Simply moving the non-stub helper_v7m_mrs/msr outside of
!CONFIG_USER_ONLY is not an option, because of all of the
other system-mode helpers that are called.
But we can split out a few subroutines to handle the few
EL0 accessible registers without duplicating code.
Reported-by: Christophe Lyon <christophe.lyon@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191118194916.3670-1-richard.henderson@linaro.org
[PMM: deleted now-redundant comment; added a default case
to switch in v7m_msr helper]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Armv8-A removes UNPREDICTABLE for R13 for these cases.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191117090621.32425-3-richard.henderson@linaro.org
[PMM: changed ENABLE_ARCH_8 checks to check a new bool 'v8a',
since these cases are still UNPREDICTABLE for v8M]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There was too much cut and paste between ldrexd and strexd,
as ldrexd does prohibit two output registers the same.
Fixes: af28822899
Reported-by: Michael Goffioul <michael.goffioul@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191117090621.32425-2-richard.henderson@linaro.org
Reviewed-by: Robert Foley <robert.foley@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Coverity reports, in sve_zcr_get_valid_len,
"Subtract operation overflows on operands
arm_cpu_vq_map_next_smaller(cpu, start_vq + 1U) and 1U"
First, the aarch32 stub version of arm_cpu_vq_map_next_smaller,
returning 0, does exactly what Coverity reports. Remove it.
Second, the aarch64 version of arm_cpu_vq_map_next_smaller has
a set of asserts, but they don't cover the case in question.
Further, there is a fair amount of extra arithmetic needed to
convert from the 0-based zcr register, to the 1-base vq form,
to the 0-based bitmap, and back again. This can be simplified
by leaving the value in the 0-based form.
Finally, use test_bit to simplify the common case, where the
length in the zcr registers is in fact a supported length.
Reported-by: Coverity (CID 1407217)
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20191118091414.19440-1-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Attempting to migrate a VM using the microvm machine class results in the source
QEMU aborting with the following message/backtrace:
target/i386/machine.c:955:tsc_khz_needed: Object 0x555556608fa0 is not an
instance of type generic-pc-machine
abort()
object_class_dynamic_cast_assert()
vmstate_save_state_v()
vmstate_save_state()
vmstate_save()
qemu_savevm_state_complete_precopy()
migration_thread()
migration_thread()
migration_thread()
qemu_thread_start()
start_thread()
clone()
The access to the machine class returned by MACHINE_GET_CLASS() in
tsc_khz_needed() is crashing as it is trying to dereference a different
type of machine class object (TYPE_PC_MACHINE) to that of this microVM.
This can be resolved by extending the changes in the following commit
f0bb276bf8 ("hw/i386: split PCMachineState deriving X86MachineState from it")
and moving the save_tsc_khz field in PCMachineClass to X86MachineClass.
Fixes: f0bb276bf8 ("hw/i386: split PCMachineState deriving X86MachineState from it")
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-Id: <1574075605-25215-1-git-send-email-liam.merwick@oracle.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
TSX Async Abort (TAA) is a side channel attack on internal buffers in
some Intel processors similar to Microachitectural Data Sampling (MDS).
Some future Intel processors will use the ARCH_CAP_TAA_NO bit in the
IA32_ARCH_CAPABILITIES MSR to report that they are not vulnerable to
TAA. Make this bit available to guests.
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We have to set the default model of all machine classes, not just for
the active one. Otherwise, "query-machines" will indicate the wrong
CPU model (e.g. "power9_v2.0-powerpc64-cpu" instead of
"host-powerpc64-cpu") as "default-cpu-type".
s390x already fixed this in de60a92e "s390x/kvm: Set default cpu model for
all machine classes". This patch applies a similar fix for the pseries-*
machine types on ppc64.
Doing a
{"execute":"query-machines"}
under KVM now results in
{
"hotpluggable-cpus": true,
"name": "pseries-4.2",
"numa-mem-supported": true,
"default-cpu-type": "host-powerpc64-cpu",
"is-default": true,
"cpu-max": 1024,
"deprecated": false,
"alias": "pseries"
},
{
"hotpluggable-cpus": true,
"name": "pseries-4.1",
"numa-mem-supported": true,
"default-cpu-type": "host-powerpc64-cpu",
"cpu-max": 1024,
"deprecated": false
},
...
Libvirt probes all machines via "-machine none,accel=kvm:tcg" and will
currently see the wrong CPU model under KVM.
Reported-by: Jiři Denemark <jdenemar@redhat.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Jiri Denemark <jdenemar@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Instead of relying on atomics to access the MIP register let's update
our helper function to instead just lock the IO mutex thread before
writing. This follows the same concept as used in PPC for handling
interrupts
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Plug temp leak around eval_cond_jmp().
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Plug temp leaks with delay slot setup.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Simplify endian reversion of address also plugging TCG temp
leaks for loads/stores.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
rt==15 is a special case when reading the flags: it means the
destination is APSR. This patch avoids rejecting
vmrs apsr_nzcv, fpscr
as illegal instruction.
Cc: qemu-stable@nongnu.org
Signed-off-by: Christophe Lyon <christophe.lyon@linaro.org>
Message-id: 20191025095711.10853-1-christophe.lyon@linaro.org
[PMM: updated the comment]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow cpu 'host' to enable SVE when it's available, unless the
user chooses to disable it with the added 'sve=off' cpu property.
Also give the user the ability to select vector lengths with the
sve<N> properties. We don't adopt 'max' cpu's other sve property,
sve-max-vq, because that property is difficult to use with KVM.
That property assumes all vector lengths in the range from 1 up
to and including the specified maximum length are supported, but
there may be optional lengths not supported by the host in that
range. With KVM one must be more specific when enabling vector
lengths.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Message-id: 20191031142734.8590-10-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Extend the SVE vq map initialization and validation with KVM's
supported vector lengths when KVM is enabled. In order to determine
and select supported lengths we add two new KVM functions for getting
and setting the KVM_REG_ARM64_SVE_VLS pseudo-register.
This patch has been co-authored with Richard Henderson, who reworked
the target/arm/cpu64.c changes in order to push all the validation and
auto-enabling/disabling steps into the finalizer, resulting in a nice
LOC reduction.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Message-id: 20191031142734.8590-9-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
kvm_arm_create_scratch_host_vcpu() takes a struct kvm_vcpu_init
parameter. Rather than just using it as an output parameter to
pass back the preferred target, use it also as an input parameter,
allowing a caller to pass a selected target if they wish and to
also pass cpu features. If the caller doesn't want to select a
target they can pass -1 for the target which indicates they want
to use the preferred target and have it passed back like before.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Reviewed-by: Beata Michalska <beata.michalska@linaro.org>
Message-id: 20191031142734.8590-8-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable SVE in the KVM guest when the 'max' cpu type is configured
and KVM supports it. KVM SVE requires use of the new finalize
vcpu ioctl, so we add that now too. For starters SVE can only be
turned on or off, getting all vector lengths the host CPU supports
when on. We'll add the other SVE CPU properties in later patches.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Reviewed-by: Beata Michalska <beata.michalska@linaro.org>
Message-id: 20191031142734.8590-7-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These are the SVE equivalents to kvm_arch_get/put_fpsimd. Note, the
swabbing is different than it is for fpsmid because the vector format
is a little-endian stream of words.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Message-id: 20191031142734.8590-6-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce cpu properties to give fine control over SVE vector lengths.
We introduce a property for each valid length up to the current
maximum supported, which is 2048-bits. The properties are named, e.g.
sve128, sve256, sve384, sve512, ..., where the number is the number of
bits. See the updates to docs/arm-cpu-features.rst for a description
of the semantics and for example uses.
Note, as sve-max-vq is still present and we'd like to be able to
support qmp_query_cpu_model_expansion with guests launched with e.g.
-cpu max,sve-max-vq=8 on their command lines, then we do allow
sve-max-vq and sve<N> properties to be provided at the same time, but
this is not recommended, and is why sve-max-vq is not mentioned in the
document. If sve-max-vq is provided then it enables all lengths smaller
than and including the max and disables all lengths larger. It also has
the side-effect that no larger lengths may be enabled and that the max
itself cannot be disabled. Smaller non-power-of-two lengths may,
however, be disabled, e.g. -cpu max,sve-max-vq=4,sve384=off provides a
guest the vector lengths 128, 256, and 512 bits.
This patch has been co-authored with Richard Henderson, who reworked
the target/arm/cpu64.c changes in order to push all the validation and
auto-enabling/disabling steps into the finalizer, resulting in a nice
LOC reduction.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Reviewed-by: Beata Michalska <beata.michalska@linaro.org>
Message-id: 20191031142734.8590-5-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since 97a28b0eea ("target/arm: Allow VFP and Neon to be disabled via
a CPU property") we can disable the 'max' cpu model's VFP and neon
features, but there's no way to disable SVE. Add the 'sve=on|off'
property to give it that flexibility. We also rename
cpu_max_get/set_sve_vq to cpu_max_get/set_sve_max_vq in order for them
to follow the typical *_get/set_<property-name> pattern.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Reviewed-by: Beata Michalska <beata.michalska@linaro.org>
Message-id: 20191031142734.8590-4-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for the query-cpu-model-expansion QMP command to Arm. We
do this selectively, only exposing CPU properties which represent
optional CPU features which the user may want to enable/disable.
Additionally we restrict the list of queryable cpu models to 'max',
'host', or the current type when KVM is in use. And, finally, we only
implement expansion type 'full', as Arm does not yet have a "base"
CPU type. More details and example queries are described in a new
document (docs/arm-cpu-features.rst).
Note, certainly more features may be added to the list of advertised
features, e.g. 'vfp' and 'neon'. The only requirement is that we can
detect invalid configurations and emit failures at QMP query time.
