HAD is a mandatory features with SMMUv3.1 if S1P is set, which is
our case. Other 3.1 mandatory features come with S2P which we don't
have.
So let's support HAD and advertise SMMUv3.1 support in AIDR.
HAD support allows the CD to disable hierarchical attributes, ie.
if the HAD0/1 bit is set, the APTable field of table descriptors
walked through TTB0/1 is ignored.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-11-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the support for AIDR register. It currently advertises
SMMU V3.0 spec.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-10-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enhance the smmu_iotlb_inv_iova() helper with range invalidation.
This uses the new fields passed in the NH_VA and NH_VAA commands:
the size of the range, the level and the granule.
As NH_VA and NH_VAA both use those fields, their decoding and
handling is factorized in a new smmuv3_s1_range_inval() helper.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-8-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the moment each entry in the IOTLB corresponds to a page sized
mapping (4K, 16K or 64K), even if the page belongs to a mapped
block. In case of block mapping this unefficiently consumes IOTLB
entries.
Change the value of the entry so that it reflects the actual
mapping it belongs to (block or page start address and size).
Also the level/tg of the entry is encoded in the key. In subsequent
patches we will enable range invalidation. This latter is able
to provide the level/tg of the entry.
Encoding the level/tg directly in the key will allow to invalidate
using g_hash_table_remove() when num_pages equals to 1.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-6-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce a specialized SMMUTLBEntry to store the result of
the PTW and cache in the IOTLB. This structure extends the
generic IOMMUTLBEntry struct with the level of the entry and
the granule size.
Those latter will be useful when implementing range invalidation.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-5-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce the smmu_get_iotlb_key() helper and the
SMMU_IOTLB_ASID() macro. Also move smmu_get_iotlb_key and
smmu_iotlb_key_hash in the IOTLB related code section.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-4-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add two helpers: one to lookup for a given IOTLB entry and
one to insert a new entry. We also move the tracing there.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-3-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Convert legacy SD host controller to the SDBus API
- Move legacy API to a separate "sdcard_legacy.h" header
- Introduce methods to access multiple bytes on SDBus data lines
- Fix 'switch function' group location
- Fix SDSC maximum card size (2GB)
CI jobs result:
https://gitlab.com/philmd/qemu/-/pipelines/180605963
-----BEGIN PGP SIGNATURE-----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=Pefc
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/sd-next-20200821' into staging
SD/MMC patches
- Convert legacy SD host controller to the SDBus API
- Move legacy API to a separate "sdcard_legacy.h" header
- Introduce methods to access multiple bytes on SDBus data lines
- Fix 'switch function' group location
- Fix SDSC maximum card size (2GB)
CI jobs result:
https://gitlab.com/philmd/qemu/-/pipelines/180605963
# gpg: Signature made Fri 21 Aug 2020 18:27:50 BST
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/sd-next-20200821: (23 commits)
hw/sd: Correct the maximum size of a Standard Capacity SD Memory Card
hw/sd: Fix incorrect populated function switch status data structure
hw/sd: Use sdbus_read_data() instead of sdbus_read_byte() when possible
hw/sd: Add sdbus_read_data() to read multiples bytes on the data line
hw/sd: Use sdbus_write_data() instead of sdbus_write_byte when possible
hw/sd: Add sdbus_write_data() to write multiples bytes on the data line
hw/sd: Rename sdbus_read_data() as sdbus_read_byte()
hw/sd: Rename sdbus_write_data() as sdbus_write_byte()
hw/sd: Rename read/write_data() as read/write_byte()
hw/sd: Move sdcard legacy API to 'hw/sd/sdcard_legacy.h'
hw/sd/sdcard: Make sd_data_ready() static
hw/sd/pl181: Replace disabled fprintf()s by trace events
hw/sd/pl181: Do not create SD card within the SD host controller
hw/sd/pl181: Expose a SDBus and connect the SDCard to it
hw/sd/pl181: Use named GPIOs
hw/sd/pl181: Add TODO to use Fifo32 API
hw/sd/pl181: Rename pl181_send_command() as pl181_do_command()
hw/sd/pl181: Replace fprintf(stderr, "*\n") with error_report()
hw/sd/milkymist: Do not create SD card within the SD host controller
hw/sd/milkymist: Create the SDBus at init()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Once an interrupt has been claimed, but before it has been compelted we
shouldn't receive any more pending interrupts. This patche keeps track
of this to ensure that we don't see any more interrupts until it is
completed.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <394c3f070615ff2b4fab61a1cf9cb48c122913b7.1595655188.git.alistair.francis@wdc.com>
It is enough to simply map the SiFive FU540 L2 cache controller
into the MMIO space using create_unimplemented_device(), with an
FDT fragment generated, to make the latest upstream U-Boot happy.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1595227748-24720-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add a sdbus_read_data() method to read multiple bytes on the
data line of a SD bus.
