utility functions
config: Add toggle for bootdevice information
geometry: Apply LCHS values for boot devices
Stefan Berger (2):
tcgbios: Use table to convert hash to buffer size
tcgbios: Implement TPM 2.0 menu item to activate and deactivate PCR banks
Stefano Garzarella (1):
qemu: avoid debug prints if debugcon is not enabled
Stephen Douthit (1):
tpm: Check for TPM related ACPI tables before attempting hw probe
Uwe Kleine-König (3):
cbvga: reuse svga modes definitions from svgamodes.c
Add additional resolutions for 16:9 displays: 1600x900 and 2560x1440
Remove dos line endings introduced in the last two commits
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
stime() has been withdrawn from glibc
(12cbde1dae6f "Use clock_settime to implement stime; withdraw stime.")
Implement the target stime() syscall using host
clock_settime(CLOCK_REALTIME, ...) as it is done internally in glibc.
Tested qemu-ppc/x86_64 with:
#include <time.h>
#include <stdio.h>
int main(void)
{
time_t t;
int ret;
/* date -u -d"2019-11-12T15:11:00" "+%s" */
t = 1573571460;
ret = stime(&t);
printf("ret %d\n", ret);
return 0;
}
# date; ./stime; date
Tue Nov 12 14:18:32 UTC 2019
ret 0
Tue Nov 12 15:11:00 UTC 2019
Buglink: https://bugs.launchpad.net/qemu/+bug/1852115
Reported-by: Cole Robinson <crobinso@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20191112142556.6335-1-laurent@vivier.eu>
Plug temp leak around eval_cond_jmp().
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Plug temp leaks with delay slot setup.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Simplify endian reversion of address also plugging TCG temp
leaks for loads/stores.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
- add plugin API versioning
- tests/vm add netbsd autoinstall
- disable ipmi-bt-test for non-Linux
- single-thread make check
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAl3KwvYACgkQ+9DbCVqe
KkT/gQf/SWEZrH4q+3yjW+QblK9R5VP4l0LNfCkP8wqPQrYj+85KFswyOhKczH81
8aExg+P8zvjKkBTN1xQWBuOqWAUAfo2Nv2EwwCU784qZSi/R5DY9Dzw3kRBWF10V
j81kX9tUSDVAzQ98RVHvQtMe9yjpuyYOX5x+fD3zjpGmgp3it4+2y4+dHQQVDo3P
PM4xXYrn3OhtDyYR919ydCZb7gwk74Hf6VQQBc99QfAJOwiddLPH66fTpuaXcBXH
GUayxplo/zTTrgmdSfgg8lirYJhrZ0nnE0aK05rtPgc5k//WmVAgkSzDM9A0ZIT4
Tryt8Ww7uJ96OwoSjlQ8+kS5ejLlSg==
=wSRI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-and-tcg-121119-1' into staging
Testing and plugins for rc1
- add plugin API versioning
- tests/vm add netbsd autoinstall
- disable ipmi-bt-test for non-Linux
- single-thread make check
# gpg: Signature made Tue 12 Nov 2019 14:34:30 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-and-tcg-121119-1:
tcg plugins: expose an API version concept
.travis.yml: don't run make check with multiple jobs
tests/vm: support sites with sha512 checksums
tests: only run ipmi-bt-test if CONFIG_LINUX
tests/vm: update netbsd to version 8.1
tests/vm: use console_consume for netbsd
tests/vm: add console_consume helper
tests/vm: netbsd autoinstall, using serial console
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a very simple versioning API which allows the plugin
infrastructure to check the API a plugin was built against. We also
expose a min/cur API version to the plugin via the info block in case
it wants to avoid using old deprecated APIs in the future.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Robert Foley <robert.foley@linaro.org>
Let's challenge the convention that doing more at a time helps. It
certainly doesn't tell you unambiguously where in the test cycle you
were before the test hangs and exceeds the job time limit.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
The NetBSD project uses SHA512 for its checksums so lets support that
in the download helper.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This test has been unstable on NetBSD for awhile. It seems the
mechanism used to listen to a random port is a Linux-ism (although a
received wisdom Linux-ism rather than a well documented one). As
working around would add more hard to test complexity to the test I've
gone for the easier option of making it CONFIG_LINUX only.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Cc: Corey Minyard <cminyard@mvista.com>
Cc: Kamil Rytarowski <kamil@netbsd.org>
Use new helper to read all pending console output,
not just a single char. Unblocks installer boot.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20191031085306.28888-4-kraxel@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Helper function to read all console output.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20191031085306.28888-3-kraxel@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Instead of fetching the prebuilt image from patchew download the install
iso and prepare the image locally. Install to disk, using the serial
console. Create qemu user, configure ssh login. Install packages
needed for qemu builds.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Kamil Rytarowski <n54@gmx.com>
Tested-by: Thomas Huth <thuth@redhat.com>
[ehabkost: rebased to latest qemu.git master]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20191031085306.28888-2-kraxel@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
So far, the server leaves the posix shared memory object behind when
terminating, requiring the user to explicitly remove it in order to
start a new instance.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Claudio Fontana <claudio.fontana@suse.com>
Message-Id: <d938a62c-7538-9d2b-cc0a-13b240ab9141@web.de>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
If memory allocation fails when using -mem-path, QEMU is supposed to print
out a message to indicate that fallback to anonymous RAM is deprecated. This
is done with error_printf() which does output buffering. As a consequence,
the message is only printed at the next flush, eg. when quiting QEMU, and
it also lacks a trailing newline:
qemu-system-ppc64: unable to map backing store for guest RAM: Cannot allocate memory
qemu-system-ppc64: warning: falling back to regular RAM allocation
QEMU 4.1.50 monitor - type 'help' for more information
(qemu) q
This is deprecated. Make sure that -mem-path specified path has sufficient resources to allocate -m specified RAM amountgreg@boss02:~/Work/qemu/qemu-spapr$
Add the missing \n to fix both issues.
Fixes: cb79224b7e "deprecate -mem-path fallback to anonymous RAM"
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <157304440026.351774.14607704217028190097.stgit@bahia.lan>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The error message in object_class_property_add() was copied from
object_property_add() in commit 16bf7f522a. Clarify that it is
about a class, not an object.
While here, have the format string in both functions to fit in a
single line for better grep-ability, despite the checkpatch warning.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <157287383591.234942.311840593519058490.stgit@bahia.tlslab.ibm.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Commit 0d5fae3e52 introduced bios-microvm.bin but forgot to add
it to the list of blobs being installed.
Add it to the list of BLOBS that get installed.
Fixes: 0d5fae3e52 "roms: add microvm-bios (qboot) as binary"
Signed-off-by: Bruce Rogers <brogers@suse.com>
[PMD: Reworded description]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-Id: <20191102114346.6445-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Eric Blake