For 'vfp' and 'neon' this will require some refactoring to share a
validation function between the QMP query and the CPU realize
functions.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Beata Michalska <beata.michalska@linaro.org>
Message-id: 20191031142734.8590-2-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- use --enable-plugins @ configure
- low impact introspection (-plugin empty.so to measure overhead)
- plugins cannot alter guest state
- example plugins included in source tree (tests/plugins)
- -d plugin to enable plugin output in logs
- check-tcg runs extra tests when plugins enabled
- documentation in docs/devel/plugins.rst
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAl23BZMACgkQ+9DbCVqe
KkRPegf/QHygZ4ER2jOaWEookxiOEcik+dzQKVGNqLNXeMLvo5fGjGVpFoFxSgfv
ZvCAL4xbW44zsYlVfh59tfn4Tu9qK7s7/qM3WXpHsmuvEuhoWef0Lt2jSe+D46Rs
KeG/aX+rHLUR8rr9eCgE+1/MQmxPUj3VUonkUpNkk2ebBbSNoLSOudB4DD9Vcyl7
Pya1kPvA6W9bwI20ZSWihE7flg13o62Pp+LgAFLrsfxXOxOMkPrU8Pp+B0Dvr+hL
5Oh0clZLhiRi75x+KVGZ90TVsoftdjYoOWGMOudS/+NNmqKT1NTLm0K1WJYyRMQ1
V0ne4/OcGNq7x8gcOx/xs09ADu5/VA==
=UXR/
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-tcg-plugins-281019-4' into staging
TCG Plugins initial implementation
- use --enable-plugins @ configure
- low impact introspection (-plugin empty.so to measure overhead)
- plugins cannot alter guest state
- example plugins included in source tree (tests/plugins)
- -d plugin to enable plugin output in logs
- check-tcg runs extra tests when plugins enabled
- documentation in docs/devel/plugins.rst
# gpg: Signature made Mon 28 Oct 2019 15:13:23 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-tcg-plugins-281019-4: (57 commits)
travis.yml: enable linux-gcc-debug-tcg cache
MAINTAINERS: add me for the TCG plugins code
scripts/checkpatch.pl: don't complain about (foo, /* empty */)
.travis.yml: add --enable-plugins tests
include/exec: wrap cpu_ldst.h in CONFIG_TCG
accel/stubs: reduce headers from tcg-stub
tests/plugin: add hotpages to analyse memory access patterns
tests/plugin: add instruction execution breakdown
tests/plugin: add a hotblocks plugin
tests/tcg: enable plugin testing
tests/tcg: drop test-i386-fprem from TESTS when not SLOW
tests/tcg: move "virtual" tests to EXTRA_TESTS
tests/tcg: set QEMU_OPTS for all cris runs
tests/tcg/Makefile.target: fix path to config-host.mak
tests/plugin: add sample plugins
linux-user: support -plugin option
vl: support -plugin option
plugin: add qemu_plugin_outs helper
plugin: add qemu_plugin_insn_disas helper
plugin: expand the plugin_init function to include an info block
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
riscv_cpu_tlb_fill() uses the `size` parameter to check PMP violation
using pmp_hart_has_privs().
However, if the size is unknown (=0), the ending address will be
`addr - 1` as it is `addr + size - 1` in `pmp_hart_has_privs()`.
This always causes a false PMP violation on the starting address of the
range, as `addr - 1` is not in the range.
In order to fix, we just assume that all bytes from addr to the end of
the page will be accessed if the size is unknown.
Signed-off-by: Dayeol Lee <dayeol@berkeley.edu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
There is a small wrinkle with the gUSA instruction. The translator
effectively treats a (known) gUSA sequence as a single instruction.
For the purposes of the plugin we end up with a long multi-instruction
qemu_plugin_insn.
If the known sequence isn't detected we shall never run this
translation anyway.
Signed-off-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Now the arm_ld*_code functions are only used at translate time we can
just pass down to translator_ld functions.
Signed-off-by: Emilio G. Cota <cota@braap.org>
[AJB: convert from plugin_insn_append to translator_ld]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
We document this in docs/devel/load-stores.rst so lets follow it. The
32 bit and 64 bit access functions have historically not included the
sign so we leave those as is. We also introduce some signed helpers
which are used for loading immediate values in the translator.
Fixes: 282dffc8
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20191021150910.23216-1-alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Currently only PRV_U, PRV_S and PRV_M are supported, so this patch ensures that
the privilege mode is set to one of them. Once support for the H-extension is
added, this code will also need to properly update the virtualization status
when switching between VU/VS-modes and M-mode.
Signed-off-by: Jonathan Behrens <jonathan@fintelia.io>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch enables a debugger to read the current privilege level via a virtual
"priv" register. When compiled with CONFIG_USER_ONLY the register is still
visible but always reports the value zero.
Signed-off-by: Jonathan Behrens <jonathan@fintelia.io>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
If the number of registers reported to the gdbstub code does not match the
number in the associated XML file, then the register numbers used by the stub
may get out of sync with a remote GDB instance.
Signed-off-by: Jonathan Behrens <jonathan@fintelia.io>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The CPU loop tagged all the queued signals as QEMU_SI_KILL while it was
filling the `_sigfault` part of `siginfo`: this caused QEMU to copy the
wrong fields over to the userspace program.
Make sure the fault address recorded by the MMU is is stored in the CPU
environment structure.
In case of memory faults store the exception address into `siginfo`.
Signed-off-by: Giuseppe Musacchio <thatlemon@gmail.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This converts our port over from cpu_do_unassigned_access to
cpu_do_transaction_failed, as cpu_do_unassigned_access has been
deprecated.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
We directly access physical memory while walking the page tables on
RISC-V, but while doing so we were using cpu_ld*() which does not report
bus errors. This patch converts the page table walker over to use
address_space_ld*(), which allows bus errors to be detected.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
If we are in debugger mode, skip the CSR privilege level checking
so that we can read/write all CSRs. Otherwise we get:
(gdb) p/x $mtvec
Could not fetch register "mtvec"; remote failure reply 'E14'
when the hart is currently in S-mode.
Reported-by: Zong Li <zong.li@sifive.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
We document this in docs/devel/load-stores.rst so lets follow it. The
32 bit and 64 bit access functions have historically not included the
sign so we leave those as is. We also introduce some signed helpers
which are used for loading immediate values in the translator.
Fixes: 282dffc8
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20191021150910.23216-1-alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Change the handling of port F0h writes and FPU exceptions to implement IGNNE.
The implementation mixes a bit what the chipset and processor do in real
hardware, but the effect is the same as what happens with actual FERR#
and IGNNE# pins: writing to port F0h asserts IGNNE# in addition to lowering
FP_IRQ; while clearing the SE bit in the FPU status word deasserts IGNNE#.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move it out of pc.c since it is strictly tied to TCG. This is
almost exclusively code movement, the next patch will implement
IGNNE.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are three page size in qemu:
real host page size
host page size
target page size
All of them have dedicate variable to represent. For the last two, we
use the same form in the whole qemu project, while for the first one we
use two forms: qemu_real_host_page_size and getpagesize().
qemu_real_host_page_size is defined to be a replacement of
getpagesize(), so let it serve the role.
[Note] Not fully tested for some arch or device.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20191013021145.16011-3-richardw.yang@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove unnecessary argument and provide separate function for each
instruction.
Signed-off-by: Filip Bozuta <Filip.Bozuta@rt-rk.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1571837825-24438-3-git-send-email-Filip.Bozuta@rt-rk.com>
Remove unnecessary argument and provide separate function for each
instruction.
Signed-off-by: Filip Bozuta <Filip.Bozuta@rt-rk.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1571837825-24438-2-git-send-email-Filip.Bozuta@rt-rk.com>
This makes searches for instances of opcode usages easier.
Reviewed-by: Aleksandar Rikalo <aleksandar.rikalo@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1571826227-10583-15-git-send-email-aleksandar.markovic@rt-rk.com>
Mostly fix errors and warnings reported by 'checkpatch.pl -f'.
Reviewed-by: Aleksandar Rikalo <aleksandar.rikalo@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1571826227-10583-3-git-send-email-aleksandar.markovic@rt-rk.com>
Mostly fix errors and warnings reported by 'checkpatch.pl -f'.
Cc: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Aleksandar Rikalo <aleksandar.rikalo@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1571826227-10583-2-git-send-email-aleksandar.markovic@rt-rk.com>
This is the payoff.
From perf record -g data of ubuntu 18 boot and shutdown:
BEFORE:
- 23.02% 2.82% qemu-system-aar [.] helper_lookup_tb_ptr
- 20.22% helper_lookup_tb_ptr
+ 10.05% tb_htable_lookup
- 9.13% cpu_get_tb_cpu_state
3.20% aa64_va_parameters_both
0.55% fp_exception_el
- 11.66% 4.74% qemu-system-aar [.] cpu_get_tb_cpu_state
- 6.96% cpu_get_tb_cpu_state
3.63% aa64_va_parameters_both
0.60% fp_exception_el
0.53% sve_exception_el
AFTER:
- 16.40% 3.40% qemu-system-aar [.] helper_lookup_tb_ptr
- 13.03% helper_lookup_tb_ptr
+ 11.19% tb_htable_lookup
0.55% cpu_get_tb_cpu_state
0.98% 0.71% qemu-system-aar [.] cpu_get_tb_cpu_state
0.87% 0.24% qemu-system-aar [.] rebuild_hflags_a64
Before, helper_lookup_tb_ptr is the second hottest function in the
application, consuming almost a quarter of the runtime. Within the
entire execution, cpu_get_tb_cpu_state consumes about 12%.
After, helper_lookup_tb_ptr has dropped to the fourth hottest function,
with consumption dropping to a sixth of the runtime. Within the
entire execution, cpu_get_tb_cpu_state has dropped below 1%, and the
supporting function to rebuild hflags also consumes about 1%.
Assertions are retained for --enable-debug-tcg.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-25-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Continue setting, but not relying upon, env->hflags.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-21-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Continue setting, but not relying upon, env->hflags.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-20-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Continue setting, but not relying upon, env->hflags.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-19-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Continue setting, but not relying upon, env->hflags.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-18-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Begin setting, but not relying upon, env->hflags.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-17-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This functions are given the mode and el state of the cpu
and writes the computed value to env->hflags.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-16-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
By performing this store early, we avoid having to save and restore
the register holding the address around any function calls.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-15-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This function assumes nothing about the current state of the cpu,
and writes the computed value to env->hflags.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-13-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are 3 conditions that each enable this flag. M-profile always
enables; A-profile with EL1 as AA64 always enables. Both of these
conditions can easily be cached. The final condition relies on the
FPEXC register which we are not prepared to cache.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-12-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Hoist the variable load for PSTATE into the existing test vs is_a64.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-11-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We do not need to compute any of these values for M-profile.
Further, XSCALE_CPAR overlaps VECSTRIDE so obviously the two
sets must be mutually exclusive.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-10-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a function to compute the values of the TBFLAG_ANY bits
that will be cached, and are used by A-profile.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-9-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently a trivial wrapper for rebuild_hflags_common_32.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-8-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Hoist the computation of some TBFLAG_A32 bits that only apply to
M-profile under a single test for ARM_FEATURE_M.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-7-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a function to compute the values of the TBFLAG_A32 bits
that will be cached, and are used by M-profile.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-6-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Set TBFLAG_ANY.BE_DATA in rebuild_hflags_common_32 and
rebuild_hflags_a64 instead of rebuild_hflags_common, where we do
not need to re-test is_a64() nor re-compute the various inputs.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-5-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a function to compute the values of the TBFLAG_A32 bits
that will be cached, and are used by all profiles.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a function to compute the values of the TBFLAG_A64 bits
that will be cached. For now, the env->hflags variable is not
used, and the results are fed back to cpu_get_tb_cpu_state.