We might improve the tracing later, for now keep logging each
byte individually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200814092346.21825-7-f4bug@amsat.org>
Add a sdbus_write_data() method to write multiple bytes on the
data line of a SD bus.
We might improve the tracing later, for now keep logging each
byte individually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200814092346.21825-5-f4bug@amsat.org>
The sdbus_read_data() method do a single byte access on the data
line of a SD bus. Rename it as sdbus_read_byte() and document it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200814092346.21825-4-f4bug@amsat.org>
The sdbus_write_data() method do a single byte access on the data
line of a SD bus. Rename it as sdbus_write_byte() and document it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200814092346.21825-3-f4bug@amsat.org>
The read/write_data() methods write do a single byte access
on the data line of a SD card. Rename them as read/write_byte().
Add some documentation (not in "hw/sd/sdcard_legacy.h" which we
are going to remove soon).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200814092346.21825-2-f4bug@amsat.org>
omap_mmc.c is the last device left using the legacy sdcard API.
Move the prototype declarations into a separate header, to
make it clear this is a legacy API.
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180216022933.10945-8-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
sd_data_ready() belongs to the legacy API. As its last user has
been converted to the SDBus API, make it static.
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180216022933.10945-7-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
SD/MMC host controllers provide a SD Bus to plug SD cards,
but don't come with SD card plugged in :)
The machine/board object is where the SD cards are created.
Since the PXA2xx is not qdevified, for now create the cards
in pxa270_init() which is the SoC model.
In the future we will move this to the board model.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200705213350.24725-2-f4bug@amsat.org>
With Makefiles that have automatically generated dependencies, you
generated includes are set as dependencies of the Makefile, so that they
are built before everything else and they are available when first
building the .c files.
Alternatively you can use a fine-grained dependency, e.g.
target/arm/translate.o: target/arm/decode-neon-shared.inc.c
With Meson you have only one choice and it is a third option, namely
"build at the beginning of the corresponding target"; the way you
express it is to list the includes in the sources of that target.
The problem is that Meson decides if something is a source vs. a
generated include by looking at the extension: '.c', '.cc', '.m', '.C'
are sources, while everything else is considered an include---including
'.inc.c'.
Use '.c.inc' to avoid this, as it is consistent with our other convention
of using '.rst.inc' for included reStructuredText files. The editorconfig
file is adjusted.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add 5.2 machine types for arm/i440fx/q35/s390x/spapr.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200819144016.281156-1-cohuck@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
CONFIG_XEN is generated by configure and stored in "config-target.h",
which is (obviously) only include for target-specific objects.
This is a problem for target-agnostic objects as CONFIG_XEN is never
defined and xen_enabled() is always inlined as 'false'.
Fix by following the KVM schema, defining CONFIG_XEN_IS_POSSIBLE
when we don't know to force the call of the non-inlined function,
returning the xen_allowed boolean.
Fixes: da278d58a0 ("accel: Move Xen accelerator code under accel/xen/")
Reported-by: Paul Durrant <pdurrant@amazon.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20200804074930.13104-2-philmd@redhat.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The NVIC provides an outbound qemu_irq "SYSRESETREQ" which it signals
when the guest sets the SYSRESETREQ bit in the AIRCR register. This
matches the hardware design (where the CPU has a signal of this name
and it is up to the SoC to connect that up to an actual reset
mechanism), but in QEMU it mostly results in duplicated code in SoC
objects and bugs where SoC model implementors forget to wire up the
SYSRESETREQ line.
Provide a default behaviour for the case where SYSRESETREQ is not
actually connected to anything: use qemu_system_reset_request() to
perform a system reset. This will allow us to remove the
implementations of SYSRESETREQ handling from the boards where that's
exactly what it does, and also fixes the bugs in the board models
which forgot to wire up the signal:
* microbit
* mps2-an385
* mps2-an505
* mps2-an511
* mps2-an521
* musca-a
* musca-b1
* netduino
* netduinoplus2
We still allow the board to wire up the signal if it needs to, in case
we need to model more complicated reset controller logic or to model
buggy SoC hardware which forgot to wire up the line itself. But
defaulting to "reset the system" is more often going to be correct
than defaulting to "do nothing".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200728103744.6909-3-peter.maydell@linaro.org
Mostly devices don't need to care whether one of their output
qemu_irq lines is connected, because functions like qemu_set_irq()
silently do nothing if there is nothing on the other end. However
sometimes a device might want to implement default behaviour for the
case where the machine hasn't wired the line up to anywhere.
Provide a function qemu_irq_is_connected() that devices can use for
this purpose. (The test is trivial but encapsulating it in a
function makes it easier to see where we're doing it in case we need
to change the implementation later.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200728103744.6909-2-peter.maydell@linaro.org
Minor bugfixes all over the places, including one CVE.
Additionally, a fix for an ancient bug in migration -
one has to wonder how come no one noticed.
The fix is also non-trivial since we dare not break all
existing machine types with pci - we have a work around
in the works, for now we just skip the work-around for
old machine types.
Great job by Hogan Wang noticing, debugging and fixing it,
and thanks to Dr. David Alan Gilbert for reviewing the patches.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl8e9CIPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpsAIH/2EEq9rLpjqMJdzRvjq3/UAHsvm42zeTnJl7
81cM887Mrg2Nd7MXFoxurLK5UEehTzlD2DRTvaDFfJaJlrtkPM2QEU2X/6c3syAS
GbmOQaljQtR4zEFE81t84mZQS025Gp0s+uble7KvtXakgp1A/vdu93OEvJkhtRY8
JBdRMlTt2T0eizvHn1obBKjaQN7tAUKl5KagHWxP1ApGU0YibUbrBadpJ18ZcKMl
vwB3dwmoi4f7AjuC0GnxYKp7kC/MMhUPFoDxQKI7d+wMGFnbsAF4sBIN9EZKeOkv
xT2InNSAzk/PTSuQpnDnZQjmrf4dPuL/GNJ8vQk27eaFfVchJyc=
=Bu6o
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio,pci: bugfixes
Minor bugfixes all over the places, including one CVE.
Additionally, a fix for an ancient bug in migration -
one has to wonder how come no one noticed.
The fix is also non-trivial since we dare not break all
existing machine types with pci - we have a work around
in the works, for now we just skip the work-around for
old machine types.
Great job by Hogan Wang noticing, debugging and fixing it,
and thanks to Dr. David Alan Gilbert for reviewing the patches.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon 27 Jul 2020 16:34:58 BST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
virtio-pci: fix virtio_pci_queue_enabled()
MAINTAINERS: Cover the firmware JSON schema
vhost-vdpa :Fix Coverity CID 1430270 / CID 1420267
libvhost-user: Report descriptor index on panic
Fix vhost-user buffer over-read on ram hot-unplug
hw/pci-host: save/restore pci host config register
virtio-mem-pci: force virtio version 1
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In legacy mode, virtio_pci_queue_enabled() falls back to
virtio_queue_enabled() to know if the queue is enabled.
But virtio_queue_enabled() calls again virtio_pci_queue_enabled()
if k->queue_enabled is set. This ends in a crash after a stack
overflow.
The problem can be reproduced with
"-device virtio-net-pci,disable-legacy=off,disable-modern=true
-net tap,vhost=on"
And a look to the backtrace is very explicit:
...
#4 0x000000010029a438 in virtio_queue_enabled ()
#5 0x0000000100497a9c in virtio_pci_queue_enabled ()
...
#130902 0x000000010029a460 in virtio_queue_enabled ()
#130903 0x0000000100497a9c in virtio_pci_queue_enabled ()
#130904 0x000000010029a460 in virtio_queue_enabled ()
#130905 0x0000000100454a20 in vhost_net_start ()
...
This patch fixes the problem by introducing a new function
for the legacy case and calls it from virtio_pci_queue_enabled().
It also calls it from virtio_queue_enabled() to avoid code duplication.
Fixes: f19bcdfedd ("virtio-pci: implement queue_enabled method")
Cc: Jason Wang <jasowang@redhat.com>
Cc: Cindy Lu <lulu@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20200727153319.43716-1-lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The pci host config register is used to save PCI address for
read/write config data. If guest writes a value to config register,
and then QEMU pauses the vcpu to migrate, after the migration, the guest
will continue to write pci config data, and the write data will be ignored
because of new qemu process losing the config register state.