Note that not all BTI related flags are cached, so we have to
test the BTI feature twice -- once for those bits moved out to
rebuild_hflags_a64 and once for those bits that remain in
cpu_get_tb_cpu_state.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a function to compute the values of the TBFLAG_ANY bits
that will be cached. For now, the env->hflags variable is not
used, and the results are fed back to cpu_get_tb_cpu_state.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Last pull request before soft freeze.
* Lots of fixes and cleanups for spapr interrupt controllers
* More SLOF updates to fix problems with full FDT rendering at CAS
time (alas, more yet are to come)
* A few other assorted changes
This isn't quite as well tested as I usually try to do before a pull
request. But I've been sick and running into some other difficulties,
and wanted to get this sent out before heading towards KVM forum.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEdfRlhq5hpmzETofcbDjKyiDZs5IFAl2xXWcACgkQbDjKyiDZ
s5Jy/BAAsSo514vGCjdszXcRH3nFeODKJadlSsUX+32JFP1yJS9ooxkcmIN7o9Wp
3VCkMHQPVV9jjIvvShWOSGfDDO3o8fTEucOIX/Nn9wfq+NiY+EJst0v+8OT48CSX
LEXiy9Wghs9pZMLCUZ3rlLPBiU/Lhzf+KTCoUdc40tfoZMMz1lp/Uy8IdIYTYwLl
/z++r4X8FOsXsDDsFopWffVdVBLJz6Var6NgBa8ISk2gGnUOAKsrTE3bD9L6n4PR
YYbMSkv+SbvXg4gm53jUb9cQgpBqQpWHUYBIbKia/16EzbIkkZjFE2jGQMP5c72h
ZOml7ZQtQVWIEEZwKPN67S8bKiVbEfayxHYViejn/uUqv3AwW0wi7FlBVv37YNJ4
TxPvLBu+0DaFbk5y6/XHyL6XomG1/oH6qXOM2JhIWON7HI3rRWoMQbZ6QVJ1Gwk2
uwrvOOL5kVZySotOw5bDkTXYp/Nm1JE4QwOXFPkXzaekcZhRlEqqrkBddhKtF80p
1e5hGp5RgoILIe8uHJQ7decUMk889J7Qdtakv6BWvOci4dbIiZEp/smFlzgTcPnW
DQJONP/awnoAOS3v0bItf59DROvkZ5xyv8yQZFP3qThSOfZl4e95WNRbtR3vtjU4
Bl4Pdte15URKy5nM0XnnLg9mzl2xufdwEsu76lQMuYpe6nCI2h0=
=FRHF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.2-20191024' into staging
ppc patch queue 2019-10-24
Last pull request before soft freeze.
* Lots of fixes and cleanups for spapr interrupt controllers
* More SLOF updates to fix problems with full FDT rendering at CAS
time (alas, more yet are to come)
* A few other assorted changes
This isn't quite as well tested as I usually try to do before a pull
request. But I've been sick and running into some other difficulties,
and wanted to get this sent out before heading towards KVM forum.
# gpg: Signature made Thu 24 Oct 2019 09:14:31 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.2-20191024: (28 commits)
spapr/xive: Set the OS CAM line at reset
ppc/pnv: Fix naming of routines realizing the CPUs
ppc: Reset the interrupt presenter from the CPU reset handler
ppc/pnv: Add a PnvChip pointer to PnvCore
ppc/pnv: Introduce a PnvCore reset handler
spapr_cpu_core: Implement DeviceClass::reset
spapr: move CPU reset after presenter creation
spapr: Don't request to unplug the same core twice
pseries: Update SLOF firmware image
spapr: Move SpaprIrq::nr_xirqs to SpaprMachineClass
spapr: Remove SpaprIrq::nr_msis
spapr, xics, xive: Move SpaprIrq::post_load hook to backends
spapr, xics, xive: Move SpaprIrq::reset hook logic into activate/deactivate
spapr: Remove SpaprIrq::init_kvm hook
spapr, xics, xive: Match signatures for XICS and XIVE KVM connect routines
spapr, xics, xive: Move dt_populate from SpaprIrq to SpaprInterruptController
spapr, xics, xive: Move print_info from SpaprIrq to SpaprInterruptController
spapr, xics, xive: Move set_irq from SpaprIrq to SpaprInterruptController
spapr: Formalize notion of active interrupt controller
spapr, xics, xive: Move irq claim and free from SpaprIrq to SpaprInterruptController
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Denverton is the Atom Processor of Intel Harrisonville platform.
For more information:
https://ark.intel.com/content/www/us/en/ark/products/\
codename/63508/denverton.html
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190718073405.28301-1-tao3.xu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
In previous implementation, invocation of TCG shift function could request
shift of TCG variable by 64 bits when variable 'sh' is 0, which is not
supported in TCG (values can be shifted by 0 to 63 bits). This patch fixes
this by using two separate invocation of TCG shift functions, with maximum
shift amount of 32.
Name of variable 'shifted' is changed to 'carry' so variable naming
is similar to old helper implementation.
Variables 'avrA' and 'avrB' are replaced with variable 'avr'.
Fixes: 4e6d0920e7
Reported-by: "Paul A. Clark" <pc@us.ibm.com>
Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Suggested-by: Aleksandar Markovic <aleksandar.markovic@rt-rk.com>
Signed-off-by: Stefan Brankovic <stefan.brankovic@rt-rk.com>
Message-Id: <1570196639-7025-2-git-send-email-stefan.brankovic@rt-rk.com>
Tested-by: Paul A. Clarke <pc@us.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
UMWAIT and TPAUSE instructions use 32bits IA32_UMWAIT_CONTROL at MSR
index E1H to determines the maximum time in TSC-quanta that the processor
can reside in either C0.1 or C0.2.
This patch is to Add support for save/load IA32_UMWAIT_CONTROL MSR in
guest.
Co-developed-by: Jingqi Liu <jingqi.liu@intel.com>
Signed-off-by: Jingqi Liu <jingqi.liu@intel.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20191011074103.30393-3-tao3.xu@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
UMONITOR, UMWAIT and TPAUSE are a set of user wait instructions.
This patch adds support for user wait instructions in KVM. Availability
of the user wait instructions is indicated by the presence of the CPUID
feature flag WAITPKG CPUID.0x07.0x0:ECX[5]. User wait instructions may
be executed at any privilege level, and use IA32_UMWAIT_CONTROL MSR to
set the maximum time.
The patch enable the umonitor, umwait and tpause features in KVM.
Because umwait and tpause can put a (psysical) CPU into a power saving
state, by default we dont't expose it to kvm and enable it only when
guest CPUID has it. And use QEMU command-line "-overcommit cpu-pm=on"
(enable_cpu_pm is enabled), a VM can use UMONITOR, UMWAIT and TPAUSE
instructions. If the instruction causes a delay, the amount of time
delayed is called here the physical delay. The physical delay is first
computed by determining the virtual delay (the time to delay relative to
the VM’s timestamp counter). Otherwise, UMONITOR, UMWAIT and TPAUSE cause
an invalid-opcode exception(#UD).
The release document ref below link:
https://software.intel.com/sites/default/files/\
managed/39/c5/325462-sdm-vol-1-2abcd-3abcd.pdf
Co-developed-by: Jingqi Liu <jingqi.liu@intel.com>
Signed-off-by: Jingqi Liu <jingqi.liu@intel.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20191011074103.30393-2-tao3.xu@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The 32-bit product should be sign-extended, not zero-extended.
Fixes: ea96b37464
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 20190912183058.17947-1-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Hyper-V TLFS specifies this enlightenment as:
"NoNonArchitecturalCoreSharing - Indicates that a virtual processor will never
share a physical core with another virtual processor, except for virtual
processors that are reported as sibling SMT threads. This can be used as an
optimization to avoid the performance overhead of STIBP".
However, STIBP is not the only implication. It was found that Hyper-V on
KVM doesn't pass MD_CLEAR bit to its guests if it doesn't see
NoNonArchitecturalCoreSharing bit.
KVM reports NoNonArchitecturalCoreSharing in KVM_GET_SUPPORTED_HV_CPUID to
indicate that SMT on the host is impossible (not supported of forcefully
disabled).
Implement NoNonArchitecturalCoreSharing support in QEMU as tristate:
'off' - the feature is disabled (default)
'on' - the feature is enabled. This is only safe if vCPUS are properly
pinned and correct topology is exposed. As CPU pinning is done outside
of QEMU the enablement decision will be made on a higher level.
'auto' - copy KVM setting. As during live migration SMT settings on the
source and destination host may differ this requires us to add a migration
blocker.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20191018163908.10246-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Patch logs MCE AO, AR messages injected to guest or taken by QEMU itself.
We print the QEMU address for guest MCEs, helps on hypervisors that have
another source of MCE logging like mce log, and when they go missing.
For example we found these QEMU logs:
September 26th 2019, 17:36:02.309 Droplet-153258224: Guest MCE Memory Error at qemu addr 0x7f8ce14f5000 and guest 3d6f5000 addr of type BUS_MCEERR_AR injected qemu-system-x86_64 amsN ams3nodeNNNN
September 27th 2019, 06:25:03.234 Droplet-153258224: Guest MCE Memory Error at qemu addr 0x7f8ce14f5000 and guest 3d6f5000 addr of type BUS_MCEERR_AR injected qemu-system-x86_64 amsN ams3nodeNNNN
The first log had a corresponding mce log entry, the second didnt (logging
thresholds) we can infer from second entry same PA and mce type.
Signed-off-by: Mario Smarduch <msmarduch@digitalocean.com>
Message-Id: <20191009164459.8209-3-msmarduch@digitalocean.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We have to set the default model of all machine classes, not just for
the active one. Otherwise, "query-machines" will indicate the wrong
CPU model ("qemu-s390x-cpu" instead of "host-s390x-cpu") as
"default-cpu-type".
Doing a
{"execute":"query-machines"}
under KVM now results in
{"return": [
{
"hotpluggable-cpus": true,
"name": "s390-ccw-virtio-4.0",
"numa-mem-supported": false,
"default-cpu-type": "host-s390x-cpu",
"cpu-max": 248,
"deprecated": false},
{
"hotpluggable-cpus": true,
"name": "s390-ccw-virtio-2.7",
"numa-mem-supported": false,
"default-cpu-type": "host-s390x-cpu",
"cpu-max": 248,
"deprecated": false
} ...
Libvirt probes all machines via "-machine none,accel=kvm:tcg" and will
currently see the wrong CPU model under KVM.
Reported-by: Jiri Denemark <jdenemar@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Fixes: b6805e127c ("s390x: use generic cpu_model parsing")
Cc: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191021100515.6978-1-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The numbers are unsigned, the computation is wrong. "Each operand is
treated as an unsigned binary integer".
Let's implement as given in the PoP:
"A subtraction is performed by adding the contents of the second operand
with the bitwise complement of the third operand along with a borrow
indication from the rightmost bit of the fourth operand."