To trigger the bug:
1. guest is booting in seabios.
2. guest enables the SMRAM in seabios:piix4_apmc_smm_setup, and then
expects to disable the SMRAM by pci_config_writeb.
3. after guest writes the pci host config register, QEMU pauses vcpu
to finish migration.
4. guest write of config data(0x0A) fails to disable the SMRAM because
the config register state is lost.
5. guest continues to boot and crashes in ipxe option ROM due to SMRAM
in enabled state.
Example Reproducer:
step 1. Make modifications to seabios and qemu for increase reproduction
efficiency, write 0xf0 to 0x402 port notify qemu to stop vcpu after
0x0cf8 port wrote i440 configure register. qemu stop vcpu when catch
0x402 port wrote 0xf0.
seabios:/src/hw/pci.c
@@ -52,6 +52,11 @@ void pci_config_writeb(u16 bdf, u32 addr, u8 val)
writeb(mmconfig_addr(bdf, addr), val);
} else {
outl(ioconfig_cmd(bdf, addr), PORT_PCI_CMD);
+ if (bdf == 0 && addr == 0x72 && val == 0xa) {
+ dprintf(1, "stop vcpu\n");
+ outb(0xf0, 0x402); // notify qemu to stop vcpu
+ dprintf(1, "resume vcpu\n");
+ }
outb(val, PORT_PCI_DATA + (addr & 3));
}
}
qemu:hw/char/debugcon.c
@@ -60,6 +61,9 @@ static void debugcon_ioport_write(void *opaque, hwaddr addr, uint64_t val,
printf(" [debugcon: write addr=0x%04" HWADDR_PRIx " val=0x%02" PRIx64 "]\n", addr, val);
#endif
+ if (ch == 0xf0) {
+ vm_stop(RUN_STATE_PAUSED);
+ }
/* XXX this blocks entire thread. Rewrite to use
* qemu_chr_fe_write and background I/O callbacks */
qemu_chr_fe_write_all(&s->chr, &ch, 1);
step 2. start vm1 by the following command line, and then vm stopped.
$ qemu-system-x86_64 -machine pc-i440fx-5.0,accel=kvm\
-netdev tap,ifname=tap-test,id=hostnet0,vhost=on,downscript=no,script=no\
-device virtio-net-pci,netdev=hostnet0,id=net0,bus=pci.0,addr=0x13,bootindex=3\
-device cirrus-vga,id=video0,vgamem_mb=16,bus=pci.0,addr=0x2\
-chardev file,id=seabios,path=/var/log/test.seabios,append=on\
-device isa-debugcon,iobase=0x402,chardev=seabios\
-monitor stdio
step 3. start vm2 to accept vm1 state.
$ qemu-system-x86_64 -machine pc-i440fx-5.0,accel=kvm\
-netdev tap,ifname=tap-test1,id=hostnet0,vhost=on,downscript=no,script=no\
-device virtio-net-pci,netdev=hostnet0,id=net0,bus=pci.0,addr=0x13,bootindex=3\
-device cirrus-vga,id=video0,vgamem_mb=16,bus=pci.0,addr=0x2\
-chardev file,id=seabios,path=/var/log/test.seabios,append=on\
-device isa-debugcon,iobase=0x402,chardev=seabios\
-monitor stdio \
-incoming tcp:127.0.0.1:8000
step 4. execute the following qmp command in vm1 to migrate.
(qemu) migrate tcp:127.0.0.1:8000
step 5. execute the following qmp command in vm2 to resume vcpu.
(qemu) cont
Before this patch, we get KVM "emulation failure" error on vm2.
This patch fixes it.
Cc: qemu-stable@nongnu.org
Signed-off-by: Hogan Wang <hogan.wang@huawei.com>
Message-Id: <20200727084621.3279-1-hogan.wang@huawei.com>
Reported-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Plain MAP_FIXED has the undesirable behaviour of splatting exiting
maps so we don't actually achieve what we want when looking for gaps.
We should be using MAP_FIXED_NOREPLACE. As this isn't always available
we need to potentially check the returned address to see if the kernel
gave us what we asked for.
Fixes: ad592e37df ("linux-user: provide fallback pgd_find_hole for bare chroots")
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200724064509.331-9-alex.bennee@linaro.org>
Quoting ISO C99 6.7.8p4, "All the expressions in an initializer for an
object that has static storage duration shall be constant expressions or
string literals".
The compound literal produced by the make_floatx80() macro is not such a
constant expression, per 6.6p7-9. (An implementation may accept it,
according to 6.6p10, but is not required to.)
Therefore using "floatx80_zero" and make_floatx80() for initializing
"f2xm1_table" and "fpatan_table" is not portable. And gcc-4.8 in RHEL-7.6
actually chokes on them:
> target/i386/fpu_helper.c:871:5: error: initializer element is not constant
> { make_floatx80(0xbfff, 0x8000000000000000ULL),
> ^
We've had the make_floatx80_init() macro for this purpose since commit
3bf7e40ab9 ("softfloat: fix for C99", 2012-03-17), so let's use that
macro again.
Fixes: eca30647fc ("target/i386: reimplement f2xm1 using floatx80 operations")
Fixes: ff57bb7b63 ("target/i386: reimplement fpatan using floatx80 operations")
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Joseph Myers <joseph@codesourcery.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Link: https://lists.gnu.org/archive/html/qemu-devel/2017-08/msg06566.html
Link: https://lists.gnu.org/archive/html/qemu-devel/2020-07/msg04714.html
Message-Id: <20200716144251.23004-1-lersek@redhat.com>
Message-Id: <20200724064509.331-8-alex.bennee@linaro.org>
This will be used in a future patch. For POSIX systems _SC_PHYS_PAGES
isn't standardised but at least appears in the man pages for
Open/FreeBSD. The result is advisory so any users of it shouldn't just
fail if we can't work it out.
The win32 stub currently returns 0 until someone with a Windows system
can develop and test a patch.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Cc: BALATON Zoltan <balaton@eik.bme.hu>
Cc: Christian Ehrhardt <christian.ehrhardt@canonical.com>
Message-Id: <20200724064509.331-5-alex.bennee@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEuBi5yt+QicLVzsZrda1lgCoLQhEFAl8beSIACgkQda1lgCoL
QhEYJwf/X+mekAhZ1os77TvEbA+YVoPrXnPEu1UTWVHBWkmzQisk2eRMj1LlA2+T
a+kEpbw+a1oc3GSWBHXJIVWuFOcA+GEDFerpQypSowAVJHPKam3xPBraP/R+bjXq
e3D7WDMfjOE2sZ2Aj1I9sBZnKOI5yg9GcQ2PjB6btAB2eKJjns2myvhWiA5XEa/H
l+eKtej3u8CvQ51vIrTxV/pvEqhPl1b4kvjj+40/COSMIcQ5OWdVk3de1ty9I8dP
UjeaPRVXsJqYo/ZsUZS/uAdPIn8Ih77OtJRAEGSNe/KgttPQ/EG94mhiEws8xl+b
JiV5HehRW0LB+f6eVGrQ0SbH7TCkCA==
=/17e
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanberger/tags/pull-tpm-2020-07-24-1' into staging
Merge tpm 2020/07/24 v1
# gpg: Signature made Sat 25 Jul 2020 01:13:22 BST
# gpg: using RSA key B818B9CADF9089C2D5CEC66B75AD65802A0B4211
# gpg: Good signature from "Stefan Berger <stefanb@linux.vnet.ibm.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B818 B9CA DF90 89C2 D5CE C66B 75AD 6580 2A0B 4211
* remotes/stefanberger/tags/pull-tpm-2020-07-24-1:
tpm_emulator: Report an error if chardev is missing
tpm: Improve help on TPM types when none are available
Revert "tpm: Clean up error reporting in tpm_init_tpmdev()"
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This reverts commit d10e05f15d.
We report some -tpmdev failures, but then continue as if all was fine.
Reproducer:
$ qemu-system-x86_64 -nodefaults -S -display none -monitor stdio -chardev null,id=tpm0 -tpmdev emulator,id=tpm0,chardev=chrtpm -device tpm-tis,tpmdev=tpm0
qemu-system-x86_64: -tpmdev emulator,id=tpm0,chardev=chrtpm: tpm-emulator: tpm chardev 'chrtpm' not found.
qemu-system-x86_64: -tpmdev emulator,id=tpm0,chardev=chrtpm: tpm-emulator: Could not cleanly shutdown the TPM: No such file or directory
QEMU 5.0.90 monitor - type 'help' for more information
(qemu) qemu-system-x86_64: -device tpm-tis,tpmdev=tpm0: Property 'tpm-tis.tpmdev' can't find value 'tpm0'
$ echo $?