Reuse gen_accc2_i64().
Fixes: bc725e6515 ("s390x/tcg: Implement VECTOR SUBTRACT WITH BORROW COMPUTE BORROW INDICATION")
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191021085715.3797-7-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Testing this, there seems to be something messed up. We are dealing with
unsigned numbers. "Each operand is treated as an unsigned binary integer."
Let's just implement as written in the PoP:
"A subtraction is performed by adding the contents of
the second operand with the bitwise complement of
the third operand along with a borrow indication from
the rightmost bit position of the fourth operand and
the result is placed in the first operand."
We can reuse gen_ac2_i64().
Fixes: 48390a7c27 ("s390x/tcg: Implement VECTOR SUBTRACT WITH BORROW INDICATION")
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191021085715.3797-6-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Looks like my idea of what a "borrow" is was wrong. The PoP says:
"If the resulting subtraction results in a carry out of bit zero, a value
of one is placed in the corresponding element of the first operand;
otherwise, a value of zero is placed in the corresponding element"
As clarified by Richard, all we have to do is invert the result.
Fixes: 1ee2d7ba72 ("s390x/tcg: Implement VECTOR SUBTRACT COMPUTE BORROW INDICATION")
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191021085715.3797-5-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We forgot to propagate the highest bit accross the high doubleword in
two cases (shift >=64).
Fixes: 5f724887e3 ("s390x/tcg: Implement VECTOR SHIFT RIGHT ARITHMETIC")
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191021085715.3797-4-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We missed that we always read a "double-wide even-odd element
pair of the fourth operand". Fix it in all four variants.
Fixes: 1b430aec41 ("s390x/tcg: Implement VECTOR MULTIPLY AND ADD *")
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191021085715.3797-3-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We have to read from odd offsets.
Fixes: 2bf3ee38f1 ("s390x/tcg: Implement VECTOR MULTIPLY *")
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191021085715.3797-2-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
No need to double-check if we have a write.
Found by Coverity (CID: 1406404).
Fixes: 31b5941906 ("target/s390x: Return exception from mmu_translate_real")
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191017121922.18840-1-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Beata Michalska noticed this missing visit_free() while reviewing
arm's implementation of qmp_query_cpu_model_expansion(), which is
modeled off this s390x implementation.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-Id: <20191016145434.7007-1-drjones@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Overlay part of the test_mmuhifi_c3 core has GPL3 copyright headers in
it. Fix that by regenerating test_mmuhifi_c3 core overlay and
re-importing it.
Fixes: d848ea7767 ("target/xtensa: add test_mmuhifi_c3 core")
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Add new version of Snowridge CPU model that removes MPX feature.
MPX support is being phased out by Intel. GCC has dropped it, Linux kernel
and KVM are also going to do that in the future.
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Message-Id: <20191012024748.127135-1-xiaoyao.li@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
KVM has a 80-entry limit at KVM_SET_CPUID2. With the
introduction of CPUID[0x1F], it is now possible to hit this limit
with unusual CPU configurations, e.g.:
$ ./x86_64-softmmu/qemu-system-x86_64 \
-smp 1,dies=2,maxcpus=2 \
-cpu EPYC,check=off,enforce=off \
-machine accel=kvm
qemu-system-x86_64: kvm_init_vcpu failed: Argument list too long
This happens because QEMU adds a lot of all-zeroes CPUID entries
for unused CPUID leaves. In the example above, we end up
creating 48 all-zeroes CPUID entries.
KVM already returns all-zeroes when emulating the CPUID
instruction if an entry is missing, so the all-zeroes entries are
redundant. Skip those entries. This reduces the CPUID table
size by half while keeping CPUID output unchanged.
Reported-by: Yumei Huang <yuhuang@redhat.com>
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1741508
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190822225210.32541-1-ehabkost@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Drop the duplicated definition of cpuid AVX512_VBMI macro and rename
it as CPUID_7_0_ECX_AVX512_VBMI. Rename CPUID_7_0_ECX_VBMI2 as
CPUID_7_0_ECX_AVX512_VBMI2.
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190926021055.6970-3-tao3.xu@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add some comments, clean up comments over 80 chars per line. And there
is an extra line in comment of CPUID_8000_0008_EBX_WBNOINVD, remove
the extra enter and spaces.
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190926021055.6970-2-tao3.xu@intel.com>
[ehabkost: rebase to latest git master]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
SH_EXT_STDOUT_STDERR is a v2.0 semihosting extension: the guest
can open ":tt" with a file mode requesting append access in
order to open stderr, in addition to the existing "open for
read for stdin or write for stdout". Implement this and
report it via the :semihosting-features data.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190916141544.17540-16-peter.maydell@linaro.org
SH_EXT_EXIT_EXTENDED is a v2.0 semihosting extension: it
indicates that the implementation supports the SYS_EXIT_EXTENDED
function. This function allows both A64 and A32/T32 guests to
exit with a specified exit status, unlike the older SYS_EXIT
function which only allowed this for A64 guests. Implement
this extension.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190916141544.17540-15-peter.maydell@linaro.org
Version 2.0 of the semihosting specification added support for
allowing a guest to detect whether the implementation supported
particular features. This works by the guest opening a magic
file ":semihosting-features", which contains a fixed set of
data with some magic numbers followed by a sequence of bytes
with feature flags. The file is expected to behave sensibly
for the various semihosting calls which operate on files
(SYS_FLEN, SYS_SEEK, etc).
Implement this as another kind of guest FD using our function
table dispatch mechanism. Initially we report no extended
features, so we have just one feature flag byte which is zero.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190916141544.17540-14-peter.maydell@linaro.org
Factor out the implementation of SYS_FLEN via the new
function tables.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190916141544.17540-13-peter.maydell@linaro.org
Factor out the implementation of SYS_SEEK via the new function
tables.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190916141544.17540-12-peter.maydell@linaro.org
Factor out the implementation of SYS_ISTTY via the new function
tables.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190916141544.17540-11-peter.maydell@linaro.org
Factor out the implementation of SYS_READ via the
new function tables.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190916141544.17540-10-peter.maydell@linaro.org
Factor out the implementation of SYS_WRITE via the
new function tables.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190916141544.17540-9-peter.maydell@linaro.org
Currently for the semihosting calls which take a file descriptor
(SYS_CLOSE, SYS_WRITE, SYS_READ, SYS_ISTTY, SYS_SEEK, SYS_FLEN)
we have effectively two implementations, one for real host files
and one for when we indirect via the gdbstub. We want to add a
third one to deal with the magic :semihosting-features file.
Instead of having a three-way if statement in each of these
cases, factor out the implementation of the calls to separate
functions which we dispatch to via function pointers selected
via the GuestFDType for the guest fd.
In this commit, we set up the framework for the dispatch,
and convert the SYS_CLOSE call to use it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190916141544.17540-8-peter.maydell@linaro.org
When we are routing semihosting operations through the gdbstub, the
work of sorting out the return value and setting errno if necessary
is done by callback functions which are invoked by the gdbstub code.
Clean up some ifdeffery in those functions by having them call
set_swi_errno() to set the semihosting errno.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190916141544.17540-7-peter.maydell@linaro.org
The semihosting code needs accuss to the linux-user only
TaskState pointer so it can set the semihosting errno per-thread
for linux-user mode. At the moment we do this by having some
ifdefs so that we define a 'ts' local in do_arm_semihosting()
which is either a real TaskState * or just a CPUARMState *,
depending on which mode we're compiling for.
This is awkward if we want to refactor do_arm_semihosting()
into other functions which might need to be passed the TaskState.
Restrict usage of the TaskState local by:
* making set_swi_errno() always take the CPUARMState pointer
and (for the linux-user version) get TaskState from that
* creating a new get_swi_errno() which reads the errno
* having the two semihosting calls which need the TaskState
for other purposes (SYS_GET_CMDLINE and SYS_HEAPINFO)
define a variable with scope restricted to just that code
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190916141544.17540-6-peter.maydell@linaro.org
Currently the Arm semihosting code returns the guest file descriptors
(handles) which are simply the fd values from the host OS or the
remote gdbstub. Part of the semihosting 2.0 specification requires
that we implement special handling of opening a ":semihosting-features"
filename. Guest fds which result from opening the special file
won't correspond to host fds, so to ensure that we don't end up
with duplicate fds we need to have QEMU code control the allocation
of the fd values we give the guest.
Add in an abstraction layer which lets us allocate new guest FD
values, and translate from a guest FD value back to the host one.
This also fixes an odd hole where a semihosting guest could
use the semihosting API to read, write or close file descriptors
that it had never allocated but which were being used by QEMU itself.
(This isn't a security hole, because enabling semihosting permits
the guest to do arbitrary file access to the whole host filesystem,
and so should only be done if the guest is completely trusted.)
Currently the only kind of guest fd is one which maps to a
host fd, but in a following commit we will add one which maps
to the :semihosting-features magic data.
If the guest is migrated with an open semihosting file descriptor
then subsequent attempts to use the fd will all fail; this is
not a change from the previous situation (where the host fd
being used on the source end would not be re-opened on the
destination end).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190916141544.17540-5-peter.maydell@linaro.org
In arm_gdb_syscall() we have a comment suggesting a race
because the syscall completion callback might not happen
before the gdb_do_syscallv() call returns. The comment is
correct that the callback may not happen but incorrect about
the effects. Correct it and note the important caveat that
callers must never do any work of any kind after return from
arm_gdb_syscall() that depends on its return value.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190916141544.17540-4-peter.maydell@linaro.org
If we fail a semihosting call we should always set the
semihosting errno to something; we were failing to do
this for some of the "check inputs for sanity" cases.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190916141544.17540-3-peter.maydell@linaro.org
The set_swi_errno() function is called to capture the errno
from a host system call, so that we can return -1 from the
semihosting function and later allow the guest to get a more
specific error code with the SYS_ERRNO function. It comes in
two versions, one for user-only and one for softmmu. We forgot
to capture the errno in the softmmu version; fix the error.
(Semihosting calls directed to gdb are unaffected because
they go through a different code path that captures the
error return from the gdbstub call in arm_semi_cb() or
arm_semi_flen_cb().)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190916141544.17540-2-peter.maydell@linaro.org
Host kernel within [4.18, 5.3] report an erroneous KVM_MAX_VCPUS=512
for ARM. The actual capability to instantiate more than 256 vcpus
was fixed in 5.4 with the upgrade of the KVM_IRQ_LINE ABI to support
vcpu id encoded on 12 bits instead of 8 and a redistributor consuming
a single KVM IO device instead of 2.
So let's check this capability when attempting to use more than 256
vcpus within any ARM kvm accelerated machine.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Message-id: 20191003154640.22451-4-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Host kernels that expose the KVM_CAP_ARM_IRQ_LINE_LAYOUT_2 capability
allow injection of interrupts along with vcpu ids larger than 255.