1
This is a regression caused by commit d10e05f15d "tpm: Clean up error
reporting in tpm_init_tpmdev()". It's incomplete: be->create(opts)
continues to use error_report(), and we don't set an error when it
fails.
I figure converting the create() methods to Error would make some
sense, but I'm not sure it's worth the effort right now. Revert the
broken commit instead, and add a comment to tpm_init_tpmdev().
Straightforward conflict in tpm.c resolved.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
error_propagate_prepend() "behaves like error_prepend()", and
error_prepend() uses "formatting @fmt, ... like printf()".
error_prepend() checks its format string argument, but
error_propagate_prepend() does not. Fix by addint the format
attribute to error_propagate_prepend() and error_vprepend().
This would have caught the bug fixed in the previous commit.
Missed in commit 4b5766488f "error: Fix use of error_prepend() with
&error_fatal, &error_abort".
Inspired-by: Stefan Weil <sw@weilnetz.de>
Suggested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200723171205.14949-1-philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The main fix is the correction of the goldfish RTC time. On top of that
some small fixes to the recently added vector extensions have been added
(including an assert that fixed a coverity report). There is a change in
the SiFive E debug memory size to match hardware. Finally there is a fix
for PMP accesses.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAl8YbM8ACgkQIeENKd+X
cFRusgf+NpstlmK/+35DimtJ9oYV2H+NSE7D9HDEdgm2PszYNDjEiWRMBCl1B2JS
3vTutR198USdcJtdXFrFooaxZaMNf0FQJ7p82BUnNOlUNy7vyFlsRQX687KWJh3+
F0t9MsaBVY3G1UiY6vke2vPdcHNG0cAPUwEWjKIU7E7nBmbvNnZZyXxYGC7yjCBI
GQ1TKqso9wKtvAyc6cNGPcsUUM8P+LI5H+UzQR8A1LZ5bohKIQW+xrdJe6HqGMs1
3xZ4tQS2AG5XaaKz74/AdTJSTf80plG2jDomI9fBoNjqRnyPRAlwgzO88Hc24Bcm
RLzL51UaQv+EddxspAW9gH9FHJRvfA==
=6MUF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20200722-1' into staging
This PR contains a few RISC-V fixes.
The main fix is the correction of the goldfish RTC time. On top of that
some small fixes to the recently added vector extensions have been added
(including an assert that fixed a coverity report). There is a change in
the SiFive E debug memory size to match hardware. Finally there is a fix
for PMP accesses.
# gpg: Signature made Wed 22 Jul 2020 17:43:59 BST
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20200722-1:
target/riscv: Fix the range of pmpcfg of CSR funcion table
hw/riscv: sifive_e: Correct debug block size
target/riscv: fix vector index load/store constraints
target/riscv: Quiet Coverity complains about vamo*
goldfish_rtc: Fix non-atomic read behaviour of TIME_LOW/TIME_HIGH
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix bug in ACPI which were tripping up guests.
Fix a use-after-free with hotplug of virtio devices.
Block ability to create legacy devices which shouldn't have been
there in the first place.
Fix migration error handling with balloon.
Drop some dead code in virtio.
vtd emulation fixup.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl8YK/4PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpCE4H/1+15xjUiKD0sxnvPdKezbDhtAW0YPY/cHC0
KJRWFDbK/+cl9ZkJQBqUXASV3KWnjSKjQrVph6vtg8huqhhDsnha1JGgamhOa9tC
7rH8RkMA6nUF/su8xnkNyNBfG2lHk6ETyKvvTtuLHzjbkzWd6OYtaQAQJTYI6TVB
aY+MCIT7xfucsL6JaHA8BTccOOjz7pxc6dL4NsQCR3cZkwTtB9JOE5UwgM3IyNP/
DcbFyVUDkXYtlpKU/xO+ZICbxCNsZmHzpnV8KJ07vyJdAhL1hRAayMkNG4xLzW0n
f/ZMlJna5jDP3fRqgVvu8XbY3TcCx1XOBD9ebH5E6hvhWnp8oHI=
=SJjI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi,virtio,pc: bugfixes
Fix bug in ACPI which were tripping up guests.
Fix a use-after-free with hotplug of virtio devices.