Let's encode the vpcu id on 12 bits according to the upgraded KVM_IRQ_LINE
ABI when needed.
Given that we have two callsites that need to assemble
the value for kvm_set_irq(), a new helper routine, kvm_arm_set_irq
is introduced.
Without that patch qemu exits with "kvm_set_irq: Invalid argument"
message.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Message-id: 20191003154640.22451-3-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
MVCL is interruptible and we should check for interrupts and process
them after writing back the variables to the registers. Let's check
for any exit requests and exit to the main loop. Introduce a new helper
function for that: cpu_loop_exit_requested().
When booting Fedora 30, I can see a handful of these exits and it seems
to work reliable. Also, Richard explained why this works correctly even
when MVCL is called via EXECUTE:
(1) TB with EXECUTE runs, at address Ae
- env->psw_addr stored with Ae.
- helper_ex() runs, memory address Am computed
from D2a(X2a,B2a) or from psw.addr+RI2.
- env->ex_value stored with memory value modified by R1a
(2) TB of executee runs,
- env->ex_value stored with 0.
- helper_mvcl() runs, using and updating R1b, R1b+1, R2b, R2b+1.
(3a) helper_mvcl() completes,
- TB of executee continues, psw.addr += ilen.
- Next instruction is the one following EXECUTE.
(3b) helper_mvcl() exits to main loop,
- cpu_loop_exit_restore() unwinds psw.addr = Ae.
- Next instruction is the EXECUTE itself...
- goto 1.
As the PoP mentiones that an interruptible instruction called via EXECUTE
should avoid modifying storage/registers that are used by EXECUTE itself,
it is fine to retrigger EXECUTE.
Cc: Alex Bennée <alex.bennee@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
This setting is no longer used.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191001171614.8405-19-richard.henderson@linaro.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
All but one caller passes ILEN_UNWIND, which is not stored.
For the one use case in s390_cpu_tlb_fill, set int_pgm_ilen
directly, simply to avoid the assert within do_program_interrupt.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191001171614.8405-18-richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
The single caller passes ILEN_UNWIND; pass that along to
trigger_pgm_exception directly.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191001171614.8405-17-richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
This setting is no longer used.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191001171614.8405-16-richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
For TCG, we will always call s390_cpu_virt_mem_handle_exc,
which will go through the unwinder to set ILEN. For KVM,
we do not go through do_program_interrupt, so this argument
is unused.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191001171614.8405-15-richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
We currently set ilen to AUTO, then overwrite that during
unwinding, then overwrite that for the code access case.
This can be simplified to setting ilen to our arbitrary
value for the (undefined) code access case, then rely on
unwinding to overwrite that with the correct value for
the data access case.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191001171614.8405-14-richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
We currently call trigger_pgm_exception to set cs->exception_index
and env->int_pgm_code and then read the values back and then
reset cs->exception_index so that the exception is not delivered.
Instead, use the exception type that we already have directly
without ever triggering an exception that must be suppressed.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191001171614.8405-13-richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Now that excp always contains a real exception number, we can
use that instead of a separate fail variable. This allows a
redundant test to be removed.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191001171614.8405-12-richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Do not raise the exception directly within translate_pages,
but pass it back so that caller may do so.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191001171614.8405-11-richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Do not raise the exception directly within mmu_translate,
but pass it back so that caller may do so.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191001171614.8405-10-richard.henderson@linaro.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Now that mmu_translate_asce returns the exception instead of
raising it, the argument is unused.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191001171614.8405-9-richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Do not raise the exception directly within mmu_translate_real,
but pass it back so that caller may do so.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191001171614.8405-8-richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
As a step toward moving all excption handling out of mmu_translate,
copy handling of the LowCore tec value from trigger_access_exception
into s390_cpu_tlb_fill. So far this new plumbing isn't used.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191001171614.8405-7-richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Delay triggering an exception until the end, after we have
determined ultimate success or failure, and also taken into
account whether this is a non-faulting probe.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191001171614.8405-6-richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Replace all uses of s390_program_interrupt within files
that are marked CONFIG_TCG. These are necessarily tcg-only.
This lets each of these users benefit from the QEMU_NORETURN
attribute on tcg_s390_program_interrupt.
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191001171614.8405-5-richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
This is no longer used, and many of the existing uses -- particularly
within hw/s390x -- seem questionable.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191001171614.8405-4-richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Since we begin the operation with an unwind, we have the proper
value of ilen immediately available.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191001171614.8405-3-richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Use ILEN_UNWIND to signal that we have in fact that cpu_restore_state
will have been called by the time we arrive in do_program_interrupt.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-Id: <20191001171614.8405-2-richard.henderson@linaro.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
We now implement a bunch of new facilities we can properly indicate.
ESOP-1/ESOP-2 handling is discussed in the PoP Chafter 3-15
("Suppression on Protection"). The "Basic suppression-on-protection (SOP)
facility" is a core part of z/Architecture without a facility
indication. ESOP-2 is indicated by ESOP-1 + Side-effect facility
("ESOP-2"). Besides ESOP-2, the side-effect facility is only relevant for
the guarded-storage facility (we don't implement).
S390_ESOP:
- We indicate DAT exeptions by setting bit 61 of the TEID (TEC) to 1 and
bit 60 to zero. We don't trigger ALCP exceptions yet. Also, we set
bit 0-51 and bit 62/63 to the right values.
S390_ACCESS_EXCEPTION_FS_INDICATION:
- The TEID (TEC) properly indicates in bit 52/53 on any access if it was
a fetch or a store
S390_SIDE_EFFECT_ACCESS_ESOP2:
- We have no side-effect accesses (esp., we don't implement the
guarded-storage faciliy), we correctly set bit 64 of the TEID (TEC) to
0 (no side-effect).
- ESOP2: We properly set bit 56, 60, 61 in the TEID (TEC) to indicate the
type of protection. We don't trigger KCP/ALCP exceptions yet.
S390_INSTRUCTION_EXEC_PROT:
- The MMU properly detects and indicates the exception on instruction fetches
- Protected TLB entries will never get PAGE_EXEC set.
There is no need to fake the abscence of any of the facilities - without
the facilities, some bits of the TEID (TEC) are simply unpredictable.
As IEP was added with z14 and we currently implement a z13, add it to
the MAX model instead.
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Setup the 4.1 compatibility model so we can add new features to the
LATEST model.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
IEP support in the mmu is fairly easy. Set the right permissions for TLB
entries and properly report an exception.
Make sure to handle EDAT-2 by setting bit 56/60/61 of the TEID (TEC) to
the right values.
Let's keep s390_cpu_get_phys_page_debug() working even if IEP is
active. Switch MMU_DATA_LOAD - this has no other effects any more as the
ASC to be used is now fully selected outside of mmu_translate().
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
We already implement ESOP-1. For ESOP-2, we only have to indicate all
protection exceptions properly. Due to EDAT-1, we already indicate DAT
exceptions properly. We don't trigger KCP/ALCP/IEP exceptions yet.
So all we have to do is set the TEID (TEC) to the right values
(bit 56, 60, 61) in case of LAP.
We don't have any side-effects (e.g., no guarded-storage facility),
therefore, bit 64 of the TEID (TEC) is always 0.
We always have to indicate whether it is a fetch or a store for all access
exceptions. This is only missing for LAP exceptions.
Acked-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
This only adds basic support to the DAT translation, but no EDAT2 support
for TCG. E.g., the gdbstub under kvm uses this function, too, to
translate virtual addresses.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
A non-recursive implementation allows to make better use of the
branch predictor, avoids function calls, and makes the implementation of
new features only for a subset of region table levels easier.
We can now directly compare our implementation to the KVM gaccess
implementation in arch/s390/kvm/gaccess.c:guest_translate().
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's use consistent names for the region/section/page table entries and
for the macros to extract relevant parts from virtual address. Make them
match the definitions in the PoP - e.g., how the relevant bits are actually
called.
Introduce defines for all bits declared in the PoP. This will come in
handy in follow-up patches.
Add a note where additional information about s390x and the used
definitions can be found.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
While ASCE_ORIGIN is not wrong, it is certainly confusing. We want a
page frame address.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's document how it works and inject PGM_ADDRESSING if reading of
table entries fails.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's return the PGM from the translation functions on error and inject
based on that.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
We'll reuse the ilen and tec definitions in mmu_translate
soon also for all other DAT exceptions we inject. Move it to the caller,
where we can later pair it up with other protection checks, like IEP.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's get it out of the way to make some further refactorings easier.
Personally, I've never used these debug statements at all. And if I had
to debug issues, I used plain GDB instead (debug prints are just way too
much noise in the MMU). We might want to introduce tracing at some point
instead, so we can able selected events on demand.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Here's the next batch of ppc and spapr patches. Includes:
* Fist part of a large cleanup to irq infrastructure
* Recreate the full FDT at CAS time, instead of making a difficult
to follow set of updates. This will help us move towards
eliminating CAS reboots altogether
* No longer provide RTAS blob to SLOF - SLOF can include it just as
well itself, since guests will generally need to relocate it with
a call to instantiate-rtas
* A number of DFP fixes and cleanups from Mark Cave-Ayland
* Assorted bugfixes
* Several new small devices for powernv
-----BEGIN PGP SIGNATURE-----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=PXXe
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.2-20191004' into staging
ppc patch queue 2019-10-04
Here's the next batch of ppc and spapr patches. Includes:
* Fist part of a large cleanup to irq infrastructure
* Recreate the full FDT at CAS time, instead of making a difficult
to follow set of updates. This will help us move towards
eliminating CAS reboots altogether
* No longer provide RTAS blob to SLOF - SLOF can include it just as
well itself, since guests will generally need to relocate it with
a call to instantiate-rtas
* A number of DFP fixes and cleanups from Mark Cave-Ayland
* Assorted bugfixes
* Several new small devices for powernv
# gpg: Signature made Fri 04 Oct 2019 10:35:57 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.2-20191004: (53 commits)
ppc/pnv: Remove the XICSFabric Interface from the POWER9 machine
spapr: Eliminate SpaprIrq::init hook
spapr: Add return value to spapr_irq_check()
spapr: Use less cryptic representation of which irq backends are supported
xive: Improve irq claim/free path
spapr, xics, xive: Better use of assert()s on irq claim/free paths
spapr: Handle freeing of multiple irqs in frontend only
spapr: Remove unhelpful tracepoints from spapr_irq_free_xics()
spapr: Eliminate SpaprIrq:get_nodename method
spapr: Simplify spapr_qirq() handling
spapr: Fix indexing of XICS irqs
spapr: Eliminate nr_irqs parameter to SpaprIrq::init
spapr: Clarify and fix handling of nr_irqs
spapr: Replace spapr_vio_qirq() helper with spapr_vio_irq_pulse() helper
spapr: Fold spapr_phb_lsi_qirq() into its single caller
xics: Create sPAPR specific ICS subtype
xics: Merge TYPE_ICS_BASE and TYPE_ICS_SIMPLE classes
xics: Eliminate reset hook
xics: Rename misleading ics_simple_*() functions
xics: Eliminate 'reject', 'resend' and 'eoi' class hooks
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When I run QEMU with KVM under Valgrind, I currently get this warning:
Syscall param ioctl(generic) points to uninitialised byte(s)
at 0x95BA45B: ioctl (in /usr/lib64/libc-2.28.so)
by 0x429DC3: kvm_ioctl (kvm-all.c:2365)
by 0x51B249: kvm_arch_get_supported_msr_feature (kvm.c:469)
by 0x4C2A49: x86_cpu_get_supported_feature_word (cpu.c:3765)
by 0x4C4116: x86_cpu_expand_features (cpu.c:5065)
by 0x4C7F8D: x86_cpu_realizefn (cpu.c:5242)
by 0x5961F3: device_set_realized (qdev.c:835)
by 0x7038F6: property_set_bool (object.c:2080)
by 0x707EFE: object_property_set_qobject (qom-qobject.c:26)
by 0x705814: object_property_set_bool (object.c:1338)
by 0x498435: pc_new_cpu (pc.c:1549)
by 0x49C67D: pc_cpus_init (pc.c:1681)
Address 0x1ffeffee74 is on thread 1's stack
in frame #2, created by kvm_arch_get_supported_msr_feature (kvm.c:445)
It's harmless, but a little bit annoying, so silence it by properly
initializing the whole structure with zeroes.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some secondary controls are automatically enabled/disabled based on the CPUID
values that are set for the guest. However, they are still available at a
global level and therefore should be present when KVM_GET_MSRS is sent to
/dev/kvm.
Unfortunately KVM forgot to include those, so fix that.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add code to convert the VMX feature words back into MSR values,
allowing the user to enable/disable VMX features as they wish. The same
infrastructure enables support for limiting VMX features in named
CPU models.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These will be used to compile the list of VMX features for named
CPU models, and/or by the code that sets up the VMX MSRs.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMX requires 64-bit feature words for the IA32_VMX_EPT_VPID_CAP
and IA32_VMX_BASIC MSRs. (The VMX control MSRs are 64-bit wide but
actually have only 32 bits of information).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Sometimes a CPU feature does not make sense unless another is
present. In the case of VMX features, KVM does not even allow
setting the VMX controls to some invalid combinations.
Therefore, this patch adds a generic mechanism that looks for bits
that the user explicitly cleared, and uses them to remove other bits
from the expanded CPU definition. If these dependent bits were also
explicitly *set* by the user, this will be a warning for "-cpu check"
and an error for "-cpu enforce". If not, then the dependent bits are
cleared silently, for convenience.
With VMX features, this will be used so that for example
"-cpu host,-rdrand" will also hide support for RDRAND exiting.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The next patch will add a different reason for filtering features, unrelated
to host feature support. Extract a new function that takes care of disabling
the features and optionally reporting them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is a problem, that you don't have access to the data using cpu_memory_rw_debug() function when in SMM. You can't remotely debug SMM mode program because of that for example.
Likely attrs version of get_phys_page_debug should be used to get correct asidx at the end to handle access properly.
Here the patch to fix it.
Signed-off-by: Dmitry Poletaev <poletaev@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The CPUID bits CLZERO and XSAVEERPTR are availble on AMD's ZEN platform
and could be passed to the guest.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows us to remove more endian-specific defines from int_helper.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20190926204453.31837-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Now that the parameters to both set_dfp64() and set_dfp128() are exactly the
same, there is no need for an explicit if() statement to determine which
function should be called based upon size. Instead we can simply use the
preprocessor to generate the call to set_dfp##size() directly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20190926185801.11176-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Switch over all accesses to the decimal numbers held in struct PPC_DFP from
using HI_IDX and LO_IDX to using the VsrD() macro instead. Not only does this
allow the compiler to ensure that the various dfp_* functions are being passed
a ppc_vsr_t rather than an arbitrary uint64_t pointer, but also allows the
host endian-specific HI_IDX and LO_IDX to be completely removed from
dfp_helper.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20190926185801.11176-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There are several places in dfp_helper.c that access the decimal number
representations in struct PPC_DFP via HI_IDX and LO_IDX defines which are set
at the top of dfp_helper.c according to the host endian.
However we can instead switch to using ppc_vsr_t for decimal numbers and then
make subsequent use of the existing VsrD() macros to access the correct
element regardless of host endian. Note that 64-bit decimals are stored in the
LSB of ppc_vsr_t (equivalent to VsrD(1)).
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20190926185801.11176-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Most of the DFP helper functions call decimal{64,128}FromNumber() just before
returning in order to convert the decNumber stored in dfp.t64 back to a
Decimal{64,128} to write back to the FP registers.
Introduce new dfp_finalize_decimal{64,128}() helper functions which both enable
the parameter list to be reduced considerably, and also help minimise the
changes required in the next patch.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20190926185801.11176-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since commit ef96e3ae96 "target/ppc: move FP and VMX registers into aligned vsr
register array" FP registers are no longer stored consecutively in memory and so
the current method of combining FP register pairs into DFP numbers is incorrect.
Firstly update the definition of the dh_*_fprp defines in helper.h to reflect
that FP registers are now stored as part of an array of ppc_vsr_t elements
rather than plain uint64_t elements, and then introduce a new ppc_fprp_t type
which conceptually represents a DFP even-odd register pair to be consumed by the
DFP helper functions.
Finally update the new DFP {get,set}_dfp{64,128}() helper functions to convert
between DFP numbers and DFP even-odd register pairs correctly, making use of the
existing VsrD() macro to access the correct elements regardless of host endian.
Fixes: ef96e3ae96 "target/ppc: move FP and VMX registers into aligned vsr register array"
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20190926185801.11176-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The existing functions (now incorrectly) assume that the MSB and LSB of DFP
numbers are stored as consecutive 64-bit words in memory. Instead of accessing
the DFP numbers directly, introduce set_dfp{64,128}() helper functions to ease
the switch to the correct representation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20190926185801.11176-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The existing functions (now incorrectly) assume that the MSB and LSB of DFP
numbers are stored as consecutive 64-bit words in memory. Instead of accessing
the DFP numbers directly, introduce get_dfp{64,128}() helper functions to ease
the switch to the correct representation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20190926185801.11176-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On POWER8 systems the Directed Privileged Door-bell Exception State
register (DPDES) stores doorbell pending status, one bit per a thread
of a core, set by "msgsndp" instruction. The register is shared among
threads of the same core and KVM on POWER9 emulates it in a similar way
(POWER9 does not have DPDES).
DPDES is shared but QEMU assumes all SPRs are per thread so the only safe
way to write DPDES back to VCPU before running a guest is doing so
while all threads are pulled out of the guest so DPDES cannot change.
There is only one situation when this condition is met: incoming migration
when all threads are stopped. Otherwise any QEMU HMP/QMP command causing
kvm_arch_put_registers() (for example printing registers or dumping memory)
can clobber DPDES in a race with other vcpu threads.
This changes DPDES handling so it is not written to KVM at runtime.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20190923084110.34643-1-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There are FPSCR-related defines in target/ppc/cpu.h which can be used in
place of constants and explicit shifts which arguably improve the code a
bit in places.
Signed-off-by: Paul A. Clarke <pc@us.ibm.com>
Message-Id: <1568817169-1721-1-git-send-email-pc@us.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
ISA 3.0B added a set of Floating-Point Status and Control Register (FPSCR)
instructions: mffsce, mffscdrn, mffscdrni, mffscrn, mffscrni, mffsl.
This patch adds support for 'mffsce' instruction.
'mffsce' is identical to 'mffs', except that it also clears the exception
enable bits in the FPSCR.
On CPUs without support for 'mffsce' (below ISA 3.0), the
instruction will execute identically to 'mffs'.
Signed-off-by: Paul A. Clarke <pc@us.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <1568817082-1384-1-git-send-email-pc@us.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
ISA 3.0B added a set of Floating-Point Status and Control Register (FPSCR)
instructions: mffsce, mffscdrn, mffscdrni, mffscrn, mffscrni, mffsl.
This patch adds support for 'mffscrn' and 'mffscrni' instructions.
'mffscrn' and 'mffscrni' are similar to 'mffsl', except they do not return
the status bits (FI, FR, FPRF) and they also set the rounding mode in the
FPSCR.
On CPUs without support for 'mffscrn'/'mffscrni' (below ISA 3.0), the
instructions will execute identically to 'mffs'.
Signed-off-by: Paul A. Clarke <pc@us.ibm.com>
Message-Id: <1568817081-1345-1-git-send-email-pc@us.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Mostly fix errors and warnings reported by 'checkpatch.pl -f'.
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Rikalo <arikalo@wavecomp.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1569331602-2586-7-git-send-email-aleksandar.markovic@rt-rk.com>
Mostly fix errors and warnings reported by 'checkpatch.pl -f'.
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Rikalo <arikalo@wavecomp.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1569331602-2586-5-git-send-email-aleksandar.markovic@rt-rk.com>
Mostly fix errors and warnings reported by 'checkpatch.pl -f'.
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Rikalo <arikalo@wavecomp.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1569331602-2586-4-git-send-email-aleksandar.markovic@rt-rk.com>
Mostly fix errors and warnings reported by 'checkpatch.pl -f'.
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Rikalo <arikalo@wavecomp.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1569331602-2586-3-git-send-email-aleksandar.markovic@rt-rk.com>
Instead of splitting at an unaligned address, we can simply split at
4TB.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
s390 was trying to solve limited KVM memslot size issue by abusing
memory_region_allocate_system_memory(), which breaks API contract
where the function might be called only once.
Beside an invalid use of API, the approach also introduced migration
issue, since RAM chunks for each KVM_SLOT_MAX_BYTES are transferred in
migration stream as separate RAMBlocks.
After discussion [1], it was agreed to break migration from older
QEMU for guest with RAM >8Tb (as it was relatively new (since 2.12)
and considered to be not actually used downstream).
Migration should keep working for guests with less than 8TB and for
more than 8TB with QEMU 4.2 and newer binary.
In case user tries to migrate more than 8TB guest, between incompatible
QEMU versions, migration should fail gracefully due to non-exiting
RAMBlock ID or RAMBlock size mismatch.
Taking in account above and that now KVM code is able to split too
big MemorySection into several memslots, partially revert commit
(bb223055b s390-ccw-virtio: allow for systems larger that 7.999TB)
and use kvm_set_max_memslot_size() to set KVMSlot size to
KVM_SLOT_MAX_BYTES.