Block ability to create legacy devices which shouldn't have been
there in the first place.
Fix migration error handling with balloon.
Drop some dead code in virtio.
vtd emulation fixup.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 22 Jul 2020 13:07:26 BST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
virtio-pci: Changed vdev to proxy for VirtIO PCI BAR callbacks.
intel_iommu: Use correct shift for 256 bits qi descriptor
virtio: verify that legacy support is not accidentally on
virtio: list legacy-capable devices
virtio-balloon: Replace free page hinting references to 'report' with 'hint'
virtio-balloon: Add locking to prevent possible race when starting hinting
virtio-balloon: Prevent guest from starting a report when we didn't request one
virtio: Drop broken and superfluous object_property_set_link()
acpi: accept byte and word access to core ACPI registers
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The specification says:
0x00 TIME_LOW R: Get current time, then return low-order 32-bits.
0x04 TIME_HIGH R: Return high 32-bits from previous TIME_LOW read.
...
To read the value, the kernel must perform an IO_READ(TIME_LOW),
which returns an unsigned 32-bit value, before an IO_READ(TIME_HIGH),
which returns a signed 32-bit value, corresponding to the higher half
of the full value.
However, we were just returning the current time for both. If the guest
is unlucky enough to read TIME_LOW and TIME_HIGH either side of an
overflow of the lower half, it will see time be in the future, before
jumping backwards on the next read, and Linux currently relies on the
atomicity guaranteed by the spec so is affected by this. Fix this
violation of the spec by caching the correct value for TIME_HIGH
whenever TIME_LOW is read, and returning that value for any TIME_HIGH
read.
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200718004934.83174-1-jrtc27@jrtc27.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Several types of virtio devices had already been around before the
virtio standard was specified. These devices support virtio in legacy
(and transitional) mode.
Devices that have been added in the virtio standard are considered
non-transitional (i.e. with no support for legacy virtio).
Provide a helper function so virtio transports can figure that out
easily.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200707105446.677966-2-cohuck@redhat.com>
Cc: qemu-stable@nongnu.org
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Recently a feature named Free Page Reporting was added to the virtio
balloon. In order to avoid any confusion we should drop the use of the word
'report' when referring to Free Page Hinting. So what this patch does is go
through and replace all instances of 'report' with 'hint" when we are
referring to free page hinting.
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Message-Id: <20200720175128.21935.93927.stgit@localhost.localdomain>
Cc: qemu-stable@nongnu.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commits b6d7e9b66f..a43770df5d simplified the error propagation.
Similarly to commit 6fd5bef10b "qom: Make functions taking Error**
return bool, not void", let fw_cfg_add_from_generator() return a
boolean value, not void.
This allow to simplify parse_fw_cfg() and fixes the error handling
issue reported by Coverity (CID 1430396):
In parse_fw_cfg():
Variable assigned once to a constant guards dead code.
Local variable local_err is assigned only once, to a constant
value, making it effectively constant throughout its scope.
If this is not the intent, examine the logic to see if there
is a missing assignment that would make local_err not remain
constant.
It's the call of fw_cfg_add_from_generator():
Error *local_err = NULL;
fw_cfg_add_from_generator(fw_cfg, name, gen_id, errp);
if (local_err) {
error_propagate(errp, local_err);
return -1;
}
return 0;
If it fails, parse_fw_cfg() sets an error and returns 0, which is
wrong. Harmless, because the only caller passes &error_fatal.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Fixes: Coverity CID 1430396: 'Constant' variable guards dead code (DEADCODE)
Fixes: 6552d87c48 ("softmmu/vl: Let -fw_cfg option take a 'gen_id' argument")
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200721131911.27380-3-philmd@redhat.com>
Document FWCfgDataGeneratorClass::get_data() return NULL
on error, and non-NULL on success. This allow us to simplify
fw_cfg_add_from_generator(). Since we don't need a local
variable to propagate the error, we can remove the ERRP_GUARD()
macro.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200721131911.27380-2-philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200714160202.3121879-5-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
object_get_canonical_path_component() returns a malloced copy of a
property name on success, null on failure.
19 of its 25 callers immediately free the returned copy.
Change object_get_canonical_path_component() to return the property
name directly. Since modifying the name would be wrong, adjust the
return type to const char *.
Drop the free from the 19 callers become simpler, add the g_strdup()
to the other six.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200714160202.3121879-4-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Eric Auger