1) [PATCH RFC v2 4/4] s390: do not call memory_region_allocate_system_memory() multiple times
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190924144751.24149-5-imammedo@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
* Fix the CBAR register implementation for Cortex-A53,
Cortex-A57, Cortex-A72
* Fix direct booting of Linux kernels on emulated CPUs
which have an AArch32 EL3 (incorrect NSACR settings
meant they could not access the FPU)
* semihosting cleanup: do more work at translate time
and less work at runtime
-----BEGIN PGP SIGNATURE-----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=/0m2
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20190927' into staging
target-arm queue:
* Fix the CBAR register implementation for Cortex-A53,
Cortex-A57, Cortex-A72
* Fix direct booting of Linux kernels on emulated CPUs
which have an AArch32 EL3 (incorrect NSACR settings
meant they could not access the FPU)
* semihosting cleanup: do more work at translate time
and less work at runtime
# gpg: Signature made Fri 27 Sep 2019 15:32:43 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20190927:
hw/arm/boot: Use the IEC binary prefix definitions
hw/arm/boot.c: Set NSACR.{CP11,CP10} for NS kernel boots
tests/tcg: add linux-user semihosting smoke test for ARM
target/arm: remove run-time semihosting checks for linux-user
target/arm: remove run time semihosting checks
target/arm: handle A-profile semihosting at translate time
target/arm: handle M-profile semihosting at translate time
tests/tcg: clean-up some comments after the de-tangling
target/arm: fix CBAR register for AArch64 CPUs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# tests/tcg/arm/Makefile.target
Now we do all our checking and use a common EXCP_SEMIHOST for
semihosting operations we can make helper code a lot simpler.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190913151845.12582-5-alex.bennee@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As for the other semihosting calls we can resolve this at translate
time.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190913151845.12582-4-alex.bennee@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We do this for other semihosting calls so we might as well do it for
M-profile as well.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190913151845.12582-3-alex.bennee@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For AArch64 CPUs with a CBAR register, we have two views for it:
- in AArch64 state, the CBAR_EL1 register (S3_1_C15_C3_0), returns the
full 64 bits CBAR value
- in AArch32 state, the CBAR register (cp15, opc1=1, CRn=15, CRm=3, opc2=0)
returns a 32 bits view such that:
CBAR = CBAR_EL1[31:18] 0..0 CBAR_EL1[43:32]
This commit fixes the current implementation where:
- CBAR_EL1 was returning the 32 bits view instead of the full 64 bits
value,
- CBAR was returning a truncated 32 bits version of the full 64 bits
one, instead of the 32 bits view
- CBAR was declared as cp15, opc1=4, CRn=15, CRm=0, opc2=0, which is
the CBAR register found in the ARMv7 Cortex-Ax CPUs, but not in
ARMv8 CPUs.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20190912110103.1417887-1-luc.michel@greensocs.com
[PMM: Added a comment about the two different kinds of CBAR]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The WHPX build is broken since commit 12e9493df9 which removed the
"hw/boards.h" where MachineState is declared:
$ ./configure \
--enable-hax --enable-whpx
$ make x86_64-softmmu/all
[...]
CC x86_64-softmmu/target/i386/whpx-all.o
target/i386/whpx-all.c: In function 'whpx_accel_init':
target/i386/whpx-all.c:1378:25: error: dereferencing pointer to
incomplete type 'MachineState' {aka 'struct MachineState'}
whpx->mem_quota = ms->ram_size;
^~
make[1]: *** [rules.mak:69: target/i386/whpx-all.o] Error 1
CC x86_64-softmmu/trace/generated-helpers.o
make[1]: Target 'all' not remade because of errors.
make: *** [Makefile:471: x86_64-softmmu/all] Error 2
Restore this header, partially reverting commit 12e9493df9.
Fixes: 12e9493df9
Reported-by: Ilias Maratos <i.maratos@gmail.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190920113329.16787-2-philmd@redhat.com>
Remove a redundant masking of ignore. Once that's gone it is
obvious that the system-mode inner test is redundant with the
outer test. Move the fpcr_exc_enable masking up and tidy.
No functional change.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190921043256.4575-8-richard.henderson@linaro.org>
The kernel masks the integer overflow exception with the
software invalid exception mask. Include IOV in the set
of exception bits masked by fpcr_exc_enable.
Fixes the new float_convs test.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190921043256.4575-7-richard.henderson@linaro.org>
Tidy the computation of the value; no functional change.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190921043256.4575-6-richard.henderson@linaro.org>
Since we're converting the swcr to fpcr format for exceptions,
it's trivial to add FPCR_DNZ to the set of fpcr bits overriden.
No functional change.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190921043256.4575-5-richard.henderson@linaro.org>
The CONFIG_USER_ONLY adjustment blindly mashed the swcr
exception enable bits into the fpcr exception disable bits.
However, fpcr_exc_enable has already converted the exception
disable bits into the exception status bits in order to make
it easier to mask status bits at runtime.
Instead, merge the swcr enable bits with the fpcr before we
convert to status bits.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190921043256.4575-4-richard.henderson@linaro.org>
We were setting the wrong bit. The fp_status.flush_to_zero
setting is overwritten by either the constant 1 or the value
of fpcr_flush_to_zero depending on bits within an fp insn.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190921043256.4575-3-richard.henderson@linaro.org>
This is a bit more straight-forward than using a switch statement.
No functional change.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190921043256.4575-2-richard.henderson@linaro.org>
Each operand can have a maximum length of 16. Make sure to prepare all
reads/writes before writing.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Access at most single pages and document why. Using the access helpers
might over-indicate watchpoints within the same page, I guess we can
live with that.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
We can process a maximum of 256 bytes, crossing two pages.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
We can process a maximum of 256 bytes, crossing two pages.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
We can process a maximum of 256 bytes, crossing two pages. Calculate the
accessed range upfront - src is accessed right-to-left.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
We can process a maximum of 256 bytes, crossing two pages.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
We can process a maximum of 256 bytes, crossing two pages. While at it,
increment the length once.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
We can process a maximum of 256 bytes, crossing two pages.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
The last remaining bit is padding with two bytes.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
The last remaining bit for MVC is handling destructive overlaps in a
fault-safe way.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
As we are moving between address spaces, we can use access_memmove()
without checking for destructive overlaps (especially of real storage
locations):
"Each storage operand is processed left to right. The
storage-operand-consistency rules are the same as
for MOVE (MVC), except that when the operands
overlap in real storage, the use of the common real-
storage locations is not necessarily recognized."
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Replace fast_memmove() variants by access_memmove() variants, that
first try to probe access to all affected pages (maximum is two pages).
Introduce access_get_byte()/access_set_byte(). We might be able to speed
up memmove in special cases even further (do single-byte access, use
memmove() for remaining bytes in page), however, we'll skip that for now.
In MVCOS, simply always call access_memmove_as() and drop the TODO
about LAP. LAP is already handled in the MMU.
Get rid of adj_len_to_page(), which is now unused.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Replace fast_memset() by access_memset(), that first tries to probe
access to all affected pages (maximum is two). We'll use the same
mechanism for other types of accesses soon.
Only in very rare cases (especially TLB_NOTDIRTY), we'll have to
fallback to ld/st helpers. Try to speed up that case as suggested by
Richard.
We'll rework most involved handlers soon to do all accesses via new
fault-safe helpers, especially MVC.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Although we basically ignore the index all the time for CONFIG_USER_ONLY,
let's simply skip all the checks and always return MMU_USER_IDX in
cpu_mmu_index() and get_mem_index().
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
24 and 31-bit address space handling is wrong when it comes to storing
back the addresses to the register.
While at it, read gprs 0 implicitly.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Bit position 32-55 of general register 0 must be zero.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
... and don't perform any move in case the length is zero.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Triggered by a review comment from Richard, also MVCOS has a 32-bit
length in 24/31-bit addressing mode. Add a new helper.
Rename wrap_length() to wrap_length31().
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's stay within single pages.
... and indicate cc=3 in case there is work remaining. Keep unicode
padding simple.
While reworking, properly wrap the addresses.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
We have to mask of any unused bits. While at it, document what exactly is
missing.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Perform the checks documented in the PoP.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's use the new helper, that also detects destructive overlaps when
wrapping.
We'll make the remaining code (e.g., fast_memmove()) aware of wrapping
later.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's increment the length once.
While at it, cleanup the comment. The memset() example is given as a
programming note in the PoP, so drop the description.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Process max 4k bytes at a time, writing back registers between the
accesses. The instruction is interruptible.
"For operands longer than 2K bytes, access exceptions are not
recognized for locations more than 2K bytes beyond the current location
being processed."
Note that on z/Architecture, 2k vs. 4k access cannot get differentiated as
long as pages are not crossed. This seems to be a leftover from ESA/390.
Simply stay within single pages.
MVCL handling is quite different than MVCLE/MVCLU handling, so split up
the handlers.
Defer interrupt handling, as that will require more thought, add a TODO
for that.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
We'll have to zero-out unused bit positions, so make sure to write the
addresses back.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
We have to zero out unused bits in 24 and 31-bit addressing mode.
Provide a new helper.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
We use the marker "-1" for "no exception". s390_cpu_do_interrupt() might
get confused by that.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Since QEMU v2.10, the KVM acceleration does not work on older kernels
anymore since the code accidentally requires the KVM_CAP_DEVICE_CTRL
capability now - it should have been optional instead.
Instead of fixing the bug, we asked in the ChangeLog of QEMU 2.11 - 3.0
that people should speak up if they still need support of QEMU running
with KVM on older kernels, but seems like nobody really complained.
Thus let's make this official now and turn it into a proper error
message, telling the users to use at least kernel 3.15 now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190913091443.27565-1-thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The "access" arguments clash with a macro under Windows with MinGW:
CC m68k-softmmu/target/m68k/fpu_helper.o
target/m68k/fpu_helper.c: In function 'fmovem_predec':
target/m68k/fpu_helper.c:405:56: error: macro "access" passed 4 arguments,
but takes just 2
size = access(env, addr, &env->fregs[i], ra);
So this renames them access_fn.
Tested with:
./configure --target-list=m68k-softmmu
make -j8
Signed-off-by: KONRAD Frederic <frederic.konrad@adacore.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <1568296920-29939-1-git-send-email-frederic.konrad@adacore.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
While debugging an application with GDB the following might happen:
(gdb) return
Make xxx return now? (y or n) y
Could not fetch register "fflags"; remote failure reply 'E14'
This is because riscv_gdb_get_fpu calls riscv_csrrw_debug with a wrong csr
number (8). It should use the csr_register_map in order to reach the
riscv_cpu_get_fflags callback.
Signed-off-by: KONRAD Frederic <frederic.konrad@adacore.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Use the TB_FLAGS_MSTATUS_FS macro when enabling floating point in the tb
flags.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This is meant to mask off the hypervisor bits, but a typo caused it to
mask MPP instead.
Fixes: 1f0419cb04 ("target/riscv: Allow setting mstatus virtulisation bits")
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Use both the generic register name and ABI name for the general purpose
registers and floating point registers.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This adds 'info mem' command for RISC-V, to show virtual memory
mappings that aids debugging.
Rather than showing every valid PTE, the command compacts the
output by merging all contiguous physical address mappings into
one block and only shows the merged block mapping details.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
For RV32, the root page table's PPN has 22 bits hence its address
bits could be larger than the maximum bits that target_ulong is
able to represent. Use hwaddr instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Update the Hypervisor CSR addresses to match the v0.4 spec.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Let's create a function that tests if floating point support is
enabled. We can then protect all floating point operations based on if
they are enabled.
This patch so far doesn't change anything, it's just preparing for the
Hypervisor support for floating point operations.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Christophe de Dinechin <dinechin@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Use the always-compiled trace events, remove the now unused
RISCV_DEBUG_PMP definition.
Note pmpaddr_csr_read() could previously do out-of-bound accesses
passing addr_index >= MAX_RISCV_PMPS.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The RISC-V Physical Memory Protection is restricted to privileged
modes. Restrict its compilation to QEMU system builds.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Switch the SPARC target from the old unassigned_access hook to the
new do_transaction_failed hook.
This will cause the "if transaction failed" code paths added in
the previous commits to become active if the access is to an
unassigned address. In particular we'll now handle bus errors
during page table walks correctly (generating a translation
error with the right kind of fault status).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20190801183012.17564-8-peter.maydell@linaro.org
The dump_mmu() function does a ldl_phys() at the start, but
then never uses the value it loads at all. Remove the
unused code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20190801183012.17564-7-peter.maydell@linaro.org
Convert the mmu_probe() function to using address_space_ldl()
rather than ldl_phys(), so we can explicitly detect memory
transaction failures.
This makes no practical difference at the moment, because
ldl_phys() will return 0 on a transaction failure, and we
treat transaction failures and 0 PDEs identically. However
the spec says that MMU probe operations are supposed to
update the fault status registers, and if we ever implement
that we'll want to distinguish the difference. For the
moment, just add a TODO comment about the bug.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20190801183012.17564-6-peter.maydell@linaro.org
Currently we use the ldl_phys() function to read page table entries.
With the unassigned_access hook in place, if these hit an unassigned
area of memory then the hook will cause us to wrongly generate
an exception with a fault address matching the address of the
page table entry.
Change to using address_space_ldl() so we can detect and correctly
handle bus errors and give them their correct behaviour of
causing a translation error with a suitable fault status register.
Note that this won't actually take effect until we switch the
over to using the do_translation_failed hook.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20190801183012.17564-5-peter.maydell@linaro.org
Currently the ld/st_asi helper functions make calls to the
ld*_phys() and st*_phys() functions for those ASIs which
imply direct accesses to physical addresses. These implicitly
rely on the unassigned_access hook to cause them to generate
an MMU fault if the access fails.
Switch to using the address_space_* functions instead, which
return a MemTxResult that we can check. This means that when
we switch SPARC over to using the do_transaction_failed hook
we'll still get the same MMU faults we did before.
This commit converts the ASIs which do MXCC stream source
and destination accesses.
It's not clear to me whether raising an MMU fault like this
is the correct behaviour if we encounter a bus error, but
we retain the same behaviour that the old unassigned_access
hook would implement.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20190801183012.17564-4-peter.maydell@linaro.org
Currently the ld/st_asi helper functions make calls to the
ld*_phys() and st*_phys() functions for those ASIs which
imply direct accesses to physical addresses. These implicitly
rely on the unassigned_access hook to cause them to generate
an MMU fault if the access fails.
Switch to using the address_space_* functions instead, which
return a MemTxResult that we can check. This means that when
we switch SPARC over to using the do_transaction_failed hook
we'll still get the same MMU faults we did before.
This commit converts the ASIs which do "MMU passthrough".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20190801183012.17564-3-peter.maydell@linaro.org
Currently the SPARC target uses the old-style do_unassigned_access
hook. We want to switch it over to do_transaction_failed, but to do
this we must first remove all the direct calls in ldst_helper.c to
cpu_unassigned_access(). Factor out the body of the hook function's
code into a new sparc_raise_mmu_fault() and call it from the hook and
from the various places that used to call cpu_unassigned_access().
In passing, this fixes a bug where the code that raised the
MMU exception was directly calling GETPC() from a function that
was several levels deep in the callstack from the original
helper function: the new sparc_raise_mmu_fault() instead takes
the return address as an argument.
Other than the use of retaddr rather than GETPC() and a comment
format fixup, the body of the new function has no changes from
that of the old hook function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20190801183012.17564-2-peter.maydell@linaro.org
Suggested-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190818225414.22590-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow guest reads CORE cstate when exposing host CPU power management capabilities
to the guest. PKG cstate is restricted to avoid a guest to get the whole package
information in multi-tenant scenario.
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1563154124-18579-1-git-send-email-wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
nullify_over() calls brcond which destroys all temporaries.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190913101714.29019-3-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
nullify_over() calls brcond which destroys all temporaries.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190913101714.29019-2-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Multiple reports from users were received regarding failures of
packet 'g' communication with gdb for some MIPS configurations.
It was found out (by bisecting) that the problematic commit is
8e0b373. Revert that commit until a better solution is developed.
Suggested-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Libo Zhou <zhlb29@foxmail.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1568207966-25202-1-git-send-email-aleksandar.markovic@rt-rk.com>
Switch the MIPS target from the old unassigned_access hook to the new
do_transaction_failed hook.
Unlike the old hook, do_transaction_failed is only ever called from
the TCG memory access paths, so there is no need for the "ignore this
if we're using KVM" hack that we were previously using to work around
the way unassigned_access was called for all kinds of memory accesses
to unassigned physical addresses.
The MIPS target does not ever do direct memory reads by physical
address (via either ldl_phys etc or address_space_ldl etc), so the
only memory accesses this affects are the 'normal' guest loads and
stores, which will be handled by the new hook; their behaviour is
unchanged.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20190802160458.25681-3-peter.maydell@linaro.org>
Xtensa binaries built for call0 ABI don't rotate register window on
function calls and returns. Invocation of signal handlers from the
kernel is therefore different in windowed and call0 ABIs.
There's currently no way to determine xtensa ELF binary ABI from the
binary itself. Add handler for the -xtensa-abi-call0 command line
parameter/QEMU_XTENSA_ABI_CALL0 envitonment variable to the qemu-user
and record ABI choice. Use it to initialize PS.WOE in xtensa_cpu_reset.
Check PS.WOE in setup_rt_frame to determine how a signal should be
delivered.
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20190906165713.5558-1-jcmvbkbc@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
There are only two remaining uses of gen_bx_im. In each case, we
know the destination mode -- not changing in the case of gen_jmp
or changing in the case of trans_BLX_i. Use this to simplify the
surrounding code.
For trans_BLX_i, use gen_jmp for the actual branch. For gen_jmp,
use gen_set_pc_im to set up the single-step.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-70-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that everything is converted, remove the rest of
the legacy decode.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-69-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-68-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-67-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-66-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-65-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-64-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-63-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-62-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that all callers pass a constant value, split the switch
statement into the individual trans_* functions.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190904193059.26202-61-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190904193059.26202-60-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-59-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a check for ARMv6 in trans_CPS. We had this correct in
the T16 path, but had previously forgotten the check on the
A32 and T32 paths.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-58-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-57-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-56-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-55-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-54-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-53-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-52-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-51-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-50-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-49-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-48-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-47-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-46-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fold away all of the cases that now just goto illegal_op,
because all of their internal bits are now in decodetree.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-45-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fold away all of the cases that now just goto illegal_op,
because all of their internal bits are now in decodetree.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-44-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-43-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-42-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-41-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-40-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-39-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-38-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-37-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-36-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-35-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-34-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-33-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We have been using store_reg and not store_reg_for_load when writing
back a loaded value into the base register. At first glance this is
incorrect when base == pc, however that case is UNPREDICTABLE.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-32-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This has been a TODO item for quite a while. The minimum bit
count for A32 and T16 is 1, and for T32 is 2.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-31-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Prior to v7, for the A32 encoding, this operation wrote an UNKNOWN
value back to the base register. Starting in v7 this is UNPREDICTABLE.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-30-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This includes a minor bug fix to LDM (user), which requires
bit 21 to be 0, which means no writeback.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-29-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-28-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-27-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-26-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-25-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In op_bfx, note that tcg_gen_{,s}extract_i32 already checks
for width == 32, so we don't need to special case that here.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-24-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-23-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-22-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-21-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-20-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-19-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Pass the T5 encoding of SUBS PC, LR, #IMM through the normal SUBS path
to make it clear exactly what's happening -- we hit ALUExceptionReturn
along that path.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-18-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Document our choice about the T32 CONSTRAINED UNPREDICTABLE behaviour.
This matches the undocumented choice made by the legacy decoder.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-17-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-16-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-15-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The m-profile and a-profile decodings overlap. Only return false
for the case of wrong profile; handle UNDEFINED for permission failure
directly. This ensures that we don't accidentally pass an insn that
applies to the wrong profile.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-14-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-13-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
By shifting the 16-bit input left by 16, we can align the desired
portion of the 48-bit product and use tcg_gen_muls2_i32.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-12-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since all of the inputs and outputs are i32, dispense with
the intermediate promotion to i64 and use tcg_gen_add2_i32.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-11-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-10-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-9-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since all of the inputs and outputs are i32, dispense with
the intermediate promotion to i64 and use tcg_gen_mulu2_i32
and tcg_gen_add2_i32.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-8-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-7-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert the modified immediate form of the data processing insns.
For A32, we can finally remove any code that was intertwined with
the register and register-shifted-register forms.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-6-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert the register shifted by register form of the data
processing insns. For A32, we cannot yet remove any code
because the legacy decoder intertwines the immediate form.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-5-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert the register shifted by immediate form of the data
processing insns. For A32, we cannot yet remove any code
because the legacy decoder intertwines the reg-shifted-reg
and immediate forms.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the infrastructure that will become the new decoder.
No instructions adjusted so far.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This function already includes the test for an interworking write
to PC from a load. Change the T32 LDM implementation to match the
A32 LDM implementation.
For LDM, the reordering of the tests does not change valid
behaviour because the only case that differs is has rn == 15,
which is UNPREDICTABLE.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190904193059.26202-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that the two updates from v1.3 are implemented,
update the "any" cpu to enable it.
Reviewed-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
These were added to the 1.3 spec. For OF32S, validate AVR.
But OF64A32 is itself new to 1.3 so no extra check needed.
Reviewed-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This is hardware support for double-precision floating-point using
pairs of 32-bit registers. Fix latent bugs in the heretofore unused
helper_itofd and helper_ftoid. Include the bit for cpu "any".
Change the default cpu for linux-user to "any".
Reviewed-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Richard Henderson